Music on Wait & Voice Mail

[niine]

Hi, i'm sorry for my english...

I have to put the "Music on Wait" for the operator & the "Voice Mail" for the extensions in my MD110 BC11 SP11;
someone can help me about the boards & the configuration that i have to know?


thanks

 

[niine]

hey.... no one can help me?

 

[new2md]

Use any media player or CD player/ Digital MOH system. Put the output of device to TMU card (pin 25 &27) on your exchange. If you have more than one LIM make a series connection.
Hope it will work !

 

[lalrl]

for Integrated Voicemail (IVM) you need two boards: HDU7/1 and SPU2, a link-cable between theese boards and licenses. Such a combination supports 300 Mailboxes. You can start with a bundle of 100 MBX.

 

[rfpui]

Hi
Question For new2md
Are You sure this pins? Are this odd? In my opinion pins should be even 26 & 28


Some more info about MOH (Music On Hold)

1.
In some MD110 (old type) are installed TSU-T board. Music from external device should be connected to TSU-T board or TMU.
Pins in plug to connect music signal to TMU or TSU-T are this same but
TSU-T use upper half of board
and TMU use lower half of board
2.
If in LIM is installed more then one TMU MOH should be connected to board in lower magazine.
For example
TMU boards are in mag 0 and 2. Connect MOH to board in MAG 0.
TMU boards are in mag 1, 2and 3. Connect MOH to board in MAG 1.

 

[niine]

Thanks,

so for Integrated Voicemail (IVM) i need:
- HDU7/1
- SPU2
- link-cable between theese boards
- licenses

...and what i need for "Music on Wait" in the operator queue?

 

[summerdike]

Regarding musi in queue
(MOW=Music on Wait)


If Group Serv D3=1 then MOW is provided by TMU input 1 (MOH1) or input 2 (MOH2). Which input (1 or 2) depends on AS parameter 139. This is a system wide parameter which does a number of things that can be chosen by accumulating a number of values. If value 32 is chosen then "Music on Hold special Message shall be provided". This means that MOH2 (input number 2)is used for MOW for ACD/Hunt groups.
This way it is possible -for example- to use MOH1 for "normal" music on hold (for parking by normal extensions always MOH1 and never MOH2 is used) and MOH2 for ACD/Hunt groups.

If group Serv D3=2 then MOH is only provided after RVA message. This means that -for example- if a group has only repeat queue message programmed the MOH/MOW is played after the repeat queue message. The input (MOH1 or MOH2) is again dependent on AS 139.

Then BC11 came with continuous announcement...
The cont. ann. can have values 0-254 (BC12)
Cont. ann. is played -in a fully "RVA-equiped group"- after the group queue announcement and only interrupted by the repeat queue announcement.
Cont. ann. can be used as a normal announcement (values 1-250) but the cont. ann. values 251-254 are special kind of "announcements".
If cont. ann. 251 is chosen then MOH1 (on TMU) is used.
If cont. ann. 252 is chosen then MOH2 (on TMU) is used.
If cont. ann. 253 is chosen then MOH3 (on TMU) is used.
If cont. ann. 254 is chosen then silence is used.


Question:
Now what happens if group Serv D3=0 and in command RAGAI for example Cont=251 is used?
Answer:
MOH/MOW is played from input nr. 1 on TMU.

Question:
Now what happens if group Serv D3=0 and in command RAGAI for example Cont=252 is used?
Answer:
MOH/MOW is played from input nr. 1 on TMU.

Question:
Now what happens if group Serv D3=2 and in comand RAGAI for example Cont=251 is used?
Answer:
MOH/MOW is played from input nr. 1 on TMU after RVA message. If no rva is programmed for group then no MOW is played.

So the continuous announcement (CONT in RAGAI/RAGAC) programming overrides (for a great deal) the group (SERV) parameter.

Then finally:
Another two system parameters (154 and 177)state the way the TMU('s) are used.

AS 154, possible values 0 , 1 or 2.
Parval=0 no moh input used.
Parval=1 1 moh input used, meaning MOH1 (the bottom input on the board)
Parval=2 moh1 and moh2 used (the bottom 2 inputs).
I think default value for this parameter is 2. Leave it that way.
It is not possible to increase the PARVAL value of AS 154 after it has been changed to a lower value, unless the TMU board is removed and re-inserted.

AS parameter 177:
Selection of tone instead of music.
parval=0 input 1-3 are used for music
parval=1 channel 1 (MOH1) tone instead of music
parval=2 channel 2 (MOH2) tone instead of music
parval=3 channel 3 (MOH3) tone instead of music
parval=7 all channels (MOH1&&MOH3) tone instead of music

Remark:
MOH3 is only available if more then 1 TMU in a Lim.
MOH3 is placed on second TMU if parnum 154=2.
MOH3 is placed on third TMU if parnum 154=1.

Total picture in this table:

Parnum 154=0 Parnum 154=1 Parnum 154=2
1 TMU tone Moh1 on TMU 1. Moh1 and 2 on TMU1
2 TMU’s tone Moh 2 on TMU 2 Moh3 on TMU2
3 TMU’s tone Moh 3 on TMU 3 No Moh on TMU3


MOH1 is on 4A26 & 4A28 on the board.
MOH2 is on 4A18 & 4A20 on the board.
MOH3 is on 4A26 & 4A28 on 2nd or 3rd TMU board in LIM.

tmu 1 is tmu board with lowest number
tmu 2 is tmu board with next to one lowest number
tmu 3 is tmu board with next to two lowest number
example with 3 board in lim:
tmu 1 =bpos 2-0-10
tmu 2 =bpos 2-1-10
tmu 2 =bpos 2-2-10


Good luck!



______________________________
"Reload and Restart Requested
System Initiated"