Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
MD110 from USA in Europe
- Thread starter antek
- Start date
Hi Antek
I see two problems
1 Power
In Europe (Poland too) power is 230V 50Hz and in US 115V 60Hz and AC/DC units for MD are not universal (115/230).
If You have Alex you can find more info about differences in power module for this markets.
2 Cordless
Standard for Europe is 1800 MHz and for US 1900 MHz.
This US base station and handset have not certificate for Europe.
I see two problems
1 Power
In Europe (Poland too) power is 230V 50Hz and in US 115V 60Hz and AC/DC units for MD are not universal (115/230).
If You have Alex you can find more info about differences in power module for this markets.
2 Cordless
Standard for Europe is 1800 MHz and for US 1900 MHz.
This US base station and handset have not certificate for Europe.
Hi Hirei
Good question about license.
EIC number have two parts, second part it is individual customer number and first part it is market code. For example 01-1234 it is license for standard application You know that this EIC code is stored on NIU board too. And I don’t know how works this EIC control system.
For example Application System Standard (used in Poland ) and license for example 03-1234 (I don’t know AS code for US) theoretically it can’t work because AS is for other marked as code in license file.
So after transfer MD from US to Poland, AS standard should be loaded to MD, new license is needed and new NIU board or specialist who know how change EIC number on NIU board.
It is question for local Ericsson vendor “how to buy new license without new MD”
Good question about license.
EIC number have two parts, second part it is individual customer number and first part it is market code. For example 01-1234 it is license for standard application You know that this EIC code is stored on NIU board too. And I don’t know how works this EIC control system.
For example Application System Standard (used in Poland ) and license for example 03-1234 (I don’t know AS code for US) theoretically it can’t work because AS is for other marked as code in license file.
So after transfer MD from US to Poland, AS standard should be loaded to MD, new license is needed and new NIU board or specialist who know how change EIC number on NIU board.
It is question for local Ericsson vendor “how to buy new license without new MD”
whosrdaddy
Vendor
normally this can be done without any cost, IF the pbx belongs to same customer (eic code is xx-yyyy where xx is country or AS and yyyy is customer number)
--------------------------------------
What You See Is What You Get
--------------------------------------
What You See Is What You Get
Hi again
Hi whosrdaddy I was waiting for your opinion. You are an Expert
I like Alex and I find code for the application system North America
AS Code = 30
And I find some differences between AS Standard and North America
For example
Amplification/attenuation
AS Standard
Amplification/attenuation
STANDARD law of companding A is used in this application system.
The speech signals can be amplified or attenuated when passing through the switch. The following line types exist which are equal to the value found in the TRM-parameter.
[tt]
TRM Line type
0 Analogue/digital extension lines, IP extensions, PABX operator lines
1 Reserve
2 Reserve
3 Reserve
4 Analogue external line
5 Digital external line
6 2-wire tie line
7 4-wire tie line
[/tt]
AS North America
Amplification/attenuation
USA law of companding MY is used in this application system.
The speech signals can be amplified or attenuated when passing through the switch. The following line types exist which are equal to the value found in the TRM-parameter.
[tt]
TRM Line type
0 Digital extension lines, PABX operator lines, IP extensions
1 Special setup for 203 Phones
2 Analogue on premise Ext. (ONS)
3 Analogue off premise Ext. (OPS)
4 Analogue tie Trunk (A/TT)
5 Digital tie Trunk (D/TT)
6 Analogue external Trunk line (A/CO)
7 Digital external Trunk line (D/CO)
[/tt]
The next what I find is Span Converter
Copy from Alex:
The Span Converter is a K2 board designed to provide carrier adaptation between T1 transmission (1.544 Mbit/s, PCM24) and E1 transmission (2.048 Mbit/s, PCM30, CEPT). The primary purpose of the board is to provide inter-LIM (or Group Switch) communication utilizing T1 public access network. Basic signaling transmission provided by the group switch modules is E1, providing frame and service information in channel 1 (time slot 0). In North America, however, transmission over the digital public network requires T1 transmission.
Hi whosrdaddy I was waiting for your opinion. You are an Expert
I like Alex and I find code for the application system North America
AS Code = 30
And I find some differences between AS Standard and North America
For example
Amplification/attenuation
AS Standard
Amplification/attenuation
STANDARD law of companding A is used in this application system.
The speech signals can be amplified or attenuated when passing through the switch. The following line types exist which are equal to the value found in the TRM-parameter.
[tt]
TRM Line type
0 Analogue/digital extension lines, IP extensions, PABX operator lines
1 Reserve
2 Reserve
3 Reserve
4 Analogue external line
5 Digital external line
6 2-wire tie line
7 4-wire tie line
[/tt]
AS North America
Amplification/attenuation
USA law of companding MY is used in this application system.
The speech signals can be amplified or attenuated when passing through the switch. The following line types exist which are equal to the value found in the TRM-parameter.
[tt]
TRM Line type
0 Digital extension lines, PABX operator lines, IP extensions
1 Special setup for 203 Phones
2 Analogue on premise Ext. (ONS)
3 Analogue off premise Ext. (OPS)
4 Analogue tie Trunk (A/TT)
5 Digital tie Trunk (D/TT)
6 Analogue external Trunk line (A/CO)
7 Digital external Trunk line (D/CO)
[/tt]
The next what I find is Span Converter
Copy from Alex:
The Span Converter is a K2 board designed to provide carrier adaptation between T1 transmission (1.544 Mbit/s, PCM24) and E1 transmission (2.048 Mbit/s, PCM30, CEPT). The primary purpose of the board is to provide inter-LIM (or Group Switch) communication utilizing T1 public access network. Basic signaling transmission provided by the group switch modules is E1, providing frame and service information in channel 1 (time slot 0). In North America, however, transmission over the digital public network requires T1 transmission.
whosrdaddy
Vendor
to antek :
small recap : you need new software (other AS), this means new license, new PSU hardware and maybe some new TLU hardware to make external lines work. I don't think you will gain much from moving the pbx to poland. IMHO I think it will be faster AND cheaper to install a new system in poland...
--------------------------------------
What You See Is What You Get
small recap : you need new software (other AS), this means new license, new PSU hardware and maybe some new TLU hardware to make external lines work. I don't think you will gain much from moving the pbx to poland. IMHO I think it will be faster AND cheaper to install a new system in poland...
--------------------------------------
What You See Is What You Get
whosrdaddy
Vendor
rfpui,
about the TLU hardware, I was reffering to the fact that the external line type may not be the same (like analog versus ISDN).
cheers
--------------------------------------
What You See Is What You Get
about the TLU hardware, I was reffering to the fact that the external line type may not be the same (like analog versus ISDN).
cheers
--------------------------------------
What You See Is What You Get
- Status
