ls/ds vs. T1 1

[RYLSFAN]

MICS w/ 6.1 and fractional T1 (6 channels)no pri, with 1 ls/ds card. calls over ls/ds are able to be connected to the vmail with F986, but calls on the T1 will not, they just sit there. So we upgrade to 7.0 and still the same problem. Any call on the T1 can not be transfered to mail.

please help

tia

Thats not my fastball, thats my hurry up and get by you pitch... Satchel Paige

 

[hawks]

How is the T1 set up?

 

[RYLSFAN]

default except changed to E&M.

Thats not my fastball, thats my hurry up and get by you pitch... Satchel Paige

 

[RYLSFAN]

T1
001-024
Disco Timer:460
TIA-547A
ISDN
ESF
CSU line bld: 0
B8zs
Primary Clocking


calls come in and out just fine, but not rec by the vmail...

Thats not my fastball, thats my hurry up and get by you pitch... Satchel Paige

 

[webephones]

are we setting trunks to answer ...what release is vm"must be 4.1"

If i lived in colorado i would be skiing already.But i dont so its a long 4 weeks till opening day.

 

[hawks]

I was just wondering if it has anything to do with trunk supervision. can you turn off supervision on one of your copper Trunks and then try it?

 

[RYLSFAN]

the vmail is a flash 2.01, the system allows the vmail full functionality, just not over the T1.... driving me crazy..er

Thats not my fastball, thats my hurry up and get by you pitch... Satchel Paige

 

[webephones]

do we have atleast 2 icom buttons on the phone

If i lived in colorado i would be skiing already.But i dont so its a long 4 weeks till opening day.

 

[RYLSFAN]

2 intercoms, no way to manipulate disco supervision, and the lines are set to auto answer.

Thats not my fastball, thats my hurry up and get by you pitch... Satchel Paige

 

[webephones]

try manual

If i lived in colorado i would be skiing already.But i dont so its a long 4 weeks till opening day.

 

[hawks]

You can go into trunk programming and turn off supervision do a test then turn it back on. Just remember when you turn it on and off your trunks will be down for approximately 2 minutes.

 

[RYLSFAN]

i have tried manual answer and get the same result, it just rings in on the intercom instead of the target line.

as for the programming of the supervision, i'm not sure i follow. I didn't think you could change the disco supo on an E&M line????

thanks for all the help by the way...

Thats not my fastball, thats my hurry up and get by you pitch... Satchel Paige

 

[hawks]

No I was talking about changing it on the Loop start lines for a test. You said it worked on the copper trunks.

 

[RYLSFAN]

i c. let me try that...

Thats not my fastball, thats my hurry up and get by you pitch... Satchel Paige

 

[webephones]

what exactley does the call do when f986 is pressed

If i lived in colorado i would be skiing already.But i dont so its a long 4 weeks till opening day.

 

[RYLSFAN]

vmail transfer works when copper lines are supervised and unsupervised. STUMPED.

Thats not my fastball, thats my hurry up and get by you pitch... Satchel Paige

 

[RYLSFAN]

when on the T, as a caller hear nothing, you never leave the called party. as the called party you press F986 and F986 shows up in the window for a half second and then the line display returns.

Thats not my fastball, thats my hurry up and get by you pitch... Satchel Paige

 

[hawks]

I'll try to set it up in the Lab tomorrow

 

[RYLSFAN]

reading old order from MCI this is a LD T sharing pipe with Frame Network.... mean anything to anyone?

Thats not my fastball, thats my hurry up and get by you pitch... Satchel Paige

 

[RYLSFAN]

here is what i received from MCI the day of install:

Additional Comments: Installing a new T-1 with voice and data. The T-1 will be configured as follows: B8zs/esf, E&M Wink (no DNIS). Channel assignment will be:

Chan1-8 will be INBOUND, Channel 9-16 will be OUTBOUND 17-20 Unassigned (reserved for growth) and 256k Frame will be on channel 21-24. We will order a new

Frame port and coordinate to move the PVC.



Thats not my fastball, thats my hurry up and get by you pitch... Satchel Paige