Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

MSDL 0304 Error

Status
Not open for further replies.

kondalisa

MIS
Dec 21, 2008
75
Hi, it is CS1000M/81c rls 5.5. I am so oftenly get following MSDL error and PRI gets disabled and after few minutes enabling/disbaling it gets OK

MSDL0304 GROUP 0 MSDL 13 (2) 1911

MSDL0304 GROUP 0 MSDL 13 (2) 1926

ERR9032 3 28 14:55:09 6/05/2009

MSDL0304 GROUP 0 MSDL 13 (2) 1932

MSDL0304 GROUP 0 MSDL 13 (2) 1925

MSDL0304 GROUP 0 MSDL 13 (2) 1909

MSDL0304 GROUP 0 MSDL 13 (2) 1923

MSDL0304 GROUP 0 MSDL 13 (2) 1920

MSDL0304 GROUP 0 MSDL 13 (2) 1910

MSDL0304 GROUP 0 MSDL 13 (2) 1926

MSDL0304 GROUP 0 MSDL 13 (2) 1906

MSDL0304 GROUP 0 MSDL 13 (2) 1939

ERR5142 00000000 00000014

MSDL0304 GROUP 0 MSDL 13 (2) 1911

MSDL0304 GROUP 0 MSDL 13 (2) 1948

MSDL0304 GROUP 0 MSDL 13 (2) 1898

MSDL0304 GROUP 0 MSDL 13 (2) 1923

MSDL0304 GROUP 0 MSDL 13 (2) 1915

MSDL0304 GROUP 0 MSDL 13 (2) 1924

MSDL0304 GROUP 0 MSDL 13 (2) 1915

MSDL0304 GROUP 0 MSDL 13 (2) 1923

MSDL0304 GROUP 0 MSDL 13 (2) 1919

MSDL0304 GROUP 0 MSDL 13 (2) 1936

MSDL0304 GROUP 0 MSDL 13 (2) 1909

MSDL0304 GROUP 0 MSDL 13 (2) 1932

MSDL0304 GROUP 0 MSDL 13 (2) 1926

MSDL0304 GROUP 0 MSDL 13 (2) 1923

MSDL0304 GROUP 0 MSDL 13 (2) 1927

MSDL0304 GROUP 0 MSDL 13 (2) 1906

MSDL0304 GROUP 0 MSDL 13 (2) 1925

MSDL0304 GROUP 0 MSDL 13 (2) 1997

MSDL0304 GROUP 0 MSDL 13 (2) 1980

MSDL0304 GROUP 0 MSDL 13 (2) 1925

MSDL0304 GROUP 0 MSDL 13 (2) 1940

MSDL0304 GROUP 0 MSDL 13 (2) 1937

MSDL0304 GROUP 0 MSDL 13 (2) 1902

MSDL0304 GROUP 0 MSDL 13 (2) 1936

MSDL0304 GROUP 0 MSDL 13 (2) 1936

MSDL0304 GROUP 0 MSDL 13 (2) 1910

MSDL0304 GROUP 0 MSDL 13 (2) 1919

MSDL0304 GROUP 0 MSDL 13 (2) 1930

MSDL0304 GROUP 0 MSDL 13 (2) 1922


DTI000
.****
OVL000
>*******
DTA301 34

MSDL0304 GROUP 0 MSDL 13 (2) 1935

DTA301 35

MSDL0304 GROUP 0 MSDL 13 (2) 1930
ld 96
MSDL0304 GROUP 0 MSDL 13 (2) 1923

DCH000
.du
DCH009


.dis dch 29
.
dis dch 29
DCH2023 29 3

.****
OVL000
>*******ld 60
DTI000
SL-1 --- SYS-12/AXE-10 SWE/NUMERIS/SWISS/TCNZ
/EUROISDN/SING/THAI/MSIA/INDO/CHNA
/INDI/PHLP
CHANNEL TIMESLOT MAPPING

.
SL-1 NETWORK TIMESLOT
B-CHANNEL 1 -15 1 -15 1 -15
16-30 17-31 17-31
D-CHANNEL 31 16 16
disl 29

OK
.

DTI000
.****
OVL000
>
OVL000
>err msdl0304
>

MSDL0304 x y
The Meridian 1 received 100 or more messages from MSDL x within two
seconds. At this level of message transfer, there may be some impact
to the overall system performance. The level of service does not
warrant removing the card from service. Where: x = device number (LD17
DNUM) y = the rate of message transfer from the card to the Meridian 1,
in terms of messages per second.

Severity: Major


Any help ??
Regards

 
I've had this when the DCH goes into a Cisco Call Manager. The problem was the Cisco box.

[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators
 
Hi GH, it is a TELCO PRI and it is use mainly for incoming calls. Any more suggestions??
 
During a maintenance window, I would disable the loop, DCH, and MSDL card. Reseat the MSDL card and then re-enable everything. 9 times out of 10, that clears MSDL errors.

War Eagle!
Lions Baseball '09!
 
prior to the MSDL error, did you happen to see any ERR5132's?

If so, you most likely have a CDP looping issue. Err5132 is formatted like:

ERR5132 0(Cust #) 1(Inc Route) 1(Out Route) XXXX(DN)

If you then go to LD 87 and out the CDP entry that is giving you problems, you'll then be able to eliminate the MSDL0304's.
 
Also I would force download the msdl card. This ensures a good download !! enl msdl x fdl.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top