Maint Indication on DCH

[Telecomlady]

DCH: 17 MAINT INDICATION TIME: 9:55:24
COUNTER VALUE
2 3
10 255
11 11
18 12
25 2


DCH: 17 EST REMOTE TIME: 17:30:06 2/04/2007

TIM873 17:30 2/4/2007 CPU 1

PRI241 DCH: 17 DATA: 00000090

So I printed and it has no alarms?

PRI* TRK LOOP 17 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : NO ALARM
CH 01 - IDLE DID VOD * CH 02 - IDLE DID VOD *
CH 03 - IDLE DID VOD * CH 04 - IDLE DID VOD *
CH 05 - IDLE DID VOD * CH 06 - IDLE DID VOD *
CH 07 - IDLE DID VOD * CH 08 - IDLE DID VOD *
CH 09 - IDLE DID VOD * CH 10 - IDLE DID VOD *
CH 11 - IDLE DID VOD * CH 12 - IDLE DID VOD *
CH 13 - IDLE DID VOD * CH 14 - IDLE DID VOD *
CH 15 - IDLE DID VOD * CH 16 - IDLE DID VOD *
CH 17 - IDLE DID VOD * CH 18 - IDLE DID VOD *
CH 19 - IDLE DID VOD * CH 20 - IDLE DID VOD *
CH 21 - IDLE DID VOD * CH 22 - IDLE DID VOD *
CH 23 - IDLE DID VOD * CH 24 - IDLE DID VOD *

 

[EddieDuece]

Err PRI 241;
PRI0241
Protocol Error: No response from far end to this PRI call. Output data:
DCH: x DATA: y . Where: x = D-channel number and y = B-channel number.
Action: Report problem if condition persists.
Severity: Critical

 

[EddieDuece]

In LD 60, do a LCNT 17. (List the T1 counters for loop 17).
Then do a RCNT 17 to reset the counters.

 

[acewarlock]

I usually make my DID 3VC instaed of VOD



CH 01 - IDLE DID VOD * CH 02 - IDLE DID VOD *
CH 03 - IDLE DID VOD * CH 04 - IDLE DID VOD *
CH 05 - IDLE DID VOD * CH 06 - IDLE DID VOD *
CH 07 - IDLE DID VOD * CH 08 - IDLE DID VOD *
CH 09 - IDLE DID VOD * CH 10 - IDLE DID VOD *
CH 11 - IDLE DID VOD * CH 12 - IDLE DID VOD *
CH 13 - IDLE DID VOD * CH 14 - IDLE DID VOD *
CH 15 - IDLE DID VOD * CH 16 - IDLE DID VOD *
CH 17 - IDLE DID VOD * CH 18 - IDLE DID VOD *
CH 19 - IDLE DID VOD * CH 20 - IDLE DID VOD *
CH 21 - IDLE DID VOD * CH 22 - IDLE DID VOD *
CH 23 - IDLE DID VOD * CH 24 - IDLE DID VOD *


Thank Telecomlady
for this valuable post!

 

[jamie2]

Is this a point to point to another switch? If yes, I would recommend looking at the other end to see if you have any channels in lock out.

If this was a one time error, I would worry about it to much. However, keep an eye on the circuit.

 

[jjinkins]

It looks like you are confusing DCH 17 with Loop 17. Loop 17 does not appear to be a PRI.