need to enable the automatic disconnect over Euro ISDN PRI when caller didn't hung'up the handset

[Optman]

Hi all

we have issue of automatic disconnecting of call over Euro ISDN PRI trunk, so when user end his call and let the handset didn't hung up the system didn't terminate it automatically.

Please see the rdb printout:
TYPE RDB
CUST 00
ROUT 20
DES PRI
TKTP DID
NPID_TBL_NUM 0
SAT NO
IDEF NET
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC EURO
CNTY FRA
SBN NO
PNI 00000
NCNA NO
NCRD NO
ISAR NO
CPFXS YES
SDID NO
DAPC NO
INTC NO
MBXR NO
MBXOT NPA
MBXT 0
DSEL VOD
PTYP DCO
CNDP UKWN
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 7000
TCPP NO
PII NO
AUXP NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
MFC NO
ICIS YES
OGIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640


PAGE 002

FLH 510
GTO 896
GTI 896
SFB 3
NBS 2048
NBL 4096

IENB 5
VSS 0
VGD 6
DTD NO
SCDT NO
2 DT NO
DDO NO
DRNG NO
CDR YES
INC YES
LAST YES
QREC YES
OAL YES
AIA YES
OAN YES
OPD YES
NDP EXC 0
CDRX YES
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS YES
MRT 34
MR NO
PANS YES
RACD NO
EQAR NO
FRL 0 0
FRL 1 1
FRL 2 2
FRL 3 3
FRL 4 4
FRL 5 5
FRL 6 6
FRL 7 7
OHQ NO
OHQT 00
TTBL 0
ATAN NO
PLEV 2
OPR YES
PRDL NO
EOS NO
DNSZ 0
RCAL NO
MCTS NO
ALRM NO
BTT 30
ACKW NO
ART 0
PECL NO
DCTI 0
TIDY 7000 20
SGRP 0
ARDN NO
CTBL 0
AACR NO

Please is there any solution for this ?


Thanks in advance

Regards

 

[Firebird Scrambler]

In the UK, we used to use the country type, but for the past 8 to 10 years it's been ETSI as shown in the example below.

LD 17

REQ CHG
TYPE ADAN
ADAN NEW DCH xxx Match PRI2 (Test data)
CTYP MSDL
GRP x (Test data)
DNUM xx (Test data)
PORT x 0 or 1
DES EURO_ISDN
DPNS NO
USR PRI
IFC E403
CNTY ETSI
PINX_CUST 0
DCHL xxx Match DCH (Test data)
RCAP COLP
RCAP ND3
RCAP NCT
REQ ****

LD 73 DIGITAL TRUNK INTERFACE

REQ NEW
TYPE PRI2
FEAT PAD
PDCA xx Increment PAD Value from 2
ONP 0 0
OPX 0 0
DTT 0 0
DCO 0 0
NTC 0 0
TRC 0 0
DTR 0
VNL 0 0
ACO 0 0
AFX 0 0
ADD 0 0
PRI 0 0
DSET 0 0
BRIL 0 0
BRIT 0 0
WRLS 0 0
REQ ****


LD 73

REQ CHG
TYPE PRI2
FEAT LPTI
LOOP xxx Match PRI2 (Test data)
MFF CRC
ACRC YES
ALRM ALT
CLRS 1
REQ ****

LD 16 ROUTE DATA BLOCK

REQ NEW
TYPE RDB
CUST 0 (CRF)
ROUT xxx (CRF)
DES xxx (CRF)
TKTP DID
DTRK YES
DGTP PRI2
MODE PRA
IFC E403
CNTY ETSI
DAPC YES
TBL 0
AUTO (NO) / YES (CRF)
DNIS (NO) / YES (CRF)
NDGT xxx (CRF)
DCRD (NO) / YES (CRF)
ICOG IAO / ICT/ OGT (CRF)
TRMB NO
ACOD xxx (CRF)
TARG xxx (CRF)
INST xxx (CRF)
IDC (NO) / YES (CRF)
DCNO xxx (CRF)
NDNO xxx (CRF)
DEXT (NO) / YES (CRF)
DNAM (NO) / YES (CRF)
DRNG YES
CDR (NO) / YES (CRF)
INC (NO) / YES (CRF)
LAST (NO) / YES (CRF)
TTA (NO) / YES (CRF)
ABAN (NO) / YES (CRF)
CDRB (NO) / YES (CRF)
QREC (NO) / YES (CRF)
OAL (NO) / YES (CRF)
AIA (NO) / YES (CRF)
OAN (NO) / YES (CRF)
OPD (NO) / YES (CRF)
OPA (NO) / YES (CRF)
MUS (NO) / YES (CRF)
MRT xxx (CRF)
MR ENDC (CRF)
FRL 0 0 (CRF)
FRL 1 1 (CRF)
FRL 2 2 (CRF)
FRL 3 3 (CRF)
FRL 4 4 (CRF)
FRL 5 5 (CRF)
FRL 6 6 (CRF)
FRL 7 7 (CRF)
PLEV 0
REQ ****

LD 14 TRUNK DATA BLOCK

REQ NEW xxx Number of entries (CRF)
TYPE DID
TN l c Loop channel (Test data)
DES xxx (CRF)
PCDA xx Increment PAD Value from 2
PCML A
CUST 0 (CRF)
NCOS 7
RTMB xxx yyy Route followed by 1st member (CRF)
NITE xxx (CRF)
ATDN xxx (CRF)
CLS DTN
REQ ****


All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[nortelvet]

Can you provide a print of the dch's involved here perhaps it is the T306 timer or MCT option enabled?

 

[NoypiToits]

Change the D-channel timer setting in "INC_T306 4 & OUT_T306 4"

ADAN DCH 1
CTYP MSDL
DNUM 10
PORT 0
DES SSIA
USR PRI
DCHL 2
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC EURO
CNTY ETSI
PINX_CUST 0
ISDN_MCNT 300
CLID OPT1
PROG NCHG
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID **
RCAP COLP
MBGA NO
OVLR NO
OVLS NO
T310 120
INC_T306 4
OUT_T306 4
T200 3
T203 10
N200 3
N201 260
K 7


Villareal

 

[Optman]

Hi

Many thanks for this replies, I will only change the setting ""INC_T306 4 & OUT_T306 4"" then it will work ? is this enough ?

Please see my DCH printout:

REQ prt
TYPE adan dch 100
ADAN DCH 100
CTYP MSDL
MG_CARD 000 1 01
PORT 1
DES
USR PRI
DCHL 20
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC EURO
CNTY FRA
PINX_CUST 0
ISDN_MCNT 300
CLID OPT1
PROG NCHG
CO_TYPE STD
SIDE USR
CNEG 2
RLS ID **
RCAP
MBGA NO
OVLR NO
OVLS NO
T310 120
INC_T306 120
OUT_T306 120
T200 3
T203 10
N200 3
N201 260
K 7

Thanks & regards

 

[NoypiToits]

yes this is the disconnect timer for your d-channel when the far end or near end hang-up


Villareal

 

[NoypiToits]

INC_T306 120, OUT_T306 120 = this setup is 120 seconds disconnect after the call.

Villareal