Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

LTCR Fail in Unify Openscape 4000 V8 1

Status
Not open for further replies.

nelbd

Vendor
Dec 25, 2019
30
BD
Hi,
I'm trying to install Unify Openscape 4000 V8, but its LTUCR (previous Version LTUCA) board not getting power. there are 2 LED (Red & Green) on the board and both status are off. Please see the attached picture.
System_Status_pnp8pc.jpg
LTUCR_Status_1_vfgqkp.jpg
LTUCR_Status_2_iysx6m.jpg


If anyone have idea, please help me to solved the issue.

Thanks
 
Dear SBCSU,
Thanks for your replay. Already I did it but no change. Can you tell me what is the COMWIN or SuSE Linux command for activate/enable RTM in Unify Openscape 4000 V8 Eco Server?

Thanks once again.
 
Well you do need the cables plugged in as well - in your photo there are no cables plugged in.

Get one CAT6 or better cable from each processor and plug into Front of LTUCR
 
Dear SBCSU,
Thanks for your suggestion. The picture here I shared it's upper shelf picture which cable I removed and pull the card to check. There are 2 more shelf I mean total 3 LTU. Others are till connected but all LTUCR status are same.

I'm new in version 7&8 architecture. Hope I can make you understand the issue.

Thanks.
 
Dear SBCSU,
Yes you're absolutely correct. Version 8 Release 22 and duplex.
Thanks.
 
Connect the processor to processor cable at the back between the 2 processors
Also connect up the Atlantic LAN to Atlantic LAN Patch Lead and the Corosync to Corosync Patch Lead at the back between the 2 processors.
 
Please post a photo of the back of the 2 x Processors and how they are interconnected -
 
Dear SBCSU,
Thanks for your support,
After activate RTM by AMO USSU the problem is solved.

I have another question.
Can I use STMIX S30810-Q2343-X single board for IP trunk and IP phone Or need 2 individual board for IP trunking and IP phone?

Thanks once again.
 
ACT-USSU:RTM
OK

I would setup the STMIX for HFA/IP Trunk and SIP extensions

Example:

ADD-BFDAT:21,HG3550&HG3530&SIP,BCHL60&BCHL120,;
CHA-BFDAT:CONT,21,HG3550,1,1,;
CHA-BFDAT:CONT,21,HG3530,120,,40;
CHA-BFDAT:CONT,21,SIP,10,,5;

ADD-BCSU:IPGW,1,21,1,"Q2343-X ",1,0,21,,30,5,10,,,0,IPV4,NO,NO;

ADD-CGWB:21,1,NORMAL,x.x.x.x,x.x.x.x;
CHANGE-CGWB:CGW,21,1,GLOBIF,,,213,NO,0,x.x.x.x,4060,AUTONEG,0,0,10,0,4061,x.x.x.x,x.x.x.x,NO,0.0.0.0,5060,5061;
CHANGE-CGWB:CGW,21,1,SERVIF,"TRM","HICOM";
CHANGE-CGWB:CGW,21,1,ASC,29100,30099,184,104,YES,YES,YES,YES,PRIO1,G711A,NO,30;
CHANGE-CGWB:CGW,21,1,ASC,,,,,,,,,PRIO2,G729A,NO,20;
CHANGE-CGWB:CGW,21,1,ASC,,,,,,,,,PRIO3,NONE,NO,30;
CHANGE-CGWB:CGW,21,1,ASC,,,,,,,,,PRIO4,NONE,NO,20;
CHANGE-CGWB:CGW,21,1,ASC,,,,,,,,,PRIO5,NONE,NO,20;
CHANGE-CGWB:CGW,21,1,ASC,,,,,,,,,PRIO6,NONE,NO,20;
CHANGE-CGWB:CGW,21,1,ASC,,,,,,,,,PRIO7,NONE,NO,20;
CHANGE-CGWB:CGW,21,1,ASC,,,,,,,,,PRIO8,NONE,NO,20;
CHANGE-CGWB:CGW,21,1,ASC,,,,,,,,,PRIO9,NONE,NO,20;
CHANGE-CGWB:CGW,21,1,GKDATA,,1719,"PRIMARYRASMANAGERID",,,1719,"SECONDARYRASMANAGERID",,120;
CHANGE-CGWB:CGW,21,1,MGNTDATA,x.x.x.x,8000,x.x.x.x,443,CLASSIC;
CHANGE-CGWB:CGW,21,1,DMCDATA,10,YES,NO;
CHANGE-CGWB:CGW,21,1,WBMDATA,"HP4K-DEVEL",,ENGR;
CHANGE-CGWB:CGW,21,1,WBMDATA,"HP4K-SU",,SU;
CHANGE-CGWB:CGW,21,1,WBMDATA,"HP4K-ADMIN",,ADMIN;
CHANGE-CGWB:CGW,21,1,WBMDATA,"HP4K-READER",,READONLY;
CHANGE-CGWB:CGW,21,1,GWDATA,"PRIMARYRASMANAGERID",;
CHANGE-CGWB:CGW,21,1,H235DATA,NO,NO,"h235securedgateway",,100,242-191-30-119-188-83-173-161-43-0-70-36-218-74-169-221-78-102-174-170;
CHANGE-CGWB:CGW,21,1,LEGKDATA,1,898100,NO;
CHANGE-CGWB:CGW,21,1,SIPTRERH,NO,,,;
CHANGE-CGWB:CGW,21,1,SIPTRSSA,NO,0.0.0.0,5060,5061,300,0.0.0.0,5060,5061;
CHANGE-CGWB:CGW,21,1,DLSDATA,x.x.x.x,18443,NO;
CHANGE-CGWB:CGW,21,1,JB,40,120,20,4,60,200,2;
CHANGE-CGWB:CGW,21,1,MANLANIF,0.0.0.0,0.0.0.0,NO,0,0.0.0.0;


GKREG to be added for IP trunk
 
Dear SBCSU,

Thanks a lot.
Tomorrow I will go to site and try as per your sample data. please send me command details also for IP Trunk.

Regards
 
Hi SBCSU,
Thanks for your support. The STMIX board is added and become online. Now I have some more asking.
1. As I can remember there is a feature to check PSTN line tone via normal dtmf set. Actually last 6 years I was out of this Trac and forgot all. Can you please tell me the procedure to check it.
2.I configure WABE, BUEND, COT, COP, COSSU, TACSU, LODR, RICHT, LDPLN as per Hipath 4000 V4.
The problem is when am dialing any out side number not getting any ringback tone or any voice, I physically checked the PSTN line and it's ok. As I doubt the system not sending any digit to the PSTN line.
Can you please give me any sample configuration of openscape version 8 for trunking and routing? It will be great help for me.
3.Can you please give me IP Trunking and routing configuration for STMIX card.

Waiting and deeply expecting your cooperation.

Regards
 
Hi,
Please clarify.

1. Sorry, I have no idea on this.
2. When you say PSTN - that is normally an analog trunk. Is it an ISDN trunk or SIP trunk ?
 
OK then
A normal analog trunk would go to the TMANI on your system,
Use TACSU rather than TDCSU to add
 
From V8 the LTU processor come up only after LTG activation.

And also please note that while preparing XML file in configurator do not forget to check the RTM .

All are confused that the not find the power in LTU processor card .
 
Hi Dear,

I tried to make a dial plan but can't success. My problem is call not passing through PSTN line. I have 2 LDPLN (9-X and 81-Z)for same route.
when using DPLN 9-X
getting busy tone when dial any digit after 9.
when using DPLN 81-Z
getting busy tone after dial the complete number (like 8101730934209)

Here is my configuration,I would like to requested you please check the data and help me to solved the issue.

My System Is Openscape 4000 Eco Server (Duplex)V8 R2.22.0

Regards



ADD-BCSU:pER,1,1,1,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,1,2,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,1,3,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,1,4,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,1,5,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:SIUP,1,1,6,"Q2287-X ", ANIF&ANIF&ANIF&ANIF&ANIF&ANIF&ANIF&ANIF,0,5,0;
ADD-BCSU:pER,1,1,8,"Q2327-X100",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,1,9,"Q2327-X100",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,1,10,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,1,11,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,1,12,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,1,13,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,1,14,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,1,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,2,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,3,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,4,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,5,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,6,"Q2327-X100",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,8,"Q2327-X100",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,9,"Q2327-X100",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,10,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,11,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,12,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,13,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,14,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:IPGW,1,3,1,"Q2343-X ",1,0,21,,30,5,10,,,0,IPV4,NO,NO;
ADD-BCSU:pER,1,3,8,"Q2327-X100",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,3,10,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,3,11,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,3,12,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,3,13,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,3,14,"Q2227-X ",0,0,,,,,, ,0,,;

ADD-COSSU:,5,,,,,,,,"";
CHA-COSSU:COS,5,TA&REVCHA&TNOTCR&COSXCD&MB&CFNR&VCE&FWDFAS;
CHA-COSSU:COS,5,FWDDIR&FWDBAS&FWDECA&FWDEXT&CCBS&CW&CTLS;
CHA-COSSU:COS,5,,NOCO&NOTIE;
CHA-COSSU:COS,5,,,NOCO&NOTIE;
ADD-COSSU:,6,,,,,,,,"TRACE COS";
CHA-COSSU:COS,6,TA&TNOTCR&COSXCD&MB&TRACE&CCBS&CW;
CHA-COSSU:COS,6,,NOCO&NOTIE;
CHA-COSSU:COS,6,,,NOCO&NOTIE;
ADD-COSSU:,10,,,,,,,,"";
CHA-COSSU:COS,10,TA&TNOTCR&COSXCD&MB&CFNR&VCE&FWDNWK&CFB;
CHA-COSSU:COS,10,CFSWF&FWDECA&FWDEXT&GRPCAL&HGICLD;
CHA-COSSU:COS,10,,NOCO&NOTIE;
CHA-COSSU:COS,10,,,NOCO&NOTIE;
ADD-COSSU:,15,,,,,,,,"GENERAL COS";
CHA-COSSU:COS,15,TA&TNOTCR&COSXCD&MB;
CHA-COSSU:COS,15,,NOCO&NOTIE;
CHA-COSSU:COS,15,,,NOCO&NOTIE;
ADD-COSSU:,22,,,,,,,,"";
CHA-COSSU:COS,22,TA&REVCHA&TNOTCR&CDRS&CDRSTN&CDRC&CDRIND&CDRINT;
CHA-COSSU:COS,22,COSXCD&MB&TRACE&CFNR&FWDNWK&CFB&FWDECA&FWDEXT;
CHA-COSSU:COS,22,CTLS;
CHA-COSSU:COS,22,,NOCO&NOTIE;
CHA-COSSU:COS,22,,,NOCO&NOTIE;
ADD-COSSU:,32,,,,,,,,"TRUNK COS";
CHA-COSSU:COS,32,TA&REVCHA&TNOTCR&CTLS;
CHA-COSSU:COS,32,,NOCO&NOTIE;
CHA-COSSU:COS,32,,,NOCO&NOTIE;
CHA-COSSU:LCOSV,1,,2&&64;
CHA-COSSU:LCOSV,1,,,,,0;
CHA-COSSU:LCOSV,1,,,,,,"TIE ACCESS";
CHA-COSSU:LCOSV,2,1&&2;
CHA-COSSU:LCOSV,2,,,,,0;
CHA-COSSU:LCOSV,2,,,,,,"LOCAL ACCESS";
CHA-COSSU:LCOSV,3,1&&3;
CHA-COSSU:LCOSV,3,,,,,0;
CHA-COSSU:LCOSV,3,,,,,,"LOCAL+MOBILE ACCESS";
CHA-COSSU:LCOSV,4,1&&4;
CHA-COSSU:LCOSV,4,,,,,0;
CHA-COSSU:LCOSV,4,,,,,,"NWD ACCESS";
CHA-COSSU:LCOSV,5,1&&5;
CHA-COSSU:LCOSV,5,,,,,0;
CHA-COSSU:LCOSV,5,,,,,,"ISD ACCESS";
CHA-COSSU:LCOSV,6,,,,,0;
CHA-COSSU:LCOSV,7,,,,,0;
CHA-COSSU:LCOSV,8,,,,,0;
CHA-COSSU:LCOSV,9,,,,,0;
CHA-COSSU:LCOSV,10,1&&10;
CHA-COSSU:LCOSV,10,,,,,0;
CHA-COSSU:LCOSV,10,,,,,,"OPERATOR";
CHA-COSSU:LCOSV,11,1&&5&10&&11;
CHA-COSSU:LCOSV,11,,,,,0;
CHA-COSSU:LCOSV,11,,,,,,"CEO DIRECT T&T IN";
CHA-COSSU:LCOSV,12,1&&5&10&12;
CHA-COSSU:LCOSV,12,,,,,0;
CHA-COSSU:LCOSV,12,,,,,,"DMS DIRECT T&T IN";
CHA-COSSU:LCOSV,13,1&&5&13;
CHA-COSSU:LCOSV,13,,,,,0;
CHA-COSSU:LCOSV,13,,,,,,"MD DIRECT T&T IN";
CHA-COSSU:LCOSV,14,,,,,0;
CHA-COSSU:LCOSV,15,,,,,0;
CHA-COSSU:LCOSV,16,1&&10&16;
CHA-COSSU:LCOSV,16,,,,,0;
CHA-COSSU:LCOSV,16,,,,,,"OPERATOR+ MOBILE";
CHA-COSSU:LCOSV,17,,,,,0;
CHA-COSSU:LCOSV,18,,,,,0;
CHA-COSSU:LCOSV,19,,,,,0;
CHA-COSSU:LCOSV,20,,,,,0;
CHA-COSSU:LCOSV,21,,,,,0;
CHA-COSSU:LCOSV,22,,,,,0;
CHA-COSSU:LCOSV,23,,,,,0;
CHA-COSSU:LCOSV,24,,,,,0;
CHA-COSSU:LCOSV,25,,,,,0;
CHA-COSSU:LCOSV,26,,,,,0;
CHA-COSSU:LCOSV,27,,,,,0;
CHA-COSSU:LCOSV,28,,,,,0;
CHA-COSSU:LCOSV,29,,,,,0;
CHA-COSSU:LCOSV,30,,,,,0;
CHA-COSSU:LCOSV,31,,,,,0;
CHA-COSSU:LCOSV,31,,,,,,"INTERNAL ONLY";
CHA-COSSU:LCOSV,32,1&&32;
CHA-COSSU:LCOSV,32,,,,,0;
CHA-COSSU:LCOSV,32,,,,,,"FULL ACCESS";
CHA-COSSU:LCOSD,1,1&&64;
CHA-COSSU:LCOSD,1,,,"LCR ATTENDANT FOR DATA";

ADD-WABE: 0,,,ATND,N,,,,,,,,;
ADD-WABE: 17&&18,,,STN,N,,,,,,,,;
ADD-WABE: 23,,,STN,N,,,,,,,,;
ADD-WABE: 4000&&5000,,,STN,N,,,,,,,,;
ADD-WABE: 5001,,,ATNDIND,N,,,,,,,,;
ADD-WABE: 5002,,6,ATNDDID,N,,,,,,,,;
ADD-WABE: 5002&&5003,,,ATND,N,,,,,,,,;
ADD-WABE: 5004&&5700,,,STN,N,,,,,,,,;
ADD-WABE: 77,,,STN,N,,,,,,,,;
ADD-WABE: 805,,,TIE,N,,,,,,,,;
ADD-WABE: 81,,,CO,N,,,,,,,,;
ADD-WABE: 9,,,CO,N,,,,,,,,;

ADD-SCSU:5036,1-1-1-0,ANATE,0,0,22,22,32,32,31,31,0,1,0,0,0,,,VAR,,,,ENGLISH,YES,,NO,,,,0,DIR,YES,NO,0,;

ADD-COT: 35,PRI&RCL&XFER&ANS&KNOR&CEBC&CBBN&CBFN&TRAI&BLOC&ATRS&TSCS&NOSD&NIN2&NPIS&NTON;
CHANGE-COT:35,COTADD,,INDEP,"TMANI";

ADD-COP:35,DTMF&ANS&SFRM&RLSA&BR64&TDED&NOAN&NO1A&DITW&TIM1&NSDL&IDP2&DTM1,TA,TA;
CHANGE-COP:35,COPADD,,,,INDEP,"TMANI";

ADD-BUEND:1,"BOF IN & OUT",15,0,*,1,ON,0,0,NEUTRAL;

ADD-TACSU:1-1-8-0,,35,35,0,0,22,1,1,,1,0," ",0,,2,1,EMPTY,0,NONE,NONE,0,EC&G711&G729AOPT," ",0,GDTR,0,,0,Y,TC,TMANIMSG,0,5036,0,0,1,0,1,0,MOSIG-DTMF,0-0,0,;

ADD-RICHT:LRTENEW,1,VCE,"BOF IN/OUT LINE",1,1-1-300,NO,NO,FIX,DIGITS,"TONE DIALLING ",PP80,,,,,NO,NO,"NEUTRAL",0,NEUTRAL,NO,NO,NO,NO,NO,NO,NO,NO;

ADD-LODR:2,,,,ECHO,2;
ADD-LODR:2,,,,END;
ADD-LODR:3,,,,ECHO,2;
ADD-LODR:3,,,,ECHO,3;
ADD-LODR:3,,,,END;

ADD-LDAT:1,VCE,1,,1,3,2,,1,EMPTY,WCHREG,,4,,,,,,,,,,,,;

ADD-LDPLN:LCRPATT,0,9-Z,0&1&2&3&4&5&6&7&8&9&10&11&12&13&14&15,1,,2,,,,N;
ADD-LDPLN:LCRPATT,0,81-X,0&1&2&3&4&5&6&7&8&9&10&11&12&13&14&15,1,,2,,,,N;
ADD-LDPLN:LCRPATT,0,81-X,0&1&2&3&4&5&6&7&8&9&10&11&12&13&14&15,1,,2,,,,N;
 
Hi Dear,
Please ignore my earlier post there are little bit typing mistake.

I tried to make a dial plan but can't success. My problem is call not passing through PSTN line. I have 2 LDPLN (9-Z and 81-X)for same route.
when using DPLN 9-Z
getting busy tone after dial the complete number (like 901730934209)

when using DPLN 81-X
getting busy tone when dial any digit after 81.

Here is my configuration,I would like to requested you please check the data and help me to solved the issue.

My System Is Openscape 4000 Eco Server (Duplex)V8 R2.22.0

Regards



ADD-BCSU:pER,1,1,1,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,1,2,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,1,3,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,1,4,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,1,5,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:SIUP,1,1,6,"Q2287-X ", ANIF&ANIF&ANIF&ANIF&ANIF&ANIF&ANIF&ANIF,0,5,0;
ADD-BCSU:pER,1,1,8,"Q2327-X100",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,1,9,"Q2327-X100",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,1,10,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,1,11,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,1,12,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,1,13,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,1,14,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,1,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,2,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,3,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,4,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,5,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,6,"Q2327-X100",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,8,"Q2327-X100",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,9,"Q2327-X100",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,10,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,11,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,12,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,13,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,2,14,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:IPGW,1,3,1,"Q2343-X ",1,0,21,,30,5,10,,,0,IPV4,NO,NO;
ADD-BCSU:pER,1,3,8,"Q2327-X100",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,3,10,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,3,11,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,3,12,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,3,13,"Q2227-X ",0,0,,,,,, ,0,,;
ADD-BCSU:pER,1,3,14,"Q2227-X ",0,0,,,,,, ,0,,;

ADD-COSSU:,5,,,,,,,,"";
CHA-COSSU:COS,5,TA&REVCHA&TNOTCR&COSXCD&MB&CFNR&VCE&FWDFAS;
CHA-COSSU:COS,5,FWDDIR&FWDBAS&FWDECA&FWDEXT&CCBS&CW&CTLS;
CHA-COSSU:COS,5,,NOCO&NOTIE;
CHA-COSSU:COS,5,,,NOCO&NOTIE;
ADD-COSSU:,6,,,,,,,,"TRACE COS";
CHA-COSSU:COS,6,TA&TNOTCR&COSXCD&MB&TRACE&CCBS&CW;
CHA-COSSU:COS,6,,NOCO&NOTIE;
CHA-COSSU:COS,6,,,NOCO&NOTIE;
ADD-COSSU:,10,,,,,,,,"";
CHA-COSSU:COS,10,TA&TNOTCR&COSXCD&MB&CFNR&VCE&FWDNWK&CFB;
CHA-COSSU:COS,10,CFSWF&FWDECA&FWDEXT&GRPCAL&HGICLD;
CHA-COSSU:COS,10,,NOCO&NOTIE;
CHA-COSSU:COS,10,,,NOCO&NOTIE;
ADD-COSSU:,15,,,,,,,,"GENERAL COS";
CHA-COSSU:COS,15,TA&TNOTCR&COSXCD&MB;
CHA-COSSU:COS,15,,NOCO&NOTIE;
CHA-COSSU:COS,15,,,NOCO&NOTIE;
ADD-COSSU:,22,,,,,,,,"";
CHA-COSSU:COS,22,TA&REVCHA&TNOTCR&CDRS&CDRSTN&CDRC&CDRIND&CDRINT;
CHA-COSSU:COS,22,COSXCD&MB&TRACE&CFNR&FWDNWK&CFB&FWDECA&FWDEXT;
CHA-COSSU:COS,22,CTLS;
CHA-COSSU:COS,22,,NOCO&NOTIE;
CHA-COSSU:COS,22,,,NOCO&NOTIE;
ADD-COSSU:,32,,,,,,,,"TRUNK COS";
CHA-COSSU:COS,32,TA&REVCHA&TNOTCR&CTLS;
CHA-COSSU:COS,32,,NOCO&NOTIE;
CHA-COSSU:COS,32,,,NOCO&NOTIE;
CHA-COSSU:LCOSV,1,,2&&64;
CHA-COSSU:LCOSV,1,,,,,0;
CHA-COSSU:LCOSV,1,,,,,,"TIE ACCESS";
CHA-COSSU:LCOSV,2,1&&2;
CHA-COSSU:LCOSV,2,,,,,0;
CHA-COSSU:LCOSV,2,,,,,,"LOCAL ACCESS";
CHA-COSSU:LCOSV,3,1&&3;
CHA-COSSU:LCOSV,3,,,,,0;
CHA-COSSU:LCOSV,3,,,,,,"LOCAL+MOBILE ACCESS";
CHA-COSSU:LCOSV,4,1&&4;
CHA-COSSU:LCOSV,4,,,,,0;
CHA-COSSU:LCOSV,4,,,,,,"NWD ACCESS";
CHA-COSSU:LCOSV,5,1&&5;
CHA-COSSU:LCOSV,5,,,,,0;
CHA-COSSU:LCOSV,5,,,,,,"ISD ACCESS";
CHA-COSSU:LCOSV,6,,,,,0;
CHA-COSSU:LCOSV,7,,,,,0;
CHA-COSSU:LCOSV,8,,,,,0;
CHA-COSSU:LCOSV,9,,,,,0;
CHA-COSSU:LCOSV,10,1&&10;
CHA-COSSU:LCOSV,10,,,,,0;
CHA-COSSU:LCOSV,10,,,,,,"OPERATOR";
CHA-COSSU:LCOSV,11,1&&5&10&&11;
CHA-COSSU:LCOSV,11,,,,,0;
CHA-COSSU:LCOSV,11,,,,,,"CEO DIRECT T&T IN";
CHA-COSSU:LCOSV,12,1&&5&10&12;
CHA-COSSU:LCOSV,12,,,,,0;
CHA-COSSU:LCOSV,12,,,,,,"DMS DIRECT T&T IN";
CHA-COSSU:LCOSV,13,1&&5&13;
CHA-COSSU:LCOSV,13,,,,,0;
CHA-COSSU:LCOSV,13,,,,,,"MD DIRECT T&T IN";
CHA-COSSU:LCOSV,14,,,,,0;
CHA-COSSU:LCOSV,15,,,,,0;
CHA-COSSU:LCOSV,16,1&&10&16;
CHA-COSSU:LCOSV,16,,,,,0;
CHA-COSSU:LCOSV,16,,,,,,"OPERATOR+ MOBILE";
CHA-COSSU:LCOSV,17,,,,,0;
CHA-COSSU:LCOSV,18,,,,,0;
CHA-COSSU:LCOSV,19,,,,,0;
CHA-COSSU:LCOSV,20,,,,,0;
CHA-COSSU:LCOSV,21,,,,,0;
CHA-COSSU:LCOSV,22,,,,,0;
CHA-COSSU:LCOSV,23,,,,,0;
CHA-COSSU:LCOSV,24,,,,,0;
CHA-COSSU:LCOSV,25,,,,,0;
CHA-COSSU:LCOSV,26,,,,,0;
CHA-COSSU:LCOSV,27,,,,,0;
CHA-COSSU:LCOSV,28,,,,,0;
CHA-COSSU:LCOSV,29,,,,,0;
CHA-COSSU:LCOSV,30,,,,,0;
CHA-COSSU:LCOSV,31,,,,,0;
CHA-COSSU:LCOSV,31,,,,,,"INTERNAL ONLY";
CHA-COSSU:LCOSV,32,1&&32;
CHA-COSSU:LCOSV,32,,,,,0;
CHA-COSSU:LCOSV,32,,,,,,"FULL ACCESS";
CHA-COSSU:LCOSD,1,1&&64;
CHA-COSSU:LCOSD,1,,,"LCR ATTENDANT FOR DATA";

ADD-WABE: 0,,,ATND,N,,,,,,,,;
ADD-WABE: 17&&18,,,STN,N,,,,,,,,;
ADD-WABE: 23,,,STN,N,,,,,,,,;
ADD-WABE: 4000&&5000,,,STN,N,,,,,,,,;
ADD-WABE: 5001,,,ATNDIND,N,,,,,,,,;
ADD-WABE: 5002,,6,ATNDDID,N,,,,,,,,;
ADD-WABE: 5002&&5003,,,ATND,N,,,,,,,,;
ADD-WABE: 5004&&5700,,,STN,N,,,,,,,,;
ADD-WABE: 77,,,STN,N,,,,,,,,;
ADD-WABE: 805,,,TIE,N,,,,,,,,;
ADD-WABE: 81,,,CO,N,,,,,,,,;
ADD-WABE: 9,,,CO,N,,,,,,,,;

ADD-SCSU:5036,1-1-1-0,ANATE,0,0,22,22,32,32,31,31,0,1,0,0,0,,,VAR,,,,ENGLISH,YES,,NO,,,,0,DIR,YES,NO,0,;

ADD-COT: 35,PRI&RCL&XFER&ANS&KNOR&CEBC&CBBN&CBFN&TRAI&BLOC&ATRS&TSCS&NOSD&NIN2&NPIS&NTON;
CHANGE-COT:35,COTADD,,INDEP,"TMANI";

ADD-COP:35,DTMF&ANS&SFRM&RLSA&BR64&TDED&NOAN&NO1A&DITW&TIM1&NSDL&IDP2&DTM1,TA,TA;
CHANGE-COP:35,COPADD,,,,INDEP,"TMANI";

ADD-BUEND:1,"BOF IN & OUT",15,0,*,1,ON,0,0,NEUTRAL;

ADD-TACSU:1-1-8-0,,35,35,0,0,22,1,1,,1,0," ",0,,2,1,EMPTY,0,NONE,NONE,0,EC&G711&G729AOPT," ",0,GDTR,0,,0,Y,TC,TMANIMSG,0,5036,0,0,1,0,1,0,MOSIG-DTMF,0-0,0,;

ADD-RICHT:LRTENEW,1,VCE,"BOF IN/OUT LINE",1,1-1-300,NO,NO,FIX,DIGITS,"TONE DIALLING ",PP80,,,,,NO,NO,"NEUTRAL",0,NEUTRAL,NO,NO,NO,NO,NO,NO,NO,NO;

ADD-LODR:2,,,,ECHO,2;
ADD-LODR:2,,,,END;
ADD-LODR:3,,,,ECHO,2;
ADD-LODR:3,,,,ECHO,3;
ADD-LODR:3,,,,END;

ADD-LDAT:1,VCE,1,,1,3,2,,1,EMPTY,WCHREG,,4,,,,,,,,,,,,;

ADD-LDPLN:LCRPATT,0,9-Z,0&1&2&3&4&5&6&7&8&9&10&11&12&13&14&15,1,,2,,,,N;
ADD-LDPLN:LCRPATT,0,81-X,0&1&2&3&4&5&6&7&8&9&10&11&12&13&14&15,1,,2,,,,N;
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top