Network 2 Magix Point-to-Point dialing

[rmelan47]

I have 2 Magix networked with 6 plain e&m type tie lines, and using centralized VM.

I can dial between locations using UDP,and centralized VM works.


The main Magix has 12 channels for 2 way calling using tie lines (DNIS digits), then 6 channels for networking to other Magix. The remote Magix has only 6 channels used for networking.

Customer want to dial from remote Magix to make LD/local calls using main Magix trunks.


How do I set this up?

Thanks for any help

 

[merlinman]

The very basics to do this require the "OFF SITE" switch to have 9 in the "OTHER DIGITS" part of the ARS Table.

Also, your TIE LINES must be set for remote access in both systems.

It is a rather complex thing to set up, but it does work quite well.

http://home.comcast.net/~merlinman

 

[rmelan47]

Merlinman


Thanks for the quick answer.

I will add the 9 in the "OTHER DIGITS" of the ARS at remote Merlin with no trunks. The pools for all ARS tables should be 890, the same as UDP

NON-LOCAL DIALPLAN

Range Ptn Dgt Range Ptn Dgt Range Ptn Dgt
1) 200- 249 01 03 18) - 35) -
2) 444- 444 20 03 19) - 36) -
3) - 20) - 37) -
4) - 21) - 38) -
5) - 22) - 39) -
6) - 23) - 40) -
7) - 24) - 41) -
8) - 25) - 42) -
9) - 26) - 43) -
10) - 27) - 44) -
11) - 28) - 45) -
12) - 29) - 46) -
13) - 30) - 47) -
14) - 31) - 48) -
15) - 32) - 49) -
16) - 33) - 50) -
17) - 34) -

Pattern 1:

Pool Absorb Other Digits FRL Call type
1)890- 00 -------------------- 3 BOTH
2)---- -- -------------------- - -----
3)---- -- -------------------- - -----
4)---- -- -------------------- - -----

Pattern 20:

Pool Absorb Other Digits FRL Call type
1)890- 03 770----------------- 0 VOICE
2)---- -- -------------------- - -----
3)---- -- -------------------- - -----
4)---- -- -------------------- - -----


TABLE 27: Dial 0 Output Table

Pool Absorb Other Digits FRL Call type Start Pattern
1)890- 00 9------------------- 3 BOTH --:-- A
AUTOMATIC ROUTE SELECTION



TABLE 28: N11 Output Table
01)411 02)611 03)811

Pool Absorb Other Digits FRL Call type Start Pattern
1)70-- 00 -------------------- 3 BOTH --:-- A
AUTOMATIC ROUTE SELECTION



TABLE 29: E911 Table (911)

E911 Option: Partition

Allow-11: Disable

Other Digits for E911 calls redirected to Main Pool: --------------------

E911 Adjunct Trunks:

E911 Adjunct Alarm Extension:

Partition 1:
Extensions: 7100 7300 7101 7301 7102 7302 7103 7303
7104 7304 7105 7305 7106 7306 7107 7307 7108 7308
7109 7309 7110 7310 7111 7311 250 251 252 253
254 255 256 257 258 259 260 261 262 263
264 265 266 267 268 269 270 271 272 273
274 275 276 277 278 279 280 281
Trunks: 805 806 807
Other Digits: 9-------------------

 

[rmelan47]

Merlinman


One other thing about remote access in both Magix.


You are talking about going into programing under LinesTrunks = Remote Access = Tie lines = Restriction =
Unrestricted.

What about Non Tie lines Remote Access.

I will try this the first part of the next week.



Thanks

Ext NTM person from NJ

 

[merlinman]

Yup & Yup.

Same Pool, and yes on the Tie Line remote access.

Looks like you pretty much have it done.

http://home.comcast.net/~merlinman

 

[rmelan47]

Merlinman Thanks You.



When did you work in Denver?


I worked at NTM Manager (National Technical Marketing) in Parsippany,NJ in 1988-89.

I supported the small business products, was on product team for new a product called Partner 206.

The first Partner I saw was a Merlin Plus Control Unit being turned into a Partner by the Bell Labs folks writing code.

 

[merlinman]

I Retired from Avaya in Denver in 2001.

Last job was NTM Myself in Legend/Magix.

Tier-3 Tech Support Engineer before that.

For more info visit:

http://home.comcast.net/~merlinman