Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

MiCollab 6 USP - MAC Address already exists in the system

Status
Not open for further replies.

bribob

Technical User
Jun 1, 2007
170
CA
vMiCollab 6.0.41.0

I'm attempting to manually provision a user in MiCollab. I am able to create the user but I encounter an error when entering the MAC address of the phone.

'Create Phone Service Error. The MAC Address already exists in the system'

I have checked the MCD, the MAC address is not in use. I have manually built the phone in MCD and successfully assigned the MAC address, which tells me that the MCD is not the source of the error. I suspect that a user already exists in USP, that this MAC address is assigned to.

There must be a way to check the postgres DB within MiCollab to see which user/phone has this MAC address assigned, does anyone know where I should start looking? Is there a CLI command that will dump the entire USP DB, not just the username/email/DN/services list?


-b
 
Oh my!

Is it possible the Mac is on a different system?

Have you / can you program without the MAC, I don't think I ever bother as I prefer PIN registration.

**********************************************
What's most important is that you realise ... There is no spoon.
 
That's what I suspected, so I started my investigation by logging into all MCDs in the cluster and checked, didn't find the MAC address.

I disabled Single Point Provisioning and the error remained. I was also able to manually configure the DN/MAC in the MCD it was accepted, so the phone could technically register and all would be well, except that I would know there is a disturbance in The Force (MiCollab and MCD DB out of sync).

I found the MAC address in the UPM/current log, below is the reference to the error:

UPM: pgSQLObj.cpp(589): pgSQLObj.cpp: INSERT INTO msvc_ICP3300PhoneServiceDataList (output omitted / details about the phone)
UPM: pgSQLObj.cpp(608): pgSQLObj.cpp: Unable to insert child (msvc_ICP3300PhoneServiceDataList): - ERROR: duplicate key value violates unique constraint "u_msvc_icp3300phoneservicedatalist_macaddress"
UPM: pgErrorObj.cpp(141): pgErrorObj.cpp: *** Found duplicate key string
UPM: pgErrorObj.cpp(156): pgErrorObj.cpp: duplicate key value violates unique constraint "u_msvc_icp3300phoneservicedatalist_macaddress"
UPM: pgErrorObj.cpp(168): pgErrorObj.cpp: Extracted constraint name
UPM: pgErrorObj.cpp(169): pgErrorObj.cpp: u_msvc_icp3300phoneservicedatalist_macaddress
UPM: PostgresAdapter.cpp(3248): PostgresAdapter.cpp: PGAdapter: Rollback Successful


Yes, I know I should have paid more attention in Database class.


-b
 
To answer your question, yes I can add the DN to the user in MiCollab without the MAC address.


-b
 
But adding without mac affects other applications?

**********************************************
What's most important is that you realise ... There is no spoon.
 
does it have an entry in the teleworker database

If I never did anything I'd never done before , I'd never do anything.....

and due to an endless stream of MiCollab , MiCC issues
Life would be simpler If only they tested products properly before releasing them .....
 
@kwb - Added the phone without MAC, have also assigned NuPoint mailbox, MDuG, TW service w/o MAC

@Bill - Checked the Teleworker DB in MiCollab and the 2 MBG's in the cluster. No MAC found


-b
 
the mac is programmed in the teleworker ...
delete it in the MBG.. and it should work fine
 
Mitel TS took a backup of the MAS DB and used a tool to find the offending MAC assigned to another user. It would appear that the MBG DB and USP DB are separate.


-b
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top