Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Moving Card to new Slot 1

Status
Not open for further replies.
Nov 4, 2016
18
US
I've recently inherited a Nortel CS1000. It's been a few years since i worked on one and i'm a bit rusty. hoping someone can point me in the right direction.

I have 2 separate cs1000 stacks. One of them has been out of service for awhile. I have a new building that is being built, and i want to put the spare stack in place. I've got networking in place to support it. I'm really only interested in using it as an analog gateway.

Everything is working as it should, i can fire up the switch and get dial tone and make calls.

My query is this. there are 2 cabinets in the stack, Cabinet 1 has the processor card in slot 1, and no other cards. Cabinet 2 has an analog line card in Slot 7, and no other cards.

I want to take the card out of slot 7 and move it to slot 2. I'm doing this in order to save space in my already limited rack.

If i remember correctly i need to OUT all of the lines and the card, then run a command to move it... but for the life of me i cannot remember how. With my old Nortel i had a wall of all the manuals to reference, with this one i have nothing.

Any pointers would be appreciated.

Thank you.
 
Yes, it's best to capture all the line data in slot 7 and then delete it by using the command

>LD 14
REQ OUT 8
TYPE COT
TN 7 0 (Use the first TN on the card)

Assuming that all the COT trunks are using the same route and in order, then use NEW 8 in LD 14.

Firebird Scrambler
Nortel and Avaya Meridian 1 / Succession and BCM / Norstar Programmer

Very advance high level knowledge on the Linux BCM phone system.

Website
 
I didn't think the MOV command worked for trunks from one card to another, but only on the same card.

Firebird Scrambler
Nortel and Avaya Meridian 1 / Succession and BCM / Norstar Programmer

Very advance high level knowledge on the Linux BCM phone system.

Website
 
I am trying to move an Analog Card. I'm having some difficulty with this. I believe it may have to do with the fact that this system is on a different loop. It's listed as loop 8, but when i list the loops in my switch i do not have 8.
 
This is what i get when i try to mov via ld 25

REQ mov
CUST 0
SRCL 8
SCH5235


The cabinet does show 8 on the card.

*edit. specified that i tried to mov via ld 25
 
So i've been doing a bit more investigation into this which might help shed light on my problem.

the cabinets i'm working with are part of a Media Gateway Controller that is separate from my primary PBX which i am logging into.

I can login to the secondary media gateway controller as Admin, however i am left with an OAM prompt, which i'm not familiar with.
 
You shouldn't be logging into the MGC card. Log into the Call Server and do what Mike suggests
 
Mikepbxb, Thank you very much. your trick regarding leaving the customer blank was just the ticket.
The card has been moved. I'm adding my output below for future admin's having similar problems.

REQ mov
CUST
SRCL 8
DSTL 8
SHCD 0 7 to 0 2
SHCD

FORCED DISCONNECT SOURCE
FORCED DISCONNECT DESTINATION
SCH5524 DN 5557 NEW MARP 008 0 02 01
SCH5524 DN 2656 NEW MARP 008 0 02 02
SCH5524 DN 5580 NEW MARP 008 0 02 03
FORCED RE-CONNECT SOURCE
FORCED RE-CONNECT DESTINATION



 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top