Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Mobile Twinning with original A-number
- Thread starter AvayaSpec
- Start date
hairlessupportmonkey
IS-IT--Management
nope - but its also telco dependant. you will need to see if they allow off switch calling party number presentation.
kflounders
Programmer
In USA it is carrier specific. Some like XO and PaeTec allow it and others like Broadview do not.
Kevin Flounders
Kevin Flounders
mattKnight
Programmer
>If you are in the UK you will not be able to do this because the telco prevents this
Depends on your carrier actually...
By default, the carriers will restrict you to showing numbers that terminate on the circuit that teh call originates from. However if you enter a contractual arrangement for type 4 CLI presentation you will be able to show outbound CLI for tandem calls. The carrier I use for ISDN have done this for us, but I guess you'd have to chase your BT account manager quite hard to get this.
As for SIP - the same applies - if you have the right provider, they will, again under a contractual agreement release CLI to PSTN to allow you to present tandem calls with the originating CLI
Take Care
Matt
I have always wished that my computer would be as easy to use as my telephone.
My wish has come true. I no longer know how to use my telephone.
Depends on your carrier actually...
By default, the carriers will restrict you to showing numbers that terminate on the circuit that teh call originates from. However if you enter a contractual arrangement for type 4 CLI presentation you will be able to show outbound CLI for tandem calls. The carrier I use for ISDN have done this for us, but I guess you'd have to chase your BT account manager quite hard to get this.
As for SIP - the same applies - if you have the right provider, they will, again under a contractual agreement release CLI to PSTN to allow you to present tandem calls with the originating CLI
Take Care
Matt
I have always wished that my computer would be as easy to use as my telephone.
My wish has come true. I no longer know how to use my telephone.
- Thread starter
- #7
I work in a Telecom Company and vi can se in the MGC that we can show it via CDR , but if we try on the IPO500 it will only show the main number, and this is both if we make the SIP like a Trunk or Account.
I think that it is Avaya IPO 500 that can’t handle A –B – and – C numbers on SIP. Remember there is no problem with this issue when we are on the PSTN
I think that it is Avaya IPO 500 that can’t handle A –B – and – C numbers on SIP. Remember there is no problem with this issue when we are on the PSTN
hairlessupportmonkey
IS-IT--Management
SS - Pass Through Calling Number
Pass through the Calling Party Number. For example, to provide the incoming ICLID at the far end of a VoIP connection, a short code ? with telephone number .SS should be added to the IP line.
Pass through the Calling Party Number. For example, to provide the incoming ICLID at the far end of a VoIP connection, a short code ? with telephone number .SS should be added to the IP line.
hairlessupportmonkey
IS-IT--Management
S - Calling Number
Place any following digits into the outgoing call's calling number field.
• Outgoing CLI Warning
Changing the outgoing CLI for calls requires the line provider to support that function. You must consult with your line provider before attempting to change the outgoing CLI, failure to do so may result in loss of service. If changing the outgoing CLI is allowed, most line providers required that the outgoing CLI used matches a number valid for return calls on the same trunks. Use of any other number may cause calls to be dropped or the outgoing CLI to be replaced with a valid number.
• Changing the outgoing CLI on calls using SIP trunks is not supported.
• On mobile twinned calls, if the original party information is used or a specific calling party information CLI is set, that number overrides setting the outgoing CLI using short codes.
Place any following digits into the outgoing call's calling number field.
• Outgoing CLI Warning
Changing the outgoing CLI for calls requires the line provider to support that function. You must consult with your line provider before attempting to change the outgoing CLI, failure to do so may result in loss of service. If changing the outgoing CLI is allowed, most line providers required that the outgoing CLI used matches a number valid for return calls on the same trunks. Use of any other number may cause calls to be dropped or the outgoing CLI to be replaced with a valid number.
• Changing the outgoing CLI on calls using SIP trunks is not supported.
• On mobile twinned calls, if the original party information is used or a specific calling party information CLI is set, that number overrides setting the outgoing CLI using short codes.
IPOfficeIreland
Technical User
don't use ss or anything like it on sip trunk route codes.
create a URI with *, *, * in Auth name, etc. Give it a different outgoing trunk group. set all twinned calls, forwarded calls, etc to route via this group.
create a URI with *, *, * in Auth name, etc. Give it a different outgoing trunk group. set all twinned calls, forwarded calls, etc to route via this group.
- Status