Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

isdn bri configuration

Status
Not open for further replies.

ducatisenna

IS-IT--Management
Dec 6, 2006
55
TR
hi

i want to set quad bri trunk on avaya 406
i have 2 isdn output with RJ45 with 2 wire cables

i put one 2 wire cable in nt1 unit, and i connect the nt1's isdn output(4 wire) to the avaya's quad bri port,

but when i dial outside it says disconnect,
and incoming calls always busy,

is there a way to configure isdn bri in this system.
avaya 406 version 3.2.55
i want to raise 4.0

is there a pdf about this subject
please help me

serhan from cablenet
 
If you have installed the BRI card in the IPO and connect the wiring properly then it should work.
If you redefined the default incoming and outgoing line IDs then you will have to program the appropriate Incoming Call Route and Shortcodes for outgoing calling on these line IDs.

Run Monitor, enable all of ISDN as a filter and disconnect/re-connect the BRi, you should get some events back showing that the connection is OK.
Ring in on the line and then you should see the incoming call etc.
 
you say a rj45 in to the nt1 (the 2 wire)
this should be rj11 and is out in on the left side
the rj45 (4 wire) can be a normal patchcable
the bri card is autosense,you don't need to cross wires
like intrigrant says in default it should work
maybe change your incoming call route
just the line id and the destination filled in
this should work
monitor gives you information like intrigrant also said
even if the isdn is not working right is should give you info


______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!
 
It,s an rj11 in Holland;)

But seen strange things in other countries.

Rj45,coax,enz

Just make sure the output is an standerd cat5/cat5e cable then it will work out of the box.


Greets Peter
 
are the bri trunk lights green ?
my bri lines arent green, they are unresponsive,
i think my problem is about lines, not ipo configs.
should i try 4 wire cable or just utp cable is enough.

 
An utp cable is enough and the light don,t have to be always green.
But it must be green if you make a call, because if its synct then it,s green.

Greets Peter
 
hey i live in brabant
everything above the rivers is for me not in holland :)

______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!
 
Brabant hahahahahahaha
Je kan altijd nog verhuizen!!!


Groetjes Peter
 
alles is beter dan dordrecht :)
turkije is het wel beter weer hmmmmm


______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!
 
Hallo, we hebben wel zwolle naar huis gestuurd!!!!!!!!

Groetjes Peter
 
kom jij ook al uit dort ?


______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!
 
Nee, ik zit in een veel mooiere dorpje naast dordt (Alblasserdam).
Maar hoop wel dat Dordt promoveerd, maar we houden geen spitsen over!!!
Tevens oud collega van Cor 11 jaar geleden (phoe wat gaat de tijd hard........)

Groetjes Peter
 
je word oud, maar zover woon ik dus niet bij jullie vandaan
het is net aan brabant,in een kwartiertje zit ik in dort

______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!
 
Dordt schrijf je met dt en is wel mooi de oudste stad van holland en de op twee na grootste van ZH, as je't maar weet.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top