Meridian>Cisco over PRI losing CLID on transfer

[Terrytele]

An example.. An call (ext or int) is transfered from a meridian phone to a Call manager phone. The meridians number is presented during the "conference" stage but when the transfer is completed the meridian number stays.

I have tried tracing the PRI to the cisco system, where it shows as...


.11:51:22 27/05/2004
ACTIVE TN 004 30
ORIG 015 0 00 11 2 TRN
TERM 004 30 TIE RMBR 122 30
DIAL DN 7007
MAIN_PM DIAL AUX_PM OUTPULSE
TALKSLOT ORIG 27TERM 27
EES_DATA:
NONE
QUEU NONE
CALL ID 0 590


AUX NARS



---- ISDN PRA CALL (TERM) ----
CALL REF # = 980
BEARER CAP = VOICE
HLC =
CALL STATE = 1 INIT
CALLING NO = 394 NUM_PLANRIVATE TON:ABBREVIATED ESN:CDP
CALLED NO = 7007 NUM_PLANRIVATE TON:ABBREVIATED ESN:CDP



.11:51:24 27/05/2004
ACTIVE TN 004 30
ORIG 015 0 00 11 2 TRN
TERM 004 30 TIE RMBR 122 30
DIAL DN 7007
MAIN_PM DIAL AUX_PM COMPLETE
TALKSLOT ORIG 27TERM 27
EES_DATA:
NONE
QUEU NONE
CALL ID 0 590


AUX NARS



---- ISDN PRA CALL (TERM) ----
CALL REF # = 980
BEARER CAP = VOICE
HLC =
CALL STATE = 4 DELIVERY
CALLING NO = 394 NUM_PLANRIVATE TON:ABBREVIATED ESN:CDP
CALLED NO = 7007 NUM_PLANRIVATE TON:ABBREVIATED ESN:CDP



.11:51:28 27/05/2004
ACTIVE TN 004 30
ORIG 012 0 00 05 0 SCR MARP 0 326 3903
TERM 004 30 TIE RMBR 122 30
DIAL DN 7007
MAIN_PM ESTD
TALKSLOT ORIG 27TERM 27
EES_DATA:
NONE
QUEU NONE
CALL ID 0 718


---- ISDN PRA CALL (TERM) ----
CALL REF # = 980
BEARER CAP = VOICE
HLC =
CALL STATE = 10 ACTIVE
CALLING NO = NUM_PLANRIVATE TON:ABBREVIATED ESN:CDP
CALLED NO = 7007 NUM_PLANRIVATE TON:ABBREVIATED ESN:CDP


As you can see in the last section the Calling numbers disappears rather than changing to that of the originator. Any clues, pointers (or even complete solutions ;0) gratefully received

Thanks
Terry

 

[johnpoole]

if you call the transfered-to station direct, does it receive clid from the same office? if so does it receive exten no. and/or name if you transfer am internal call?

john poole
bellsouth business
columbia,sc

 

[Terrytele]

All names and number passing between the two systems are fine apart from when Transfering.

 

[johnpoole]

check your rdr data in the pbx. your switch is dropping if i read your printout correctly.. are you running qsig?

john poole
bellsouth business
columbia,sc

 

[Terrytele]

Yes, Q-Sig. Thanks for the pointer, I will check over the RDR_DATA, is there anything in particular I should be looking for??

 

[johnpoole]

i would look up the options for rdr. might not be the answer but a good place to start. the switch always does what we tell it to. sometimes i have to tell mine several times..

john poole
bellsouth business
columbia,sc