Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

New Loop

Status
Not open for further replies.

oneeyebrow

Technical User
Mar 7, 2011
42
US
Hello,

I'm in the process of building QSIG PRIs in our systems. In other, older systems, I have been able to use existing Loop/Route/D-Channel information no longer in useand, for lack of a better term, reverse engineer the build. However, I have a site that does not have this. Here's the CEQU:

CEQU
MPED 8D
TERM
REMO
TERD
REMD
TERQ
REMQ
SUPL V020 V028 V036 V240
V248 N252
SUPC
SUPF
XCT
CONF
MGTDS IPMG IPMG_TYPE
024 020 0 MGC
032 028 0 MGC
040 036 0 MGC
MGCONF IPMG PORTS IPMG_TYPE
025 020 0 30 MGC
033 028 0 30 MGC
041 036 0 30 MGC
MFSD * 024 * 032 * 040

DLOP NUM DCH FRM TMDI LCMT YALM T1TE TRSH MG_CARD
PRI 001 24 ESF NO B8S FDL - 00 020 0 01
002 24 ESF NO B8S FDL - 00 020 0 02
003 24 ESF NO B8S FDL - 00 020 0 03
MISP MG_CARD
EXT0 3PE
EXT1 3PE
MCFN 011 MB

and here's the current STAT of MSDL cards:

.stat msdl 20 0 2

MSDL 020 0 2 ENBL
DCH 1 OPER PORT 0
DCH 2 OPER PORT 1
.stat msdl 20 0 4

MSDL 020 0 4 ENBL
DCH 3 OPER PORT 0

and here's the dch and dch map:

DCH 001 : OPER EST ACTV AUTO BKUP 002 DES : VERIZON_DID
DCH 002 : OPER EST STBY AUTO PRIM 001 DES : VERIZON_DID
DCH 003 : OPER EST ACTV AUTO DES : VERIZON_DID_ALT
DCH 021 : OPER EST ACTV AUTO DES : VIRTUAL_TRUNKS

DCH 001 : GROUP 03 MSDL 02 PORT 0 MSDL 02 PORT 0
DCH 002 : GROUP 03 MSDL 02 PORT 1 MSDL 02 PORT 1
DCH 003 : GROUP 03 MSDL 04 PORT 0 MSDL 04 PORT 0
DCH 021 : DCIP

My question is, can I build the QSIG PRI on 020 00 04 port 2? If yes, do I build it as loop 4/d-channel 4?

Any advice would be apprecaited. Many thanks.
 
As long as it is not in use for a media gateway (Check in 97). In CEQU at PRI promt enter 4 it will then prompt for the Loop Shelf Card of were the PRI is (This ties the loop 4 to the card), then fill out the other stuff (Frame etc.). Next build the DCH:

REQ chg
TYPE adan
ADAN new DCH 4
CTYP msdl
MG_CARD 20 0 4
PORT 2

When you get to doing your channels in LD14 it would be 4 1 upwards.
 
Thanks. Can you let me know what commands to use in LD 97 and what to look for.

Thanks again.
 
LD 97
REQ prt
TYPE supl
enter till it prints make sure loop 4 is not in there
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top