LTCR Fail in Unify Openscape 4000 V8 1

[nelbd]

Hi,
I'm trying to install Unify Openscape 4000 V8, but its LTUCR (previous Version LTUCA) board not getting power. there are 2 LED (Red & Green) on the board and both status are off. Please see the attached picture.

If anyone have idea, please help me to solved the issue.

Thanks

 

[sbcsu]

CHANGE-LDAT:LROUTE=1,LSVC=VCE,LRTEL=1,TGRP=1,ODR=2,LAUTH=2,CARRIER=1,ZONE=EMPTY,VCCYC=4;

 

[nelbd]

Hi;

I change as per you suggest but till call not passing: here is the details of trunk related configuration please check and help me to solved the issue.

<DISPLAY-BUEND:TGRP=1,FORMAT=L;
DISPLAY-BUEND:TGRP=1,FORMAT=L;
H500: AMO BUEND STARTED

+------------------------------- FORMAT = L -----------------------------------+
| TGRP NUMBER : 1 TGRP NAME : BOF IN & OUT MAXIMUM NO. : 15 |
| CHARCON : NEUTRAL |
| SUBGROUP NO.: 1 DEVICE TYPE : TMANIMSG TRACENO : 0 |
| SEARCH MODE : CIRCULAR ACD THRESHOLD : * |
| NUMBER OF ASSOCIATED ROUTES : 1 PRIORITY : 1 |
| TDDRFLAG : ON TDDRTHRESHOLD: 0 SOURCEGROUPIDX : 1 |
| GDTRRULE : 0 ACDPMGRP : 0 |
| THE FOLLOWING TRUNKS (LTG-LTU-SLOT-CCT) HAVE BEEN ALLOCATED: |
+------------------------------------------------------------------------------+
| 1- 1- 8-0 | | | | |
+------------------------------------------------------------------------------+

AMO-BUEND-111 TRUNK GROUP
DISPLAY COMPLETED;
<DISPLAY-TACSUEN1=1-1-8-0;
DISPLAY-TACSUEN1=1-1-8-0;
H500: AMO TACSU STARTED
ANALOG TRUNKS (FORMAT=L)
PEN | 1-1-8-0 | |
--------|--------------------------------|--------------------------------|
DEVTYPE | TC | |
DEV | TMANIMSG | |
COTNO | 35 | |
COPNO | 35 | |
DPLN | 0 | |
ITR | 0 | |
TGRP | 1 | |
COFIDX | 0 | |
CCT | | |
DESTNO | 0 | |
INS | Y | |
COS | 22 | |
LCOSV | 1 | |
LCOSD | 1 | |
INIGHT | | |
NNO | | |
ALARMNO | 2 | |
CARRIER | 1 | |
ZONE | EMPTY | |
HMUSIC | 0 | |
LIN | 0 | |
CIDDGTS | NONE | |
CBMATTR | NONE | |
SRCGRP | 0 | |
CLASSMRK| EC G711 G729AOPT | |
TCCID | | |
DITIDX | 0 | |
TRTBL | GDTR | |
RULEIDX | 0 | |
ATNTYP | | |
MFCVAR | 0 | |
DGTPR | 5036 | |
SUPPRESS| 0 | |
DGTCNT | 0 | |
TESTNO | 1 | |
CIRCIDX | 0 | |
CRDINT | 1 | |
CCTINFO | 0 | |
DIALTYPE| MOSIG-DTMF | |
DIALVAR | 0-0 | |
COEX | 0 | |
SVCDOM | | |
---------------------------------------------------------------------------


AMO-TACSU-111 CONFIGURATION OF ANALOG TRUNK CIRCUITS IN THE SWU
DISPLAY COMPLETED;
<DISPLAY-COT:COTNO=35;
DISPLAY-COT:COTNO=35;
H500: AMO COT STARTED

COT: 35 INFO: TMANI
DEVICE: INDEP SOURCE: DB
PARAMETER:
PRIORITY FOR AC WILL BE DETERMINED FROM MESSAGE PRI
RECALL IF USER HANGS UP IN CONSULTATION CALL RCL
TRUNK CALL TRANSFER XFER
TRUNK SIGNALING ANSWER ANS
KNOCKING OVERRIDE POSSIBLE KNOR
CALL EXTEND FOR BUSY, RING OR CALL STATE CEBC
NETWORKWIDE AUTOMATIC CALLBACK ON BUSY CBBN
NETWORKWIDE AUTOMATIC CALLBACK ON FREE CBFN
MALICIOUS CALL TRACE, E.G. FOR ISDN TRAI
END-OF-DIAL FOR BLOCK IS SET BLOC
ACTIVATE TRANSIT COUNTER ADMINISTRATION FOR S0/S2 LINE ATRS
TSC-SIGNALING FOR NETWORKWIDE FEATURES (MANDATORY) TSCS
NO SIMPLE DIALOG AVAILABLE NOSD
DON'T SEND CINT LEG2,IF CENTR. ATND IN HETERO. NETWORK NIN2
NPI ISDN, OUTGOING CALL NPIS
NO TONE NTON

AMO-COT -111 CLASS OF TRUNK FOR CALL PROCESSING
DISPLAY COMPLETED;
<DISPLAY-COP:COPNO=35;
DISPLAY-COP:COPNO=35;
H500: AMO COP STARTED

COP: 35 INFO: TMANI
DEVICE: INDEP SOURCE: DB
PARAMETER:
DUALTONE MULTIPLEFREQUENCY DTMF
LINE WITH ANSWERING ANS
SPECIAL MODE SFRM
BACKWARD RELEASE AFTER RELEASE RLSA
MAKE/BREAK RATIO (60/40) BR64
TIME DEPENDENT EXCHANGE DIALTONE TDED
NO ANSWER ON RECEIPT OF FIRST CHARGE PULSE NOAN
NOT 1A, I.E OUTGOING DIGITS NOT WITHHELD NO1A
DIRECT INWARD TRUNK, NO AC INTERCEPT DITW
START-DIALING-SIGNAL TIMER 1 (AMO DTIM2: PARAMETER STADIAL1) TIM1
LINE WITH NO START-DIAL-SIGNAL NSDL
INTERDIGIT PAUSE 2 (AMO DTIM2: IDGT2) IDP2
MAKE/BREAK RATIO FOR DTMF 1 (PULSE=80MS,PAUSE=80MS) DTM1

CO TRUNK ACCESS:
TRUNK ACCESS TA

TOLL ACCESS:
TRUNK ACCESS TA

AMO-COP -111 CLASS OF PARAMETER FOR DEVICE HANDLER
DISPLAY COMPLETED;
<DISPLAY-COSSU:TYPE=COS,COS=22;
DISPLAY-COSSU:TYPE=COS,COS=22;
H500: AMO COSSU STARTED
+------+-----------------+---------------+-----------------+
| COS | VOICE | FAX | DTE |
+------+-----------------+---------------+-----------------+
| 22 |> |
| | TA | NOCO | NOCO |
| | REVCHA | NOTIE | NOTIE |
| | TNOTCR | | |
| | CDRS | | |
| | CDRSTN | | |
| | CDRC | | |
| | CDRIND | | |
| | CDRINT | | |
| | COSXCD | | |
| | MB | | |
| | TRACE | | |
| | CFNR | | |
| | FWDNWK | | |
| | CFB | | |
| | FWDECA | | |
| | FWDEXT | | |
| | CTLS | | |
+------+-----------------+---------------+-----------------+

AMO-COSSU-111 CLASSES OF SERVICE
DISPLAY COMPLETED;
<DISPLAY-COSSU:TYPE=LCOSV;
DISPLAY-COSSU:TYPE=LCOSV;
H500: AMO COSSU STARTED
+----+----------------------------------------------------------------+-----+
|LCOS| LAUTH |COPIN|
| V | 1 2 3 4 5 6 | |
| |1234567890123456789012345678901234567890123456789012345678901234| |
| |>SERVICE INFORMATION | |
+----+----+----|----+----|----+----|----+----|----+----|----+----|----+-----+
| 1|X...............................................................| 0 |
| |>TIE ACCESS | |
| 2|XX..............................................................| 0 |
| |>LOCAL ACCESS | |
| 3|XXX.............................................................| 0 |
| |>LOCAL+MOBILE ACCESS | |
| 4|XXXX............................................................| 0 |
| |>NWD ACCESS | |
| 5|XXXXX...........................................................| 0 |
| |>ISD ACCESS | |
| 6|................................................................| 0 |
| 7|................................................................| 0 |
| 8|................................................................| 0 |
| 9|................................................................| 0 |
| 10|XXXXXXXXXX......................................................| 0 |
| |>OPERATOR | |
| 11|XXXXX....XX.....................................................| 0 |
| |>CEO DIRECT T&T IN | |
| 12|XXXXX....X.X....................................................| 0 |
| |>DMS DIRECT T&T IN | |
| 13|XXXXX.......X...................................................| 0 |
| |>MD DIRECT T&T IN | |
| 14|................................................................| 0 |
| 15|................................................................| 0 |
| 16|XXXXXXXXXX.....X................................................| 0 |
| |>OPERATOR+ MOBILE | |
| 17|................................................................| 0 |
| 18|................................................................| 0 |
| 19|................................................................| 0 |
| 20|................................................................| 0 |
| 21|................................................................| 0 |
| 22|................................................................| 0 |
| 23|................................................................| 0 |
| 24|................................................................| 0 |
| 25|................................................................| 0 |
| 26|................................................................| 0 |
| 27|................................................................| 0 |
| 28|................................................................| 0 |
| 29|................................................................| 0 |
| 30|................................................................| 0 |
| 31|................................................................| 0 |
| |>INTERNAL ONLY | |
| 32|XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX................................| 0 |
| |>FULL ACCESS | |
+----+----------------------------------------------------------------+-----+

AMO-COSSU-111 CLASSES OF SERVICE
DISPLAY COMPLETED;
<DISPLAY-RICHT:MODE=LRTE;
DISPLAY-RICHT:MODE=LRTE;
H500: AMO RICHT STARTED
+-----------------------------------------------------------------+
| LRTE = 1 NAME = BOF IN/OUT LINE (NEUTRAL) LSVC = VCE |
| DNNO =1 -1 -100 PDNNO = 0 |
| ROUTOPT = NO REROUT = NO PLB = YES FWDBL = NO |
| DTMFCNV = FIX DTMFDSP = DIGITS DTMFTEXT = TONE DIALLING |
| DTMFPULS = PP300 BUGS = LIN ROUTATT = NO MAINGRP = 2 |
| EMCYRTT = NO CONFTONE = NO RERINGRP = NO RTENO = 2 |
| INFO = NEUTRAL |
| NOPRCFWD = NO |
| NITO = NO |
| CLNAMEDL = NO |
| FWDSWTCH = NO |
| LINFEMER = NO |
| NOINTRTE = NO |
+-----------------------------------------------------------------+
| TGRP = 1 LDAT BOF IN & OUT (NEUTRAL) SUBGROUP = 1 |
+-----------------------------------------------------------------+
H23: SVC FAX IS NOT USED FOR RICHT BRANCH CD. VOICE IS USED
FOR G3 FAX AND DATA FOR G4 FAX.

AMO-RICHT-111 TRUNK ROUTING
DISPLAY COMPLETED;
<DISPLAY-LDAT:;
DISPLAY-LDAT:;
H500: AMO LDAT STARTED
+------------------------------------------------------------------------------+
| LROUTE = 1 LDPLN NAME = BOF IN/OUT LINE SERVICE = VCE |
| TYPE = LCR DNNO OF ROUTE = 1 -1 -100 |
| SERVICE INFO = |
+------+-----+-----+----+-----+----------+-----------+----------+------+-------+
| | | | | | SCHEDULE | CARRIER | | | |
|LRTEL | LVAL|TGRP | ODR|LAUTH| ABCDEFGH | ZONE| LATTR | LDSRT|COTIDX |
+------+-----+-----+----+-----+----------+-----------+----------+------+-------+
| 1| 1| 1| 2| 2 | ******** | 1 EMPTY| WCHREG | | 0 |
+------------------------------------------------------------------------------+

AMO-LDAT -111 LCR-DIRECTIONS
DISPLAY COMPLETED;

<DISPLAY-LODR:ODR=2;
DISPLAY-LODR:ODR=2;
H500: AMO LODR STARTED
+-------------------------------------------------------+
| ODR POSITION CMD PARAMETER |
+--------+----------------------------------------------+
| 2 | 1 ECHO 2 |
| | 2 END |
+--------+----------------------------------------------+
H03: THE NEXT FREE ODR IS 1

AMO-LODR -111 ADMINISTRATION OF LCR OUTDIAL RULES
DISPLAY COMPLETED;

DISPLAY-LDPLN:TYPE=LDP;
H500: AMO LDPLN STARTED
+--------------+-------------------------------------------------+
| | |
| DIPLNUM: 0| |
| LDPNO :3 | LDP : 81-X |
| | SPC : 22 |
| | FDSFIELD : 0 SDSFIELD : 0 PINDP : N |
+------+-------+-------------------------------------------------+
| DPLN | LROUTE| LAUTH |
|------+-------+-------------------------------------------------+
| 0 | 1 | 2 |
| 1 | 1 | 2 |
| 2 | 1 | 2 |
| 3 | 1 | 2 |
| 4 | 1 | 2 |
| 5 | 1 | 2 |
| 6 | 1 | 2 |
| 7 | 1 | 2 |
| 8 | 1 | 2 |
| 9 | 1 | 2 |
| 10 | 1 | 2 |
| 11 | 1 | 2 |
| 12 | 1 | 2 |
| 13 | 1 | 2 |
| 14 | 1 | 2 |
| 15 | 1 | 2 |
+--------------+-------------------------------------------------+
| | |
| DIPLNUM: 0| |
| LDPNO :1 | LDP : 9-Z |
| | SPC : 22 |
| | FDSFIELD : 0 SDSFIELD : 0 PINDP : N |
+------+-------+-------------------------------------------------+
| DPLN | LROUTE| LAUTH |
|------+-------+-------------------------------------------------+
| 0 | 1 | 2 |
| 1 | 1 | 2 |
| 2 | 1 | 2 |
| 3 | 1 | 2 |
| 4 | 1 | 2 |
| 5 | 1 | 2 |
| 6 | 1 | 2 |
| 7 | 1 | 2 |
| 8 | 1 | 2 |
| 9 | 1 | 2 |
| 10 | 1 | 2 |
| 11 | 1 | 2 |
| 12 | 1 | 2 |
| 13 | 1 | 2 |
| 14 | 1 | 2 |
| 15 | 1 | 2 |
+------+-------+-------------------------------------------------+

AMO-LDPLN-111 ADMINISTRATION LCR DIALPLAN
DISPLAY COMPLETED;

 

[sbcsu]

OK so you have 1 analog trunk connected to the system ?
The COT/COP are incorrect but you should still be able to pick up the trunk.

Do you have a test phone ? - one that you can connect in parallel across the trunk and listen to see if the trunk is being picked up when you dial 9 on the system.

Do you have any other systems configured like this ?
It seems to be a lot of work just to get one analog line working - will you be connecting up SIP or ISDN to this system ?

 

[nelbd]

Hi thanks for your support. Yes now I can access and make outgoing PSTN calls. Actually the PSTN line I was connected that one have no outgoing facility. So I change the PSTN line and calls are passing now. But after completing dial getting delay(near about 30_35 second) ringback tone.
Can you please tell me what is wrong in COT / COP?
Yes I was worked in Siemens Bangladesh till 2012 and have experience for commissioning Hipath 4000 V 2.0.
Yes will connect SIP trunk and HFA phone user.
I added STMIX board as per your sample data but can't change CGWB (WBMDATA)
Like CHANGE-CGWB:CGW,3,1,WBMDATA,"HP4K-DEVEL",,ENGR;
Can you tell me what will be pass format here?

Regards

 

[sbcsu]

Most of the CGWB is standard, only change the IP addressing marked as x.x.x.x

The COT/COP seem to be for ISDN

The reason for the delay in outgoing would be that you have 9-Z
Which means that you are dialling 9 for a line then the Z means take everything dialled and wait for a timeout.

As a test dial the number and put a # at the end - it should progress quicker.

What you can do is 'flesh out' the LDPLN to make more sense for your territory, for example

9-1800-xxxxxx would mean that if you dial 9 for a line then 1800 after that you would dial 6 digits, then you would connect.
(However your ODR - out dial rule - would have to change)

Examples COT/COP for analog trunks: (DIT - Direct Inward Trunk - rings to a specific extension - set in TACSU DGTPR)
ADD-COP:1,DTMF&RLSB&RLSA&SPTR&NTON&DTM1,TA,TA;
CHANGE-COP:1,COPADD,,,,ANMOSIG,"COP FOR NON DIT ANALOGUE TRUNKS";
ADD-COP:2,DTMF&RLSB&RLSA&DITW&SPTR&NTON&DTM1,TA,TA;
CHANGE-COP:2,COPADD,,,,ANMOSIG,"COP FOR DIT ANALOGUE TRUNKS";

ADD-COT:1,RCL&XFER&CHRT&CEOC&CEBC&CPS6&RCLS&BSHT&CECO&ICZL&ICZO&CCTN&CTLS&NTON;
CHANGE-COT:1,COTADD,,ANMOSIG,"COT FOR NON DIT ANALOGUE TRUNKS";
ADD-COT:2,RCL&XFER&CHRT&CEOC&CEBC&CPS6&RCLS&BSHT&CECO&ICZL&ICZO&CCTN&CTLS&NTON;
CHANGE-COT:2,COTADD,,ANMOSIG,"COT FOR DIT ANALOGUE TRUNKS";

 

[nelbd]

Hi Dear,
Thanks for your solutions. delay issue are solved.
I tried to ADD CGWB as per your sample data
ADD-CGWB:3,1,NORMAL,192.168.100.15,255.255.255;

But when I tried to change CGWB WBMDATA its ask password like
CHANGE-CGWB:CGW,3,1,WBMDATA,"HP4K-DEVEL",,ENGR;
H500: AMO CGWB STARTED
F11: NEW USER NAME.PARAMETER PASSWWBM MUST BE ENTERED. 3-1

AMO-CGWB -111 CONFIGURATION OF HG3500 BOARD
CHANGE NOT COMPLETED;

I tried several digit like 123456 or 112244 but getting feedback illegal value. can you suggest me what should i put in PASSWWBM field?

 

[Moriendi]

You don't need to put anything in there. Assistant will change the passwords any for access via GUI. Leave it blank.

 

[nelbd]

Hi Dear,

I tried to check the STMIX via 4000 Assistant V8 and get the result below:

Please suggest me what should i don now.

Thanks and regards

 

[sbcsu]

Work through the following - the default gateway, processor (SIPCO A & SIPCO B if applicable) have to be added
CHANGE-CGWB:CGW,3,1,GLOBIF,,,213,NO,0,x.x.x.x,4060,AUTONEG,0,0,10,0,4061,x.x.x.x,x.x.x.x,NO,0.0.0.0,5060,5061;

 

[sbcsu]

Or just REG-CGWB; and paste here

 

[nelbd]

Hi,
here is the details
REG-CGWB;
H500: AMO CGWB STARTED
ADD-CGWB:3,1,NORMAL,192.168.100.15,255.255.255.0;
CHANGE-CGWB:CGW,3,1,GLOBIF,,,213,NO,0,192.168.100.1,4060,AUTONEG,0,0,10,0,4061,192.168.0.5,192.168.0.6,NO,0.0.0.0,5060,5061;
CHANGE-CGWB:CGW,3,1,SERVIF,"TRM","HICOM";
CHANGE-CGWB:CGW,3,1,ASC,29100,30099,184,104,YES,YES,YES,YES,PRIO1,G711A,NO,30;
CHANGE-CGWB:CGW,3,1,ASC,,,,,,,,,PRIO2,G729A,NO,20;
CHANGE-CGWB:CGW,3,1,ASC,,,,,,,,,PRIO3,NONE,NO,30;
CHANGE-CGWB:CGW,3,1,ASC,,,,,,,,,PRIO4,NONE,NO,20;
CHANGE-CGWB:CGW,3,1,ASC,,,,,,,,,PRIO5,NONE,NO,20;
CHANGE-CGWB:CGW,3,1,ASC,,,,,,,,,PRIO6,NONE,NO,20;
CHANGE-CGWB:CGW,3,1,ASC,,,,,,,,,PRIO7,NONE,NO,20;
CHANGE-CGWB:CGW,3,1,ASC,,,,,,,,,PRIO8,NONE,NO,20;
CHANGE-CGWB:CGW,3,1,ASC,,,,,,,,,PRIO9,NONE,NO,20;
CHANGE-CGWB:CGW,3,1,GKDATA,,1719,"PRIMARYRASMANAGERID",,,1719,"SECONDARYRASMANAGERID",,120;
CHANGE-CGWB:CGW,3,1,MGNTDATA,192.168.100.5,8000,192.168.100.6,443,CLASSIC;
CHANGE-CGWB:CGW,3,1,DMCDATA,8,YES,NO;
CHANGE-CGWB:CGW,3,1,WBMDATA,"HP4K-DEVEL",,ENGR;
CHANGE-CGWB:CGW,3,1,WBMDATA,"HP4K-SU",,SU;
CHANGE-CGWB:CGW,3,1,WBMDATA,"HP4K-ADMIN",,ADMIN;
CHANGE-CGWB:CGW,3,1,WBMDATA,"HP4K-READER",,READONLY;
CHANGE-CGWB:CGW,3,1,GWDATA,"PRIMARYRASMANAGERID",;
CHANGE-CGWB:CGW,3,1,H235DATA,NO,NO,"h235securedgateway",,100,242-191-30-119-188-83-173-161-43-0-70-36-218-74-169-221-78-102-174-170;
CHANGE-CGWB:CGW,3,1,SIPTRERH,NO,,,;
CHANGE-CGWB:CGW,3,1,SIPTRSSA,NO,0.0.0.0,5060,5061,300,0.0.0.0,5060,5061;
CHANGE-CGWB:CGW,3,1,DLSDATA,,10444,NO;
CHANGE-CGWB:CGW,3,1,JB,40,120,20,4,60,200,2;
CHANGE-CGWB:CGW,3,1,MANLANIF,0.0.0.0,0.0.0.0,NO,0,0.0.0.0;

AMO-CGWB -111 CONFIGURATION OF HG3500 BOARD
REGENERATE COMPLETED;
<

Regards

 

[sbcsu]

You do need to plug in a CAT6 cable to the front of the board (STMIX) to your IP Router - OK?

 

[nelbd]

Yes it's connected to lan1 and get ping from laptop.

 

[nelbd]

Hi,
Now 4000 Assistant can login. Thanks a lot for your support. can you please tell me what is the ip address should i put for:
CHANGE-CGWB:CGW,3,1,MANLANIF,0.0.0.0,0.0.0.0,NO,0,0.0.0.0;

Regards

 

[sbcsu]

That's for a Management LAN - I have not used it.

Ensure the STMIX has latest loadware via Assistant

 

[nelbd]

Yes I Updated it from RMX

am troubling you lots. Actually I worked till Hipath 4000 V.2 and this one is totally new for me. What ever I added HFA User (SBCSU) and SIP trunk (TDCSU) but can't configure Openscape 60 HFA phone set. there is a manual inside the box but nothing is there.

Can you please help me or give me any configuration note.

Thanks a lot

 

[sbcsu]

It's just a HFA phone - configure it the same as HFA User SBCSU ?

 

[donb01]

I'm just throwing it out there, but I can see a number of cards on the far right side of the cabinet in the first photo because the lights are shing thru the slot covers. I don't know what is all in there, but I do note there is only one power supply in that cabinet. I don't know what the threshold of "stuff" is before you need to add an additional power supply, or if that is only for redundancy. All my cabinets have 2, and a couple of them have 3.... Don't know if that is related to anything here or not, but could be something to consider down the road?


Don Bruechert, Voice Comm Analyst II
CareTech Solutions @ Holy Family Memorial
Manitowoc, WI, USA

 

[nelbd]

Hi,
Its just Openscape 60 HFA Phone.

I added user like:

DISPLAY-SBCSU:STNO=4588;
H500: AMO SBCSU STARTED

----------------------------- USER DATA ----------------------------------------
STNO =4588 OPT =OPTI COS1 =10 DPLN =0
MAINO =4588 CONN =IP2 COS2 =10 ITR =0
PEN =1- 3- 1- 2 LCOSV1 =32 COSX =0
INS =Y ASYNCT =500 LCOSV2 =32
SSTNO =N PERMACT = LCOSD1 =1 CBKBMAX =5
TRACE =N EXTBUS = LCOSD2 =1 RCBKB =N
ALARMNO =0 DFSVCANA= SPDI =0 RCBKNA =N
HMUSIC =0 FLASH = SPDC1 = CBKNAMB =Y
PMIDX =0 SPDC2 =
SECR =N DIGNODIS=N DSSTNA =N COMGRP =0
STD =0 CALLOG =NONE DSSTNB =Y TEXTSEL =ENGLISH

REP =0 OPTICOM =N OPTIUSB : VPI =
IDCR =N OPTICA = OPTIS0A :0 VCI =
APPM = OPTIDA = OPTISPA :0 PATTERN =
BLF =N OPTIUP0E:0 OPTIABA :0

DCFWBUSY=N HEADSET =N APMOBUSR=N APICLASS=TSX
DNIDSP =N HSKEY =NORMAL IPCODEC =G711P SECAPPL =0
DTMFBLK =N IPPASSW =
DTMFCTRD=N BASICSVC=
DVCFIG =OPTIIP TSI =1 SPROT = SOPTIDX =
API 2 DPROT = DOPTIDX =
FPROT = FOPTIDX =
----------------------------------UFIP----------------------------------------

USER ID =
SECZONE =
SUBIPADD =000.000.000.000

------------------- MOBILE HFA STATE -----------------------------------------
IP PHONE INACTIVE :N
------------------- ACTIVATION IDENTIFIERS FOR FEATURES ----------------------
HTOS :N DND :N
HTOD :N VCP :Y TWLOGIN :N
HTOF :N CWT :N
------------------- FEATURES AND GROUP MEMBERSHIPS ---------------------------
PUGR : ESSTN :
KEYSYS :N NOPTNO :
SRCGRP 1 ) TCLASS : 0
HUNT CD :N
------------------- SUBSCRIBER ATTRIBUTES (AMO SDAT) -------------------------
NONE
------------------------------------------------------------------------------

AMO-SBCSU-111 STATION AND S0-BUS CONFIGURATION OF SWITCHING UNIT
DISPLAY COMPLETED;

and configure the Openscape 60 HFA phone set like:

Network Configuration:
IP: 192.168.100.99
SUB: 255.255.255.0
GW: 192.168.100.1
DNS:8.8.8.8

System Configuration:
GW:192.168.100.15 (STMIX IP)
Subscriber: 4588

But the phone set didn't synchronize with the system
The Openscape 60 HFA phone showing : Telephony down (LI1,H02)

 

[nelbd]

Dear Donb01,
Slot 2-6 are empty. Others LTU have 2 power supply. See the picture the same send by Unify Germany.

Thanks