Linking Nortel with Definity

[seetu]

I wish to link Definity with Nortel Meridian swithc using ISDN PRI and Q-SIg protocol. Pleas advise what type of interface setting I should use for porper linking. I have problem in calling Nortel switch from Definity. Reverse is OK.
What should be programmed for D-channel IFC? Please advise.

 

[cmawbey]

hi this is my setup.

This is how i have set it up via a PRI Interface (E1, 2MBit, 30 CHannels x 64K).

Loop Timers

LOOP 3
MFF CRC
ACRC YES
ALRM REG
RAIE NO
G1OS YES
SLP 5 24 H 30 1 H
BPV 128 122
CRC 201 97
FAP 28 1
RATS 10
GP2 20 100 S 12 S 12 S 4 S
MNG1 15 M
NCG1 15 M
OSG1 15 M
MNG2 15 S
NCG2 15 S
OSG2 15 S
PERS 50
CLRS 50
OOSC 5


QSIG D-Channel Configuration

ADAN DCH 13
CTYP MSDL
CARD 03
PORT 1
DES QSIG_TIE
USR PRI
DCHL 3
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
NASA NO
IFC ESIG
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE NET
CNEG 1
RLS ID **
RCAP COLP
MBGA NO



OVLR YES
DIDD 0
OVLS YES
OVLT 1
T310 120
T200 3
T203 10
N200 3
N201 260
K 7


Route Data Block QSIG

ROUT 3
DES QSIG
TKTP TIE
ESN NO
RPA NO
CNVT NO
SAT NO
RCLS INT
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC ESIG
SBN NO
PNI 12345
NCNA NO
NCRD NO
CTYP UKWN
INAC NO
ISAR NO
TGAR 0
CPFXS YES
ADDP YES
DSEL 3VCE
PTYP DTT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 6003
TCPP NO
TARG
BILN NO
OABS


INST
IDC YES
DCNO 3 *
NDNO 3
DEXT NO
DNAM NO
SIGO STD
MFC NO
ICIS YES
OGIS YES
TIMR ICF 512
OGF 512
EOD 3968
NRD 10112
DDL 70
ODT 3840
RGV 640
GTO 896
GTI 896
SFB 3
NBS 2048
NBL 4096
IENB 5
TFD 0
VSS 0
VGD 6
DTD NO
SCDT NO
2 DT NO
DRNG YES
NDRI 00
CDR NO
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS YES
MRT 10
PANS YES
EQAR NO
FRL 0 7
FRL 1 7
FRL 2 7
FRL 3 7
FRL 4 7
FRL 5 7
FRL 6 7
FRL 7 7
OHQ NO
OHQT 00
AUTH NO
TTBL 0


PLEV 2
OPR NO
ALRM NO
ART 0
PECL NO
DCTI 0
TIDY 9987 3
SGRP 0
CAC 3
ANDN
RDNL 4
AACR NO


Trunk Data Block QSIG

TN 003 01
TYPE TIE
CDEN SD
CUST 0
TRK PRI2
PDCA 1
PCML A
NCOS 7
RTMB 3 1
B-CHANNEL SIGNALING
TGAR 0
CLS TLD DIP WTA LPR APN THFD XREP BARD
P10 VNL
TKID
FCAR NO

good luck



Colin

 

[seetu]

Thanks Cmawbey , for your reply.
But it seems that your set up is for linking two Nortel switches. I want have set up for linking with Definity,Avaya switch.

 

[senk1s]

if the G3 is blocking the outgoing calls ... maybe u can try posting in the Definity forum ...

 

[bickles]

Seetu,

I too am having trouble with a qsig link between Meridian and Avaya. In answer to your question I can tell you that we are using ESIG.

I need to get qsig route optimistation working between the two but do not know how to setup the PINX DN within the Avaya so that only the pinx dn is sent and any prefixes (AAR) used for routing the call are stripped.

I would be only too happy to share any information if it means progressing this!

 

[seetu]

Hi Bickles,
Now I am though with the link using ESS4 as IFC , but getting only number not name.
Avaya doesn't send the AAR digits. You can delete any extra digits in Change route pattern command.
What I found is Nortel is sending additional prefix digits and they have to be absorbed in avaya in trunk group conifguration. Other wise calls go to wrong numbers.