Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

issues adding DLOP in CS1000E 5.5

Status
Not open for further replies.

Crowtalks

Technical User
Mar 19, 2005
1,523
US
I am adding another T1/PRI to my switch and going to LD17 - CEQU - DLOP, when I get to DTIC it will not accept my loop # where I am going to install the TMDI card...in fact it won't accept any of my SUPLs. I wonder what I'm missing?

Jim

"If I had known it would turn out like this, I would have became a locksmith" Albert Einstein

NCSS NCTS NCTE CS1000E
Mitel 3300 4.2 basic & advanced, 5000 4.0, NuPoint I&M 4.2
 
It's the same...I go through all the config but the very last entry...DTIC is being difficult and the book says to add the network loop of the TMDI

"If I had known it would turn out like this, I would have became a locksmith" Albert Einstein

NCSS NCTS NCTE CS1000E
Mitel 3300 4.2 basic & advanced, 5000 4.0, NuPoint I&M 4.2
 
Print out your CEQU and post it.
What DLOP are you trying to input?
What error are you getting?
 
Here's the CEQU:

REQ prt
TYPE cequ

CEQU
MPED 8D
TERM
REMO
TERD
REMD
TERQ
REMQ
SUPL V000 V004 V008 N140
V252
SUPC
SUPF
XCT
CONF
MGTDS IPMG IPMG_TYPE
044 004 0 MGC
046 004 0 MGC
124 000 0 MGC
126 000 0 MGC
128 008 0 MGC
130 008 0 MGC
MGCONF IPMG PORTS IPMG_TYPE
045 004 0 30 MGC
047 004 0 30 MGC
125 000 0 30 MGC
127 000 0 30 MGC
129 008 0 30 MGC
131 008 0 30 MGC
MFSD * 044 * 046 * 124 * 126
* 128 * 130

DLOP NUM DCH FRM TMDI LCMT YALM T1TE TRSH MG_CARD
PRI 021 23 ESF YES B8S FDL 0 00 000 0 03
022 23 ESF YES B8S FDL 0 00 008 0 03
DTI2 MG_CARD
MISP MG_CARD
EXT0 3PE
EXT1 3PE
MCFN 011 MB

Building it in LD 17, at the end is DTIC and I cannot cr past it. Whenever I enter a number I receive this sorry charlie code:

SCH2022
Cannot delete a non-DTI loop or add a DTI loop which is not undefined,
or make changes to a non-DTI loop.

Jim




"If I had known it would turn out like this, I would have became a locksmith" Albert Einstein

NCSS NCTS NCTE CS1000E
Mitel 3300 4.2 basic & advanced, 5000 4.0, NuPoint I&M 4.2
 
You don't need to put anything in at the DTIC prompt, just return buy it.
 
For example at the dlop you would enter

4 24 esf

Your loop number is set in my example as 4
 
Thanks for the posts. I finally got hold of a coworker in PA who explained that DTIC is a holdover from the SL1 days and not used. What was happening was I would receive a shwartz code and then it would give me the DLOP prompt again. He said to simply cr through those and it would complete...and it did...I wasn't going far enough.

Thanks, Jim

"If I had known it would turn out like this, I would have became a locksmith" Albert Einstein

NCSS NCTS NCTE CS1000E
Mitel 3300 4.2 basic & advanced, 5000 4.0, NuPoint I&M 4.2
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top