MERIDIAN OPTION 81C CODE BAD - ERROR IOD 041

[CALPHONELADY]

HI. PBX ON LAST LEGS, BAD CORE, WENT DOWN HARD TODAY.
PBX IS BACK UP BUT WITH ISSUES.
SO MAY ERRORS GETTING IOD 041. HOW DO I CLEAR IT TO SEE THE ALARMS? MY HOPE IS THAT MOST OF THE ERRORS/BUGS THAT FILLED THE BUFFER HAVE CLEARED BUT THAT MAY BE WISHFUL THINKING.
INFO GENERATED NOW MAY PROVIDE GUIDANCE ON WHAT TO CHECK/FIX NEXT.
CURRENTLY DIAL TONE WORKING, CALLS OUT&IN, PRIs GOOD, BRIs GOOD.

NEED TO CONFIRM WHAT TO DO FOR "SYNC" ISSUE BELOW. AND THAT THE FIX HOPEFULLY WON'T CAUSE ADDITIONAL ISSUES TRYING TO RE SYNC. ANY INFO ALWAYS APPRECIATED.
THANKS

LD 137
STAT
IOP 0 ENABLED (ACTIVE) IODUC
IOP 1 DISABLED (No Response)
IOP-CMDU
CMDU 0 ENABLED (ACTIVE)
CMDU 1 DISABLED (Not in SYNC)
RDUN DISABLED
ELNK ENABLED
SDEV 0 OK (KC VALID)

 

[Firebird Scrambler]

USE THE FOLLOWING PROCEDURE.
CHECK WHICH IS ACTIVE CP AND ACTIVE CMDU
IF FOR eg CP 0 ACTIVE CMDU 1 ACTIVE (CMDU 0 DSBL) OR VICE VERSA
1st) GET BOTH ACTIVE CP AND CMDU ON SAME SIDE ie LD 135 SCPU
so in our eg CP1 active CMDU 1 active
2nd) PUT SWITCH INTO SPLIT MODE by(THE FOLLOWING ORDER MUST BE FOLLOWED OR ELSE!)
a) THROW NORM/MAINT SWITCH TO MAINT ON ACTIVE CP(our eg CP1)
************
b) NOW THROW NORM/MAINT SWITCH TO MAINT ON STANDBY(inactive) CP
c) NOW DISABLE THE CNIs ON THE STANDBY (inactive) CP

THE SWITCH IS NOW IN SPLIT MODE CAN BE CONFIRMED BY STAT IN LD 135
************************************************************************************************************************************
NOW ON STANDBY CP
1) PRESS MAN RST BUTTON ON CP (AND WATCH DISPLAY AND WHEN YOU SEE SYS700 ON LCD DISPLAY)
2) RESTORE MTCE/NORM SWITCH BACK TO NORM
************************************************************************************************************************************
ON TTY YOU SHOULD NOW SEE.....' MEMORY SYNC BEGUN'
WHEN YOU SEE SYNC MEM COMPLETE
a) RESTORE MAINT/NORM SWITCH ON ACTIVE CP TO NORM
b) ENABLE CNIs ON INACTIVE CORE
b) LOGIN & LD 137 AND TYPE STAT, THEN TYPE SYNC
WHEN THIS COMPLETES YOU CAN STAT AND BOTH CMDU's WILL BE ENBL'D
AND REDUNDANCY ENBL'D

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website =

http://somertel.myfreesites.net

linkedin

 

[CALPHONELADY]

HI. THANK YOU FOR GETTING BACK TO ME. I'VE NOT SPLIT MODES BEFORE BUT WILL BE WORKING WITH FORMER NORTEL TECH. NEED TO GET YOU HERE WITH US.

I'M LOOKING AT THE CNIs RIGHT NOW. I GET THE BELOW WHEN I STAT.
DOING TEST DIAGNOSTIC, IN CASE CNI CARD BAD.
ANY INFO YOU CAN SHARE IS GREAT.
THANKS!

cni 1 12 0: remote = group 3 ENBL
cni 1 12 1: remote = group 0 ENBL
cni 1 13 0: remote = group 1 ENBL
cni 1 13 1: remote = group 2 ENBL

cni 0 12 0: remote = group 3 DSBL: 'NOT RESPONDING'
cni 0 12 1: remote = group 0 DSBL: 'NOT RESPONDING'
cni 0 13 0: remote = group 1 DSBL: 'NOT RESPONDING'
cni 0 13 1: remote = group 2 DSBL: 'NOT RESPONDING'

 

[CALPHONELADY]

CNIs REPLACED AND ENALED

WHEN GOING THRU PROCESS AND GET TO THE BELOW, LD 135 DOES NOT SHOW US IN SPLIT MODE
STATTED CPU, MEM, AND CNI AND NO INDICATION OF SPLIT MODE
INACTIVE CNIs SHOW ENABLED EVEN THOUGH WE DISABLED AT THE CARD.
WHAT DID I MISS?


USE THE FOLLOWING PROCEDURE.
CHECK WHICH IS ACTIVE CP AND ACTIVE CMDU
IF FOR eg CP 0 ACTIVE CMDU 1 ACTIVE (CMDU 0 DSBL) OR VICE VERSA
1st) GET BOTH ACTIVE CP AND CMDU ON SAME SIDE ie LD 135 SCPU
so in our eg CP1 active CMDU 1 active
2nd) PUT SWITCH INTO SPLIT MODE by(THE FOLLOWING ORDER MUST BE FOLLOWED OR ELSE!)
a) THROW NORM/MAINT SWITCH TO MAINT ON ACTIVE CP(our eg CP1)
************
b) NOW THROW NORM/MAINT SWITCH TO MAINT ON STANDBY(inactive) CP
c) NOW DISABLE THE CNIs ON THE STANDBY (inactive) CP

THE SWITCH IS NOW IN SPLIT MODE CAN BE CONFIRMED BY STAT IN LD 135