Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Message Waiting Lamp across PRI

Status
Not open for further replies.

lazycalm

Technical User
May 27, 2008
23
US
I have two sites, one an Opt. 11, the other a 61 with an AVST Voice Mail System. The two sites are connected with a PRI.

I would like to put the Opt.11 users on the AVST, but I'm not sure how to relay the MWL request through the PRI to the Option 11. Is this even possible? Is there another way to do it?

I should also add that I'm currently using Mermail at the 11 site. And, I should also add that I would like to put the AVST in one of those machines that smashes cars and replace it with a Call Pilot, but that's not in the cards right now.
 
You have to have the network messaging package and the PNI must match at both ends. CDP takes care of the routing.

Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.
 
Checked the packages. Both switches have NMS - 175, PNI is set to zero at both ends, still no MWL.

There's another problem: The voicemail recognizes my number, so I know that part is working, but if I call forward my phone, the opt. 11 sends the 61 the digits of the incoming caller - which obviously won't route it to my VM box.
 
RCAP on the dchannel has MWI?

Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.
 
Doesn't appear to be. Would I just program RACP QMWI on the route? Here's the existing programming:

TYPE RDB
CUST 00
DMOD
ROUT 20
DES TIE TO MEM
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC SL1
PNI 00000
NCNA YES
NCRD NO
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
DAPC NO
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 707
TCPP NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096
TFD 0
DRNG NO
CDR YES
INC YES


PAGE 002

LAST YES
QREC NO
OAL YES
AIA YES
OAN YES
OPD NO
NATL YES
MUS NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO
 
Make sure the value of PNI is the same at both ends and is NOT equal to 0.
 
OK - Yes I see in the book that PNI=0 will disable NMS. I changed PNI=1 at both sites (all circuits). It still will not light the lamps.
 
First thing is put a message indication key on your set and then try to turn on a light at the far end. monitor the dchannel messages and you sould see a nms message go across.

Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top