New system new tmdi CS1000E rel 5

[TETech]

I need to add this card I have no config right now

I have the card in cab 0 slot 2

I have done the ddb

In load 17 how do I add the card

cequ the dlop command do I just chose a loop and how do I refer it to the card in 0-2

 

[x11tech]

Depends on the issue & version you are running. In CS 1000 5.0 the TNB of the card is different than in CS 1000 4.5 (or earlier).

Perform the following:

>ld 22
PT2000 

REQ  iss

VERSION 4021 
RELEASE 5 
ISSUE 00 W  + 
IDLE_SET_DISPLAY NORTEL

IPMG  TYPE CSP/SW MSP  APP  FPGA BOOT   DBL1     DBL2

  4 0 MGC    AD38 AA06 AA04 AA12 AD27      N/A DSP2AA07
  8 0 MGC    AD38 AA06 AA04 AA12 AD27 DSP1AA07      N/A

REQ

Once we know the issue & version you are using, we can be more specific.

 

[911guru]

When you build this in LD 17 you will reference the l s c of the Loop on the MG_CARD line that comes up after the DLOP as seen below. Here I am building Loop 2 on 0 0 2:

MGTDS 
MGCONF 
MFSD 
DTDT 
DLOP 2 24 ESF
[b][COLOR=red]MG_CARD 0 0 2[/color][/b]
MODE PRI
TMDI YES
LCMT FDL
etc....

911Guru

http://pbx-e911.com

 

[TETech]

excellent thats what I finally got done how about the clock controller it is in loop 0 shelf 0 slot 2 my clock is in freerun as there is nothing connected does this look ok

ld 73
Req prt
TYPE ddb

MGCLK 0 0 2
PREF 0 0 2
SREF

TRSH 00
RALM 3
BIPC 2
LFAC 3
BIPV 3 2
SRTK 5 30
SRNT 15 3
LFAL 17 511
SRIM 1
SRMM 2


OVL000
>ld 60
DTI000
.ssck 0 0
ENBL
CLOCK ACTIVE
CLOCK CONTROLLER - FREE RUN
PREF - 2
SREF -
AUTO SWREF CLK - ENBL

 

[x11tech]

I must learn to read post titles more closely... /sigh

 

[johnpoole]

one prompt in param, then the dch then the rdb then the trunks.. then 96 and 60.. then take the rest of the day off

john poole
bellsouth business
columbia,sc

 

[911guru]

I think you just nee to do a TRCK PCK to get the clock to track in LD 60.

911Guru

http://pbx-e911.com

 

[yuvami]

you need to program the card at the since the loop 20, here is a table for a mapping:
for example if you have the card installed at the slot 2 at the cabinet with the superloop 0 shelf 0, then you need to program:

Digital loop 20 Channel 0-31 Superloop Shelf 0 Card 2
Here is an example of a printout


DLOP NUM DCH FRM TMDI LCMT YALM T1TE TRSH MG_CARD
PRI 022 23 ESF NO B8S FDL - 00 000 0 03
PRI2 MG_CARD
021 000 0 02
APVL
DTI2 MG_CARD
020 000 0 01
MISP MG_CARD