Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

LFAS error on PRI2

Status
Not open for further replies.

AC427

Technical User
Mar 12, 2007
70
GB
Hi,

I have a PRI circuit between 2 Option11s and am getting the following error at one end

PRI2 LOOP 1 - ENBL
REF CLK: ENBL
TRACKING
SERVICE RESTORE: YES
ALARM STATUS: OOS LOCAL ALARM : LFAS
CH 01 - DSBL TIE VOD * CH 02 - DSBL TIE VOD *
CH 03 - DSBL TIE VOD * CH 04 - DSBL TIE VOD *
CH 05 - DSBL TIE VOD * CH 06 - DSBL TIE VOD *
CH 07 - DSBL TIE VOD * CH 08 - DSBL TIE VOD *
CH 09 - DSBL TIE VOD * CH 10 - DSBL TIE VOD *
CH 11 - DSBL TIE VOD * CH 12 - DSBL TIE VOD *
CH 13 - DSBL TIE VOD * CH 14 - DSBL TIE VOD *
CH 15 - DSBL TIE VOD * CH 16 - DSBL TIE VOD *
CH 17 - DSBL TIE VOD * CH 18 - DSBL TIE VOD *
CH 19 - DSBL TIE VOD * CH 20 - DSBL TIE VOD *
CH 21 - DSBL TIE VOD * CH 22 - DSBL TIE VOD *
CH 23 - DSBL TIE VOD * CH 24 - DSBL TIE VOD *
CH 25 - DSBL TIE VOD * CH 26 - DSBL TIE VOD *
CH 27 - DSBL TIE VOD * CH 28 - DSBL TIE VOD *
CH 29 - DSBL TIE VOD * CH 30 - DSBL TIE VOD *
CH 31 - DCH 10


and LCNT shows

.lcnt


PRI2 TRK LOOP 1
MNT NNDC NNC OOS
BPV- 000 000 000 000
FAP- 000 000 000 000
SLP- 000 000 000 000
CRC- 000 000 000 000
G2 - 000 000 000 002
MAINT NONEWCALL UNAVAIL SEVERE
TOTAL 24HR BPV - 000000000 000000000 000000000 000000000
TOTAL 24HR CRC - 000000000 000000000 000000000 000000000
TOTAL 24HR FAP - 000000000 000000000 000000000 000000000
TOTAL 24HR SLPREP - 000000000
TOTAL 24HR SLPDEL - 000000000
TOTAL 24 HOUR G2 AIS -000000000
TOTAL 24 HOUR G2 LFAS -000000002
TOTAL 24 HOUR G2 LMAS -000000000
TOTAL 24 HOUR G2 RAI -000000000
TOTAL 24 HOUR G2 LOS -000000000
TOTAL 24 HOUR G2 RAIE -000000000


The LFAS error increases by 1 each time i reset the card and goes idle for a few seconds before disabling again.

Would the Loss of Frame Allignment Signal be coming from the curcuit provider?

Regards

 
Have you checked the status of DCH 10 in LD 96, theres no point in checking the status of the Channels until you know the DCH has established.

LD 96

STAT DCH

If this is a previously working circuit, and the DCH is not establishing, your first option should be to contact the service provider.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top