New PCM line creation problem

[Ghoulam]

Hi everyone

I have a TSW sp8 of 3 lim, running from 2007, 2 lims on the same site and the third one on a remote one, conected through a xDSL line, but in 2007 we configured only one junctor 3-0-00 to gsmult=0-6, I need now to add the second junctor line through 3-1-00 to gsmult=0-2.
here is the config now:
<gjlcp:lim=1;
GROUP JUNCTOR LINE CONNECTION DATA
EQU GS MULT NO GS CON LIM
1-1-00-0 0-4 1
1-0-00-0 0-0 1

END

<gjlcp:lim=2;
GROUP JUNCTOR LINE CONNECTION DATA
EQU GS MULT NO GS CON LIM
2-1-00-0 0-5 1
2-0-00-0 0-1 1

END

<gjlcp:lim=3;
GROUP JUNCTOR LINE CONNECTION DATA
EQU GS MULT NO GS CON LIM
3-0-00-0 0-6 1

END

<gjlsp:lim=1;
GROUP JUNCTOR LINE STATUS
EQU = 1-0-00-0 GS-MULT 0-0 MCCL
GS SIDE 0 ACTIVE ACTIVATED SIGNALLING MASTER LINK
SIDE 0 ALARM 0000 0000 0000 0000 GSMINPUT 11111110


EQU = 1-1-00-0 GS-MULT 0-4
GS SIDE 0 ACTIVE ACTIVATED SIGNALLING NO CLOCK CONTROL
SIDE 0 ALARM 0000 0000 0000 0000 GSMINPUT 11111110



END

<gjlsp:lim=2;
GROUP JUNCTOR LINE STATUS
EQU = 2-0-00-0 GS-MULT 0-1 RCCL
GS SIDE 0 ACTIVE ACTIVATED SIGNALLING CLOCK CONTROL
SYNC RECEIVING
SIDE 0 ALARM 0000 0000 0000 0000 GSMINPUT 11111110


EQU = 2-1-00-0 GS-MULT 0-5
GS SIDE 0 ACTIVE ACTIVATED SIGNALLING NO CLOCK CONTROL
SIDE 0 ALARM 0000 0000 0000 0000 GSMINPUT 11111110



END

<gjlsp:lim=3;
GROUP JUNCTOR LINE STATUS
EQU = 3-0-00-0 GS-MULT 0-6 ACCL
GS SIDE 0 ACTIVE ACTIVATED SIGNALLING CLOCK CONTROL
SYNC RECEIVING
SIDE 0 ALARM 0000 0000 0000 0000 GSMINPUT 11111110



END

the problem is when I try to create the new link between GJUL4 and GS, (3-1-00 and gsmult=0-2), I have this answer from the system:
<GJLII:EQU=3-1-00-0,GSMULT=0-2;
NOT ACCEPTED
LINK FAULTY ON BOTH SIDES

which is normal because I tried this without link, when I use the working link I have this answer:
<GJLII:EQU=3-1-00-0,CHL=32,GSMULT=0-2;

NOT ACCEPTED
NO ANSWER FROM GAR

Someone can help please?
Is there another command to use before GJLII?
why the system doesn't see the 3rd lim even when I use the same link used on gsmult=6, same cable, same xdsl link.
thanks in advance.

 

[Ghoulam]

here is other commands that may help:


<ilssp;
BPOS GSMULT SIGN LINK STATUS LINK CAPABILITY
001-0-00 0-00 YES OKAY LONG
001-1-00 0-04 YES OKAY LONG
002-0-00 0-01 YES OKAY LONG
002-1-00 0-05 YES OKAY LONG
003-0-00 0-06 YES OKAY LONG

<scicp;
MASTER LIM/GSM CONFIGURATION DATA
MASTER 2ND MASTER 3RD
LIM GSM LIM GSM LIM
1 0 2 3
END

 

[Ghoulam]

Ok guys problem resolved.

I had to erase the board and re-initiated again, and then the PCM line was created normaly

Sorry for the post.