Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

MX-ONE Messaging Voice v 7.9 and RightFax 9.3 1

Status
Not open for further replies.

Alex2013

Technical User
May 10, 2013
26
ES
Hi all,

I read a lot in this forum about configuring RightFax and voice messaging but I'm not able to.

I need to configure 1 lines, for example 40100.

Steps:
1º Create 40100 (analog extension for voice)
2º Create 40101 (analog extension for fax)
3º Create empty GH (GHGMI) with diversion to OneBox. i don't know how do. My OneBox have a Voice Mail Group Data 74500(I see with VMGEP) with 40 Generic Voice Mail Data. Help me with this step.

I trying to diversion 40100 to 74500 is correct?

Thank you.
 
Create a user in OneBox, e.g. 40100 and set in the Answering pane the fax number 40101.
Create a call_list or empty GH group in the MD110 or MX-ONE to point (CDINI) the voice mail group (VMGEP).
Forward or use CDINI for your calls to the extension 40100 (voice) to go to the OneBox.
The empty group with CDINI to the OneBox (74500) will transfer your fax calls to the extension 40101 (fax) to go to the OneBox first then to the RightFax. In the fax pane of the user 40100 in OneBox write the data for the user (e-mail etc.).
Then it works.

///doktor
____________________________________
 
Hi doktor,

I understand:

1º Create 40100 (analog extension for voice)
2º Create 40101 (analog extension for fax)
3º Create a user in OneBox, e.g. 40100 and set in the Answering pane the fax number 40101
4º Create a empty group with CDINI to the OneBox (74500)

so far I think is right

5º You say: "Forward or use CDINI for your calls to the extension 40100 (voice) to go to the OneBox.". ¿I create a diversion of 40100 to "the new empty GH create in step 4?

Thanks for you help doktor!
 
Yooh.
4º Create a empty group with CDINI to the OneBox (74500)

This means that you must initiate an empty GH group (GH group without members) and the number for this group should be 40101.
GHGRI is the command. Make a diversion to the OneBox goup number: 74500.
Then it works alright.


///doktor
____________________________________
 
Ok, this goes...

Now, when i send a fax to 40101 listen: "sorry, there aren't fax lines free. Try it later"

I created a user in OneBox (40100) and set in the Answering pane the fax number 40101 (type fax) and in the fax pane (routing) TCP:192.171.6.201/40100//40100. Automatically 40101 appear in Rightfax.

What can be happening?
 
Work Servers.

* You will need to configure 2 x Workservers for Telephony Server Routing to work. For testing, you can use Workservers 1 & 2 for this.

o WORKSERVER 1 - Enable Telephony Server Routing - Route Documents should be enabled. Enter the IP address of the OneBox Server in the server field and set the protocol to TCP/IP.
o WORKSERVER 2 - Enable Telephony Server Routing - DO NOT enable Route Documents, leave this unchecked. Enter the IP address of the OneBox Server in the server field and set the protocol to TCP/IP.
o Set the Service Account on the Workserver to use your RightFAX domain login account. Make sure you select the Load Users option to ensure your using the correct domain account.

AND:
An example of this for a OneBox server with an IP address of 192.168.1.1 with a FAX Routing CP of 5000 for Subscriber 1234 would be: TCP:192.168.1.1/5000//1234

Let me know if you need additional help.
Post some screen dumps - for further help.

///doktor
____________________________________
 
Hi doktor,

Yes, 192.171.6.201 is OneBox.

48414 is voice extension and 48415 the alternative (fax type)

I did what you said with workserver and the cp, look at the captures

tnxm.JPG


1jh2.jpg


78hr.jpg


hrwc.JPG



Let me know if you need more captures.

Thank you
 
Does it work?

Otherwise add two work servers - copy work server 1 settings to work server 3 and 4.
The IP address in the work server should be the OneBox IP address.

From the screen dumps it looks allright.

If i t still does not work - disable the firewall in both RightFax and OneBox.

///doktor
____________________________________
 
Just use Callprocessor 00000 for the RightFax.

Enter the Telephony Server routing information.
For Named Pipes use 'NP:servername/source-mailbox/source-password/dest-mailbox'
For TCP/IP use 'TCP:servername/source-mailbox/source-password/dest-mailbox'

TCP:192.171.6.201/00000/40100
This is: Ip address for OneBox/Callprocessor 00000 / OneBox user mailbox.

Now it should work...


///doktor
____________________________________
 
Hi doktor!

Now work!!! [peace]

I cloned the rightfax with a newly installed image with licensing and it worked at the time.

Thank you very much for your help [thumbsup2]

Pd: finally i used the CP 05000
Pd: i dont remenber the model, but the brooktrout have 4 analog channels.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top