ipLDK-60 ip phones installation guide

[Donsam]

How do i get my ip phones working on this system. i cant seem to get it to work no matter what i do. In desperate need of help.

thanks

 

[doktor]

You can use this one: thread1613-1484637
The command structure of the ipLDK-60 is similiar to ipLDK-100.

///doktor

 

[Donsam]

Do i need the VOIU board for the ip phones to work?

 

[doktor]

Hi Donsam

No, you do only need the VOIB:
The VOIB board can be installed on the basic MBU. It
provides the Ethernet interface for S/W applications and VoIP features, like IP trunk and IP phones.
There exists an optional VoIP daughter board.(VOIU)

Maximum Capacity: 8 channels
-VOIB provides four(4) VoIP channels.
-VOIU provides four(4) VoIP channels.

If you use softphones, then a license per user is needed.

///doktor

 

[Donsam]

ok but the phone still don't work. I did everything that that was said in the guide but the phone still shows

( Local - No ACK)
( Set[*]- Restart[#]

what am i not doing?

thanks doc

 

[morenot]

Do you setting the ip phone?
The ip phone also must be configurated..

 

[morenot]

On the ip phone:

1. Press ‘*’.
2. Press ‘#’ to change to ‘Remote’; press Volume?.
3. Set the IP address according to table 1 (dot = *); press [Hold/Save]
button; press Volume?.
4. Set Subnet Mask (dot = *); press [Hold/Save] button; press Volume?.
5. Set Gateway address (dot = *); press [Hold/Save] button; press
Volume?.
6. Set the VOIB IP address according to table 1 (dot = *); press
[Hold/Save] button.

 

[morenot]

Table 1 was an example, dont´t care
Set the IP address for you ip phone
Set Subnet mask
Set Gateway address
Set VOIB IP address

 

[Donsam]

i did all those already. any other options i need to configure?

 

[doktor]

Here is my "way" install an IP phone:
(In this example the LIP-24 IP Phone is used, but this wil work with any other LG-Nortel IP phone):
----------------------------------------------------

LIP-24 is connected to a WAN IP address.

LIP-24 will write the following in the display when the power is connected:

NO RESPONSE FROM MFIM [L]
SET [*] - Retry [#]

Key *
MODE setting.
Put LIP-24 REMOTE
Enter the volume down arrow.

The following addresses and parameters shown in the accompanying agreement papers.

PHONE IP ADDRESS (DOT: *)
Enter here the IP address of LIP-24. Use the asterisk (*) as a point to be used within the numbers in the IP address.
IP address must be entered manually, because it can not be assigned through DHCP.
Remember to press SAVE after each input.
Enter the volume down arrow.

PHONE NET MASK (DOT: *)
Here, enter the subnet mask for LIP-24. Use the asterisk (*) as a point to be used within the numbers in the IP address.
Subnet mask must be entered manually, because it can not be assigned through DHCP.
Remember to press the SAVE button after each input.
Enter the volume down arrow.

ROUTER IP ADDRESS (DOT: *).
Here, enter the default gateway for the LIP-24. Use the asterisk (*) as a point to be used within the numbers in the IP address.
Subnet mask must be entered manually, because it can not be assigned through DHCP.
Remember to press the SAVE button after each input.
Enter the volume down arrow.

LIP-24 then ask about:
SAME WITH MFIM LAN?
Set this to NO. Default is to YES.
Remember to press the SAVE button after typing in each entry. Enter the volume down arrow.

MFIM IP ADDRESS (DOT: *)
Here enter the IP address for the ipLDK-60 (VOIB) must be entered.
Use the asterisk (*) as a point to be used within the numbers in the IP address.
Subnet mask must be entered manually, because it can not be assigned through DHCP.
Remember to press the SAVE button after each input.
Enter the volume down arrow.

There are additional items that can be set as needed:
INPUT DEVICE NUMBER
DHCP (Disabled) (not used in appliances in the LOCAL mode).

VLAN CONFIGURATION (If telephony data to travel in separate VLAN specified number here. VLAN number is entered, according to data in agreement papers).

WEB PASSWORD this is not optional.

Then restart the LIP phone.

If registraion fails, you might have forgotten to enter the MAC address of the IP Phone in PGM286.


///doktor

 

[Donsam]

Thanks everyone got it working. but how do i allow ip sets to call the digital ones... they cant call each other ip sets say CHANNEL UNAVAILABLE and digital sets sat BUSY.

 

[doktor]

Please check the settings described in:
thread1613-1484637: How to program an IP phone in ipLDK-100!!

///doktor