Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

MOH How to check individual port status

Status
Not open for further replies.

Magillicuddy

IS-IT--Management
Nov 20, 2006
309
US
Is there a command or way to check the physical port or board status the music source is connected to? Like if you busy out and released a station or trunk, I was wondering if you could do this for the analog board or port.



thanks
 
This is the only way i can think of Magillicuddy. This will at least let you see that is working and what port you connected to.

Below I called another set in my office and put that call on hold while doing a "li trace sta xxxxx"


Code:
                                LIST TRACE

time            data

08:14:58     active station    57xxx cid 0x2ed
08:14:58     tone-receiver     02B0002 cid 0x2ed
08:14:59     dial 53000
08:14:59     ring station    53000 cid 0x2ed
08:15:04     active station    53000 cid 0x2ed
08:15:05     hold station    53000 cid 0x2ed
08:15:05     hear moh port 03A17003



When is the last time you helped someone, just because you were able to?

For the best response to a question, read faq690-6594


 
Mikeydidit

thanks, I tried that on CM ver 2,2 results was similar to your's but the line hear MOH port xxxxxxxx does not display. it pumps in a line about jitter and PKloss.

09:41:41 active station 3555 cid 0x98a
09:41:41 xoip: fax:pT modem:pT tty:US uid:0x8a6a cid:0x98a
09:41:42 dial 3444
09:41:42 ring station 3444 cid 0x98a
09:41:42 xoip: fax:pT modem:pT tty:US uid:0x8c8b cid:0x98a
09:41:43 active station 3444 cid 0x98a
09:41:46 hold station 3555 cid 0x98a
09:41:46 xoip: fax:pT modem:pT tty:US uid:0x8c8b cid:0x98a
VOIP data from: 172.22.96.23:33080
09:41:51 Jitter:0 0 0 0 0 0 0 0 0 0: Buff:8 WC:1 Avg:0
 
You can call the MOH port directly.

Use the command disp sys fea to obtain your current MOH port - [tt] Music/Tone on Hold: music Type: port 01E1401[/tt]

Then find out what your feature access code is for Facility Test Calls - [tt]Facility Test Calls Access Code: *05[/tt]

Dial the MOH port directly, using the FAC and the port. For the carrier, 01=A, 02=B, 03=C, etc. In my case, my MOH speed dial is
[tt]*05 01 05 14 01[/tt]

Susan
Muffins are just ugly cupcakes.
 
If you have Vectoring enabled in your switch, you can create VDNs that point to a vector similar to below. In one of my switches I have 8 different music sources for different tenants. I have a test music VDN for each tenant pointing to the common vector. Works great.

Kevin

CALL VECTOR

Number: 991 Name: MOH Test
Multimedia? n Attendant Vectoring? n Meet-me Conf? n Lock? n
Basic? y EAS? y G3V4 Enhanced? y ANI/II-Digits? y ASAI Routing? y
Prompting? y LAI? y G3V4 Adv Route? y CINFO? y BSR? y Holidays? y
Variables? y 3.0 Enhanced? y
01 wait-time 999 secs hearing music
02 goto step 1 if unconditionally
03 stop

VECTOR DIRECTORY NUMBER

Extension: 83991
Name*: Tenant 1 MOH Test
Destination: Vector Number 991
Attendant Vectoring? n
Meet-me Conferencing? n
Allow VDN Override? n
COR: 1
TN*: 1
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top