Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

No Caller ID

Status
Not open for further replies.

td1019

IS-IT--Management
Jul 3, 2007
169
US
I have a station in network-region 20 sending calls to trunks on region 30. I have set everything on the trunk group to send. In the trace I dont even see the station trying to send a number to the carrier. If the carrier was blocking it I would see the number at least being sent in my trace I would think. Is there some setting between network-regions that I am not aware of? I even went to page two of the station and set per station cpn - send calling number to Y.

The station has an entry in public unknown
NUMBERING - PUBLIC/UNKNOWN FORMAT
Total
Ext Ext Trk CPN CPN
Len Code Grp(s) Prefix Len
5 2 31 42358 10

TRUNK FEATURES
ACA Assignment? n Measured: both Wideband Support? n
Maintenance Tests? y
Data Restriction? n NCA-TSC Trunk Member:
Send Name: y Send Calling Number: y
Used for DCS? n Send EMU Visitor CPN? n
Suppress # Outpulsing? n Format: public
Outgoing Channel ID Encoding: preferred UUI IE Treatment: service-provider

Replace Restricted Numbers? n
Replace Unavailable Numbers? n
Send Connected Number: y
Network Call Redirection: none Hold/Unhold Notifications? n
Send UUI IE? y Modify Tandem Calling Number? n
Send UCID? y
Send Codeset 6/7 LAI IE? y Ds1 Echo Cancellation? n


List trac st 24xxx
12:41:59 dial 9xxxxxxx route:HNPA|ARS
12:41:59 term trunk-group 31 cid 0x27fc
12:41:59 dial 9xxxxxxx route:HNPA|ARS
12:41:59 route-pattern 31 preference 1 location 2/ALL cid 0x27fc
12:41:59 seize trunk-group 31 member 6 cid 0x27fc
12:41:59 Setup digits xxxxxxx
12:41:59 Calling Number & Name NO-CPNumber NO-CPName
12:41:59 G711MU ss:eek:ff ps:20
rgn:20 [10.139.200.205]:3246
rgn:30 [10.139.140.27]:3296
12:41:59 Proceed trunk-group 31 member 6 cid 0x27fc
 
run command change station xxxx goto page 2 and check value of PER STATION CPN-send calling number to YES
 
Already did that. Its in my initial post. I really think this is pointing back to the carrier but they are saying all is right on their side. I have requested a testing time with them so I can get a tech on their side to look at what I am sending to them. Other than that I cant find anything, I just thought there may be something in the data going between regions but I am grasping with that.
 
looking at ur trace... you don't need to worry abt line:

12:41:59 Calling Number & Name NO-CPNumber NO-CPName --> this is a station trace CLI will show on TAC...have you looked at tac trace?

can you post the TAC Trace as this will show what CLI CM is sending to your supplier. this should be 5 or 6th line on tac trace.
 
its pretty much the same thing

list trace tac 9031 Page 1

LIST TRACE

time data

08:26:21 dial 9xxxxxxx route:HNPA|ARS
08:26:21 term trunk-group 31 cid 0x364f
08:26:21 dial 9xxxxxxx route:HNPA|ARS
08:26:21 route-pattern 31 preference 1 location 2/ALL cid 0x364f
08:26:21 seize trunk-group 31 member 48 cid 0x364f
08:26:21 Setup digits xxxxxxx
08:26:21 Calling Number & Name NO-CPNumber NO-CPName
08:26:21 G711MU ss:eek:ff ps:20
rgn:20 [10.139.200.83]:3304
rgn:30 [10.139.140.30]:2740
08:26:21 Proceed trunk-group 31 member 48 cid 0x364f
08:26:28 idle station 2xxxx cid 0x364f
 
What is populated in your public numbering plan ??

APSS (SME)
ACSS (SME)
ACIS (UC)
 
Ext Ext Trk CPN CPN
Len Code Grp(s) Prefix Len
5 2 31 42358 10
 
There is more entries for other trunk groups but that is the one for this group
 
Apologies you actually stated this in your first post , Have you tried to manipulate this number to match the amount expected by the carrier ,sometimes i have had it where they are expecting a different number of digits than what they say(that said you should be seeing this in your trace i guess) Is this a pri circuit

APSS (SME)
ACSS (SME)
ACIS (UC)
 
Update this was an AT&T issue as I originally thought. They resolved it yesterday late afternoon and did not tell me what they did to resolve it.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top