Name Display over QSIG

[agpham]

I currently have a IFC=ESGF TIE connected to a VOIP server. Dialplans show up correctly, however names do not display across. Under RCAP, I cannot set ND2 or ND3 with this IFC type. Is there an alternative solution to this? Or a recommended QSIG IFC ?



---

Andy Pham, ACS/Life Safety IT
Honeywell International, Inc.

 

[dlesap]

The other side may not used the same QSIG level protocol.
Try to enquiry about it.

 

[agpham]

The other side only has 1 qsig selection. Is there another IFC I can change on the Nortel side?

This is using a TMDI card with T1 PRI to Asterisk server.



---

Andy Pham, ACS/Life Safety IT
Honeywell International, Inc.

 

[dlesap]

The basic QSIG is ESIG or ISIG. These protocols doesn't support name display.
Then ESGF or ISGF
EGF4 or IGF4
E403 or I403

E is for ETSI
I is for ISO

You can try anyone depending on the software package your PBX have.

Which PBX is the other side ?

 

[agpham]

It is an Asterisk PBX. I will check with the developer of the QSIG protocol stack to determine which flavor of QSIG is employed. Will post update ASAP.

Is there a popular flavor? ETSI or ISO?

Any other ideas will be welcome....


---

Andy Pham, ACS/Life Safety IT
Honeywell International, Inc.

 

[johnpoole]

this is the code i use qsig to a ccm and names do work, both directions

http://www.tek-tips.com/viewthread.cfm?qid=1017219..

this is my rcap, using the same set back to a rolm switch

RCAP COLP NDI CCBI CCNI PRI DV3I CTI  QMWI

john poole
bellsouth business
columbia,sc

 

[dlesap]

In the RCAP did you try NDO for ESGF interface ?
For ISO interface choose NDI

 

[agpham]

Tried all the RCAP above including NDO and NDI, still no names.

Also I get SCH0531 when trying to add QMWI. This is message waiting indicator I assume and would be nice.

Any other ideas to try?????????????

Here is my ADAN print-out:

ADAN DCH 6
CTYP TMDI
CARD 04
PORT 1
DES VOIP
USR PRI
DCHL 4
OTBF 32
PARM RS232 DTE
DRAT 64KC
CLOK EXT
IFC ESGF
PINX_CUST 0
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE NET
CNEG 1
RLS ID **
RCAP COLP NDI CCBI CCNI PRI DV3I CTI
PR_TRIGS DIV 2 3
CNG 2 3
PR_RTN NO
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7


---

Andy Pham, ACS/Life Safety IT
Honeywell International, Inc.

 

[agpham]

OK, problem FIXED.

IFC=ISGF with RCAP=COLP NDI CCBI CCNI PRI DV3I CTI works!

In addition, how can I get QMWI to work? I'm getting SCH0531 when attempting. Here's what it says about SCH0531 which I don't understand:

SCH0531
Unable to match input with stored mnemonics. The RCAP prompt in overlay
=
16 has been answered NDS when QSUr QSIG GF are not accessible or with =
an inappropriate interface configured (e.g. Sl 1).=20
Action: Reconfigure accordingly.
Severity: Info


---

Andy Pham, ACS/Life Safety IT
Honeywell International, Inc.

 

[dlesap]

QMWI is for Rls 25.40 at least...

 

[agpham]

Is there another RCAP I can use to transmit MWI across the QSIG tie?

---

Andy Pham, ACS/Life Safety IT
Honeywell International, Inc.

 

[dlesap]

No RCAP.
Different possibilities :
1- Use the Outcalling of the Mail to a specific DN of the other side
2- Create a analog trunk between M1 and QSIG PBX. The Outcalling of the Mail will send a call to that rout. The other side may be programmed to "understand" that call

 

[dlesap]

You can use ACDN or Phantom DN. That the same result, but phantom DN can remotly call forward with a phone versus ACD NCFW can be changed by terminal access only...