No Caller ID Set shows 7925-1

[waynehamm]

Have a Meridian Option 11

What is required to get Caller ID information? I found a related post and have posted what they requested in order to help.

Location: Windsor, Ontario, Canada

>ld 60
DTI000
.stat

PRI* TRK LOOP 1 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
TRACKING
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : RED
CH 01 - DSBL TIE VOD * CH 02 - DSBL TIE VOD *
CH 03 - DSBL TIE VOD * CH 04 - DSBL TIE VOD *
CH 05 - DSBL TIE VOD * CH 06 - DSBL TIE VOD *
CH 07 - DSBL TIE VOD * CH 08 - DSBL TIE VOD *
CH 09 - DSBL TIE VOD * CH 10 - DSBL TIE VOD *
CH 11 - DSBL TIE VOD * CH 12 - DSBL TIE VOD *
CH 13 - DSBL TIE VOD * CH 14 - DSBL TIE VOD *
CH 15 - DSBL TIE VOD * CH 16 - DSBL TIE VOD *
CH 17 - DSBL TIE VOD * CH 18 - DSBL TIE VOD *
CH 19 - DSBL TIE VOD * CH 20 - DSBL TIE VOD *
CH 21 - DSBL TIE VOD * CH 22 - DSBL TIE VOD *
CH 23 - DSBL TIE VOD * CH 24 - DCH 15



>ld 96
DCH000
.stat dch
DCH 15 : DSBL RST AUTO DES : T1TIES


REQ ISSP

VERSION 2111
RELEASE 24
ISSUE 24 +

IN-SERVICE PATCHES : 10
PAT# PRS PATCH REF # NAME DATE FILENAME
00 MP01719 MPLR12019 r2bcs.11c 4/9/8 mp01719a.p
01 MP01719 MPLR12019 rebcs.11c 4/9/8 mp01719b.p
02 MP01974 MPLR12053 BERR in Traffic 4/9/8 mp01974.p
03 MP02029 mplr12048 SPN Corupn 4/9/8 mp02029.p
04 MP02232 MPLR12050 RTC 4/9/8 mp02232.p
05 MP02380 MPLR12091a TMDIpatchpart1 4/9/8 mp02380a.p
06 MP02380 MPLR12091b TMDIpatchpart2 4/9/8 mp02380b.p
07 MP02380 MPLR12091c TMDIpatchpart3 4/9/8 mp02380c.p
08 mp02385 mplr12085 Taurus Hfree 4/9/8 mp02385.p
09 MP03452 1 ld 30 Entopia 4/9/8 p12358.p

 

[GHTROUT]

You need PRI for your outside lines.

Not sure what you included below your question, but it looks like someone who couldn't make any calls.




~~~
GHTROUT.com | Get the Input/Output Manuals | Tek-Tips FAQs | Recent Replies

 

[Johnthephoneguy]

Looks like you have more trouble than just caller id, get that loop up!

JohnThePhoneGuy

"If I can't fix it, it's not broke!

 

[waynehamm]

GHTROUT" - I got the information that I thought was needed was from the following thread (Sorry forgot to add it)

http://www.tek-tips.com/viewthread.cfm?qid=1476392&page=10

"Johnthephoneguy" - The phone lines are working so I'm not sure why the Channels say disabled.

How can I tell what type of phone service I'm using if my loop is down?

 

[Johnthephoneguy]

Most likely you have other loops that are up taking your calls. Disable that loop and then enable it, should come up if there are no other issues, if there are, then you can troubleshoot that or work with your telco to take care of their end.

JohnThePhoneGuy

"If I can't fix it, it's not broke!

 

[GHTROUT]

The phone lines in loop 1 were not working when you did LD60 STAT. There is no question of that.




~~~
GHTROUT.com | Get the Input/Output Manuals | Tek-Tips FAQs | Recent Replies

 

[waynehamm]

So how do I find out what I'm currently using for outside lines?

 

[yyrkroon]

print a dnb of 7925, see what route that's referring too and run a ltm of that route to list the members

 

[GHTROUT]

Not sure what a DNB is gonna do. But here's how I'd find out what trunks I was using:

Go to LD 21 and REQ prt, TYPE rdb ROUT (hit enter for all)
Go to LD 21 and REQ ltm, ROUT (hit enter for all)

Now place an outside call, put it on hold and go back to it. The first series of numbers before the dash is the Route Access Code of the trunk route used.

Find the Route Access Code in the TYPE RDB printouts under the ACCD prompt - that's the route you used. Look for the corresponding trunks in the REQ LTM printout.

Then question why you have all the other trunks. Then learn BARS

http://www.ghtrout.com/bars/

and figure out how calls are "supposed" to go out.









~~~
GHTROUT.com | Get the Input/Output Manuals | Tek-Tips FAQs | Recent Replies

 

[GHTROUT]

yyrkroon, now I see what you mean, do a DNB on the ACCD. Good plan after all




~~~
GHTROUT.com | Get the Input/Output Manuals | Tek-Tips FAQs | Recent Replies