Keep having to restart program units TLP60 & SLP60

[GFDANNHAUSER]

Good day

Anyone have some advise for me?
We have a E1 circuits going to Cisco routers, and at least twice a day I must restart the program units, TLP60 & SLP60.

the lines show Idle and Busy, and it is usually on the first and last 3 trunks.

Best regards

 

[Satellite1900]

shows the configuration of ROU and DEST

\Satellite1900

 

[GFDANNHAUSER]

<ROCAP:ROU=158;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
158 7110000001000010 5 3110000001 0 30 128 00040414 511110120031 111111

END

<RODAP:ROU=158;
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
158 SL60 H'00000310 H'15420000 H'46300000 NO

END

<RODDPEST=16;
EXTERNAL DESTINATION ROUTE DATA
DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE
16 158 1 26061000000002500060000000 0 1 0

END

 

[himdp]

What revision of software? Do you have many lost signals (HIMDP)?

 

[GFDANNHAUSER]

Hi HIMDP and Satellite

its TSWsp03, will upgrade, its a 13 LIM system with remote LIMS.

I keep getting alarm code 2, and that is when it happens.
It seems the programs execution times out.
This only started recently, we had a link down, and there was rerouting done on the routers, I suspect trunks mismatching.

 

[Satellite1900]

This works fine:
ROCAI:ROU=158,SEL=7110000000000010,TRAF=00040414,TRM=5,SERV=3110000011,BCAP=111111,SIG=111110000031;
RODAI:ROU=158,TYPE=SL60,VARC=00000310,VARI=15400000,VARO=06300000;
RODDIEST=16,ROU=158,SRT=1,ADC=160600000000025010600100110;
in the case also controls:
aspacarnum=66,parval=1;
aspacarnum=223,parval=7;

\Satellite1900

 

[GFDANNHAUSER]

Thank you Satellite.
Will give it a go.

 

[himdp]

Print HIMDP will give you more info for you error code 2. SP 3 is a little out of date

 

[GFDANNHAUSER]

Hi HIMDP
Will do as soon as it happens again.
Br

 

[Satellite1900]

Just To complete the information
the configuration that I have written is of a system TSW SP3, it works correctly

\Satellite1900

 

[GFDANNHAUSER]

Thank you Satellite

 

[GFDANNHAUSER]

Morning guys

HIMDP for you:
<HIMDP:LIM=13&4&7;

DIAGNOSTICS FROM OPERATING SYSTEM
TIME DATE
08:12:35 19JUL13
DIAGNOSTICS FROM LIM 004, LAST HIREI: 14:52:00 18JUL13

TIME DATE ERROR CODE
05:47:35 19JUL13 H'10
EXECUTION TIMEOUT
LOGICAL PROGRAM ERROR ADDRESS = 0201F91C
ENTER
SWSW A-LEVEL SIGNAL CLRLIN (H'005F)
FROM SLP60 (H'37B) EXE A IN LIM 004
TO TLP60 (H'3BD) EXE A IN LIM 004
NUMBER OF DATA BYTES IN SIGNAL = 6
WITH 0 1 2 3 4 5 6 7 8 9
000 EF 1E 0F 00 00 00

USER STACK DUMP
0 1 2 3 4 5 6 7 8 9 A B C D E F
02 01 BF 9C 02 01 F6 5E 02 00 52 AA

TIME DATE ERROR CODE
15:11:48 18JUL13 H'14
JUMP TO ILLEGALSTATE
LOGICAL PROGRAM ERROR ADDRESS = 02066BC0
ENTER
SWSW A-LEVEL SIGNAL TRUTOTRUCAL (H'002C)
FROM TLP60 (H'3BD) EXE A IN LIM 004
TO SLP60 (H'37B) EXE A IN LIM 004
NUMBER OF DATA BYTES IN SIGNAL = 6
WITH 0 1 2 3 4 5 6 7 8 9
000 E6 38 00 01 03 01

USER STACK DUMP
0 1 2 3 4 5 6 7 8 9 A B C D E F
02 02 20 9C
DIAGNOSTICS FROM LIM 007, LAST HIREI: 14:52:00 18JUL13

TIME DATE ERROR CODE
23:23:28 18JUL13 H'31
WRONG SIGNAL ENTRY LEVEL
LOGICAL PROGRAM ERROR ADDRESS = 02000758
ENTER
HWSW B-LEVEL SIGNAL FIXFNCACT (H'0004)
FROM DEVICE EQU NO 7-0-40-29
TO KLP1T (H'1CD) EXE A IN LIM 007
NUMBER OF DATA BYTES IN SIGNAL = 8
WITH 0 1 2 3 4 5 6 7 8 9
000 02 26 07 FF FF 64 FF D5
STACK ADDRESS = 00000000
SIGNAL SEND ADDRESS = 00000000


TIME DATE ERROR CODE
21:07:42 18JUL13 H'30
WRONG SIGNAL ENTRY TYPE
HW SIGNAL ENTERED IN SW SIGNAL ENTRY
LOGICAL PROGRAM ERROR ADDRESS = 0203F9FA
ENTER
HWSW B-LEVEL SIGNAL MEWKEYFCNINFO (H'00FF)
FROM DEVICE EQU NO 7-0-40-29
TO KLP1T (H'1CD) EXE A IN LIM 007
NUMBER OF DATA BYTES IN SIGNAL = 32
WITH 0 1 2 3 4 5 6 7 8 9
000 02 26 FF 44 FF 10 FF FF 44 FF
010 09 84 FF 89 FF FF 4B 48 EE FF
020 22 FF FF 09 44 FF 16 00 FF CC
030 FF FF
STACK ADDRESS = 00000000
SIGNAL SEND ADDRESS = 00000000


TIME DATE ERROR CODE
17:44:20 18JUL13 H'10
EXECUTION TIMEOUT
LOGICAL PROGRAM ERROR ADDRESS = 0201F962
ENTER
SWSW A-LEVEL SIGNAL CLRLIN (H'005F)
FROM SLP60 (H'37B) EXE A IN LIM 007
TO TLP60 (H'3BD) EXE A IN LIM 007
NUMBER OF DATA BYTES IN SIGNAL = 6
WITH 0 1 2 3 4 5 6 7 8 9
000 3F 37 0F 00 00 00
STACK ADDRESS = 02011E36
SIGNAL SEND ADDRESS = 02047720

USER STACK DUMP
0 1 2 3 4 5 6 7 8 9 A B C D E F
02 01 BF 9C 02 01 F6 5E 02 00 52 AA

TIME DATE ERROR CODE
17:37:27 18JUL13 H'11
SIGNAL ENTRY NOT FOUND
SINGLE BUFFERED SIGNAL
ENTER
HWSW B-LEVEL SIGNAL *************** (H'0000)
FROM DEVICE EQU NO 7-0-40-13
TO KLP1T (H'1CD) EXE A IN LIM 007
NUMBER OF DATA BYTES IN SIGNAL = 56
WITH 0 1 2 3 4 5 6 7 8 9
000 02 36 FF FF D8 57 FF E8 FF FF
010 57 75 FF 85 FF 37 FF FF 40 FF
020 13 FF E8 28 CC FF 45 CD FF C2
030 D1 44 FF 33 FF FF 98 FF 19 24
040 FF 00 FF FF 22 22 FF 44 FF FF
050 22 11 68 38 FF FF
STACK ADDRESS = 00000000
SIGNAL SEND ADDRESS = 00000000


TIME DATE ERROR CODE
17:32:29 18JUL13 H'30
WRONG SIGNAL ENTRY TYPE
HW SIGNAL ENTERED IN SW SIGNAL ENTRY
LOGICAL PROGRAM ERROR ADDRESS = 0203F9FA
ENTER
HWSW A-LEVEL SIGNAL MEWKEYFCNINFO (H'00FF)
FROM DEVICE EQU NO 7-2-30-10
TO KLP1T (H'1CD) EXE A IN LIM 007
NUMBER OF DATA BYTES IN SIGNAL = 40
WITH 0 1 2 3 4 5 6 7 8 9
000 01 DE 08 FF A1 01 FF 24 FF FF
010 3C FF 56 40 FF 13 48 74 10 FF
020 12 FF FF AE FF 5E FF 26 8A FF
030 72 FF FF 60 FF FD 1E E1 66 64
STACK ADDRESS = 00000000
SIGNAL SEND ADDRESS = 00000000

DIAGNOSTICS FROM LIM 013, LAST HIREI: 14:52:00 18JUL13

TIME DATE ERROR CODE
17:10:41 18JUL13 H'10
EXECUTION TIMEOUT
LOGICAL PROGRAM ERROR ADDRESS = 0201BF84
ENTER
SWSW A-LEVEL SIGNAL CLRLIN (H'005F)
FROM SLP60 (H'37B) EXE A IN LIM 013
TO TLP60 (H'3BD) EXE A IN LIM 013
NUMBER OF DATA BYTES IN SIGNAL = 6
WITH 0 1 2 3 4 5 6 7 8 9
000 06 AD 0F 00 00 00
STACK ADDRESS = 02012806
SIGNAL SEND ADDRESS = 02047720

USER STACK DUMP
0 1 2 3 4 5 6 7 8 9 A B C D E F
02 01 F6 5E 02 00 52 AA

END
<ALLOP:CODE=2;
ALARM LOG
IDENTITY: UNMIL-HQ
VERSION: CXP1010101/4/TSWSP03/R4A

DATE: 19JUL13 TIME: 08:12:45
CLASS: 1
2 EXECUTION TIMEOUT
DATE TIME ALP NOIF UNIT EQU INF1
18JUL13 17:10:41 47 1 TLP60 013-0-**-** 0

2 EXECUTION TIMEOUT
DATE TIME ALP NOIF UNIT EQU INF1
18JUL13 17:44:19 50 1 TLP60 007-0-**-** 0

2 EXECUTION TIMEOUT
DATE TIME ALP NOIF UNIT EQU INF1
19JUL13 05:47:34 64 1 TLP60 004-0-**-** 0


LAST ALREI: 18JUL13, 14:51:53

END

 

[himdp]

Hi,
Did the above happen after you implemented the route data changes suggested by satellite1900?
If you have changed the data and the problem is still happening, then I can only suggest an upgrade to the latest service pack.

The lost signals in HIMDP which are causing the circuits to hang are CLRLIN (Clear Line) from SLP60 to TLP60. As these signals are thrown in the trash because of EXECUTION TIMEOUT (program loop) the clear down sequence is broken and the circuits hang. A patch would be required to fix this issue and an upgrade will probably fix this.

 

[GFDANNHAUSER]

Hi HIMDP

I did do a additional route yesterday, I inherited this system, so I programmed my own route as I always have for Cisco, I move the circuit this morning, lets see if it will sort out the signalling.
I agree the clearing signal has an issue, and as I said before, this started happening after the router guys reconfigured the routing due to a router that went down.

Will keep you guys updated!

Thank you!

 

[Satellite1900]

Let us know how are the rehearsals with the configuration that I gave you yesterday.
But if you say that the problem originated with the new configuration of the router, then I do not think that the problem is the pbx Ericsson
update us

\Satellite1900