Hi all,
I have an LDK-20 (D) system with 2 BRI ports that I don't use, an LCOB4, and a VOIM with VOIU card (not installed VOIU at the time of this post)
As I do not use the BRI ports, they are disabled by programming and in CO Group 9.
Lines 5-7 on the LCOB card are connected to VoIP ATAs to give me VoIP lines
Line 8 is the physical landline, and we generally do not dial out on it
Lines 9-11 are the VOIM channels
Line 12 is not enabled as it is serving as a IP line for Phontage, station 82 (IP Phone)
---
My question(s) are as follows:
I have multiple phone numbers through my SIP Provider DID Logic. There are 3 phone numbers
+61 3 xxxx x984 - Local AU number
+81 3 xxxx x615 - Tokyo, Japan number
+1 435 xxx x289 - UT, USA number
Under the current setup I have, LCR will automatically send calls that are going out to USA (Signalled by 4411 1) via Line 5, which is where the ATA that displays the USA number is. All other calls go via the VOIM (which is a good thing), but the catch is it only shows my AU phone number as the caller ID (Not always a good thing)
My problem is that I want to be able to use the VOIM for multiple phone numbers both IN and OUT of the system.
For example: If I were to dial my friend in Osaka, Japan - I want the system to be able to dial 0, then the number, and then use the appropriate SIP sub-account which shows the Japan Caller ID on it.
DIDLogic uses one MAIN account for billing you, and then you can set up "sub-accounts" that are intended for you to be able to route calls in from your DIDs to destinations, and displaying CLI and so on..
I want to know how to use several sub-accounts and have LCR be able to factor this in.
All my calls are made from the 1 station, Station 12 usually.
I see in LDK-PCADMIN that there is facility to be able to dial out with multiple SIP accounts, but in Station Programming, you can only assign a station to a single SIP User ID.
Thanks in advance!
Angel
I have an LDK-20 (D) system with 2 BRI ports that I don't use, an LCOB4, and a VOIM with VOIU card (not installed VOIU at the time of this post)
As I do not use the BRI ports, they are disabled by programming and in CO Group 9.
Lines 5-7 on the LCOB card are connected to VoIP ATAs to give me VoIP lines
Line 8 is the physical landline, and we generally do not dial out on it
Lines 9-11 are the VOIM channels
Line 12 is not enabled as it is serving as a IP line for Phontage, station 82 (IP Phone)
---
My question(s) are as follows:
I have multiple phone numbers through my SIP Provider DID Logic. There are 3 phone numbers
+61 3 xxxx x984 - Local AU number
+81 3 xxxx x615 - Tokyo, Japan number
+1 435 xxx x289 - UT, USA number
Under the current setup I have, LCR will automatically send calls that are going out to USA (Signalled by 4411 1) via Line 5, which is where the ATA that displays the USA number is. All other calls go via the VOIM (which is a good thing), but the catch is it only shows my AU phone number as the caller ID (Not always a good thing)
My problem is that I want to be able to use the VOIM for multiple phone numbers both IN and OUT of the system.
For example: If I were to dial my friend in Osaka, Japan - I want the system to be able to dial 0, then the number, and then use the appropriate SIP sub-account which shows the Japan Caller ID on it.
DIDLogic uses one MAIN account for billing you, and then you can set up "sub-accounts" that are intended for you to be able to route calls in from your DIDs to destinations, and displaying CLI and so on..
I want to know how to use several sub-accounts and have LCR be able to factor this in.
All my calls are made from the 1 station, Station 12 usually.
I see in LDK-PCADMIN that there is facility to be able to dial out with multiple SIP accounts, but in Station Programming, you can only assign a station to a single SIP User ID.
Thanks in advance!
Angel