Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations TouchToneTommy on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

ITG line card problem

Status
Not open for further replies.

pbxtester

Technical User
Sep 13, 2007
27
DK
Hi there

I am trying to install an ITG card in my Meridian system, but I am having some problems doing that.

On my call server I get the following:

.stat <cardno>
00 = UNIT 00 = DSBL (TRK)(IPTN UNREG OWK /OWK )
01 = UNIT 01 = DSBL (TRK)(IPTN UNREG OWK /OWK )
02 = UNIT 02 = DSBL (TRK)(IPTN UNREG OWK /OWK )
03 = UNIT 03 = DSBL (TRK)(IPTN UNREG OWK /OWK )
04 = UNIT 04 = DSBL (TRK)(IPTN UNREG OWK /OWK )
05 = UNIT 05 = DSBL (TRK)(IPTN UNREG OWK /OWK )
06 = UNIT 06 = DSBL (TRK)(IPTN UNREG OWK /OWK )
07 = UNIT 07 = DSBL (TRK)(IPTN UNREG OWK /OWK )
08 = UNIT 08 = DSBL (TRK)(IPTN UNREG OWK /OWK )
09 = UNIT 09 = DSBL (TRK)(IPTN UNREG OWK /OWK )
10 = UNIT 10 = DSBL (TRK)(IPTN UNREG OWK /OWK )
11 = UNIT 11 = DSBL (TRK)(IPTN UNREG OWK /OWK )
12 = UNIT 12 = DSBL (TRK)(IPTN UNREG OWK /OWK )
13 = UNIT 13 = DSBL (TRK)(IPTN UNREG OWK /OWK )
14 = UNIT 14 = DSBL (TRK)(IPTN UNREG OWK /OWK )
15 = UNIT 15 = DSBL (TRK)(IPTN UNREG OWK /OWK )
16 = UNIT 16 = DSBL (TRK)(IPTN UNREG OWK /OWK )
17 = UNIT 17 = DSBL (TRK)(IPTN UNREG OWK /OWK )
18 = UNIT 18 = DSBL (TRK)(IPTN UNREG OWK /OWK )
19 = UNIT 19 = DSBL (TRK)(IPTN UNREG OWK /OWK )
20 = UNIT 20 = DSBL (TRK)(IPTN UNREG OWK /OWK )
21 = UNIT 21 = DSBL (TRK)(IPTN UNREG OWK /OWK )
22 = UNIT 22 = DSBL (TRK)(IPTN UNREG OWK /OWK )
23 = UNIT 23 = DSBL (TRK)(IPTN UNREG OWK /OWK )
24 = UNIT 24 = DSBL (TRK)(IPTN UNREG OWK /OWK )
25 = UNIT 25 = DSBL (TRK)(IPTN UNREG OWK /OWK )
26 = UNIT 26 = DSBL (TRK)(IPTN UNREG OWK /OWK )
27 = UNIT 27 = DSBL (TRK)(IPTN UNREG OWK /OWK )
28 = UNIT 28 = DSBL (TRK)(IPTN UNREG OWK /OWK )
29 = UNIT 29 = DSBL (TRK)(IPTN UNREG OWK /OWK )
30 = UNIT 30 = DSBL (TRK)(IPTN UNREG OWK /OWK )
31 = UNIT 31 = DSBL (TRK)(IPTN UNREG OWK /OWK )

Why do I get an error saying that the IPTN is UNREG? Also, the general state of the card is UNEQUIP - what does that mean?

Thank you very much!
 
it means that no one had installed it.. built trunks, added an ip address.. it's been plugged in and added to the cequ, nothing more.. about the same theory as buying new brakes for your car and them not helping your braking distance because they are out of the box and on the seat beside you... look at your ld 117 commands, ld 16 and load 14

john poole
bellsouth business
columbia,sc
 
Why do I get:

stat <cardno>
00 = UNIT 00 = DSBL (TRK)(IPTN UNREG OWK /OWK )
01 = UNIT 01 = DSBL (TRK)(IPTN UNREG OWK /OWK )

when I get this:

stat <cardno> <unitno>
IDLE

??
 
In LD 20 I PRT the VGW and get

DES LINE
TN 020 0 00 0
TYPE VGW
CUST 0
XTRK MC32
ZONE 001

.......

and some 30 more. The card isn't installed yet or?

Thank you very much.
 
First off, you're installing an SMC, not an ITG -- 32 ports = SMC.

Did you configure the ELAN? If the card does not communicate with the PBX, it won't register.
 
Ahh, ok - thank you for the info :)

Yeah, the ELAN is configured. If I run the itgCardShow command on the ITG card it shows everything - the same if I run the pbxLinkShow command.

 
Installing VGW required you have already a Signaling server installed.

As gwebster says, read NTPs first. Explanations here will be too long
 
I am sorry - I do not think I understand. In my setup I do not need a Sig. Server in order to get this working.

I am reading 553-3001-363 og 553-3001-365, but I cannot make it work!
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top