No power to level 2 switch

[007wall]

thread1329-1424937
Did anyone solve this problem, I have a similar problem, no power to switch.
Error comes up MIPS not up resetting level 2

 

[kwbMitel]

Is the licensing on the system?

**********************************************
What's most important is that you realise ... There is no spoon.

 

[sarond]

Did this happen after an upgrade?

 

[wireman50]

have you given the switch an IP address?

 

[007wall]

no upgrade.
The ip is correct.
Ive tried using another controller , swapping hard drives, and to see if the switch is broken, however it still doesnt have power, whereas the other drive works on both controllers??

 

[kwbMitel]

Licensing?

**********************************************
What's most important is that you realise ... There is no spoon.

 

[007wall]

liscensing is fine

 

[wireman50]

is port 17 working?

 

[007wall]

no, none of them, it has an ip address and the setting seem correct but absolutely no power to level 2

 

[wireman50]

so hard drive from another machine fires up the level 2 OK?. Your hard drive will not work on either controller? If so has to be time for a complete reinsatll or a new drive.

 

[kwbMitel]

How about DBMS Save?

I seem to remember that my systems didn't have power until this step.

**********************************************
What's most important is that you realise ... There is no spoon.

 

[007wall]

Yes to wireman 50 it looks like it. I will have ago DBMS saving. I don't think I did that.. Thanks everyone. If this doesn't work I'm gonna have to scrap it. I haven't got the time at the moment to keep working on this.

 

[007wall]

DBMS saving didnt make any difference

 

[Waldosworld]

Verify
The IP address of the L2 on the same subnet as the controller.
L2 ports set to ENABLES and PoE setting AUTO.

 

[007wall]

Log Type: Software
Log Number: 1041
Severity: Warning
Date: 2013/Jan/19
Time: 13:18:45
Source: IP Networking - MIPS
Description: MIPS not up, resetting L2 Switch subsystem...
Module: IP Networking - MIPS
File Name and Line Number: MIPSServiceProvider.cpp;803


Current Total POE Power Consumption: 9.2
Maximum POE Power Allowed: 120.0
RX timeout errors: 1
RX read errors: 0
RX other errors: 0
TX write errors: 0
Checksum errors: 9
Protocol errors: 0

pt cfg ena mode Cl Ohms mA Volts Watts Bdgt ps dny OL sht flt
-- --- --- ------ -- ------ ----- ----- ----- ----- -- --- --- --- ----
1 YES ON I-SAMP 0 26422 63.4 47.45 3.0 7.5 0 0 0 0 none
2 YES ON DISC_R 0 131070 0.0 2.27 0.0 0.0 0 0 0 0 none
3 YES ON I-SAMP 2 25132 60.4 47.51 2.8 6.5 0 0 0 0 none
4 YES ON DISC_R 0 131070 0.0 2.27 0.0 0.0 0 0 0 0 none
5 YES ON DISC_R 0 131070 0.0 2.18 0.0 0.0 0 0 0 0 none
6 YES ON DISC_R 0 131070 0.0 2.16 0.0 0.0 0 0 0 0 none
7 YES ON DISC_R 0 131070 0.0 2.21 0.0 0.0 0 0 0 0 none
8 YES ON DISC_R 0 131070 0.0 2.21 0.0 0.0 0 0 0 0 none
9 YES ON I-SAMP 2 25422 72.3 47.43 3.4 6.5 0 0 0 0 none
10 YES ON DISC_R 0 131070 0.0 2.14 0.0 0.0 0 0 0 0 none
11 YES ON DISC_R 0 131070 0.0 2.19 0.0 0.0 0 0 0 0 none
12 YES ON DISC_R 0 131070 0.0 2.37 0.0 0.0 0 0 0 0 none
13 YES ON DISC_R 0 131070 0.0 2.28 0.0 0.0 0 0 0 0 none
14 YES ON DISC_R 0 131070 0.0 2.17 0.0 0.0 0 0 0 0 none
15 YES ON DISC_R 0 131070 0.0 2.34 0.0 0.0 0 0 0 0 none
16 YES ON DISC_R 0 131070 0.0 2.26 0.0 0.0 0 0 0 0 none
----- -----
TOTAL: 9.2 20.5

*** PoE Status End ***

 

[TLDuk]

I had the same problem it was a corrupt drive reloaded software restored backup all was ok

If its not broke tweak it..