Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

MITEL L2 switch enabled.How to disable? 2

Status
Not open for further replies.

xxshow

Technical User
Aug 21, 2009
29
MITEL L2 switch enabled.Icp in continueous boot.Can't log on.How do I disable it.Communication down.URGENT ASSISSTANCE SOUGHT.
 
Oops should have put this in before the possible resolve:

Connecting the Maintenance PC to the
Controller

1. Connect an RS-232 straight DTE male to female serial cable between
the controller’s Maintenance port and the PC’s serial port (cable not
provided).

2. Program the PC’s serial port (from the communication program) with
the following settings:
- Baud Rate: 9600
- Data Bits: 8
- Parity: None
- Stop Bits: 1
- Flow Control: None

3. Connect a straight-through Ethernet cable (RJ-45) from the controller
leftmost Ethernet port (port 17 on the CXi; port 1 on the MXe) and the PC’s network interface card (NIC).

4. Program the PC’s NIC with the following settings:
- IP Address: 192.168.1.n (where n is a value between 30 and 254)
- Subnet Mask: 255.255.255.0

But I'm suspecting he got it fixed.
 
JimSmith & Bigsin thank you so much for your help my ICP is up & running you are each getting a star from me however my 5550ip console is still not getting an ip address from the ICP.Would love your input on this one too.
 
Very glad we could help. I know how much pressure is on when its not working and the staff are starting to light the torches and haul out the pitch forks :)

Thanks for the star, its my first one!!

Jim

 
Hi, ok I got these possible cures from the manual, check them out:

Troubleshooting IP Console Problems

To troubleshoot 5550 IP Console Problems
1. Go through Table 47 below.
2. If you cannot solve the problem using Table 47, go through the steps in “Generic Troubleshooting Steps” on page 144.
3. If you still can’t find the problem, call Mitel Networks Technical Support (see “Before You Contact Technical Support” on page 142).
Note: To rule out DHCP problems, and isolate network-related issues, we recommend that you program the IP Phone with a static IP Address (see TSB # 58004933).

Table 47. Troubleshoot IP Console Problems

Symptoms
IP console fails to register (red LED is lit on TKB).

Probable cause

TKB (keyboard) does not have a reserved IP address. OR TKB does not have the right IP addres.OR TKB is not communicating to the right Controller.

Corrective Action

1. Check DHCP lease to confirm if an expected IP address is assigned to TKB.
2. If not assigned properly, ensure that you enter the MAC address of TKB properly in the Multiline Set Assignment form in ESM.
3. Recyle the power of TKB to ensure that TKB is reloaded properly

Symptoms
IP console fails to register (red LED is lit on TKB).

Probable cause
Console PC does not have the proper IP address.

Corrective Action
If IP address of PC is on different subnet than TKB, make sure that the router between these two subnets is functional.

Symptom
IP console fails to register (red LED is lit on TKB).

Probable Cause
PC NIC has 802.1Q enabled on Data side while L2 switch is not configured to accept tagged frame on Native VLAN.

Corrective Action
Disable 802.1Q on PC NIC
Note: Only use 802.1Q on PC if PC and TKB are on the same vlan (e.g 2) which L2 switch accepts tagged frame on the specified VLAN.

Symptom
IP Console fails to launch

Probable cause
IP Console has been registered and IP console is reinstalled.

Corrective Action
Delete the MAC address from IP console form and then re-register using the IP Console Configuration Wizard (Start/MN5550 IP console/Tools).
Note: Do not re-run the IP Console software installation unless you need to (new installation, repair corrupted software, etc.). You should always use the Configuration Wizard to register to a different Controller.
 
What was the solution for your problem?

still the VLAN_OFF command or was it something different?
 
vlan_off command.Then webbed the ICP & disabled the L2,then command vlan_on,followed by command reboot.
5550ip console still challenging.
 
What was the reason why you couldn't connect to the Mitel after the first try using the command VLAN_OFF?

See your other topic about 5550 console for more tips.
 
JimSmith how about you send me the whole of your manual?
 
Hi, ok sent, also if you have the CD for your system, those (and possibly some more .pdfs) should be on it.

Jim
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top