Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations SkipVought on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

ipconfig /all 1

Status
Not open for further replies.

pechenegs

MIS
Jun 15, 2003
1,040
0
0
GB
Hi all, when I go to the cmd prompt in run, and type in ipconfig /all, it flashes for a second and then it disappears.

Does anyone know how to rectify this?

Cheers

Pech

Member of ASAP Alliance of Security Analysis Professionals

under the name khazars
 
oops, I have windows 7!

Member of ASAP Alliance of Security Analysis Professionals

under the name khazars
 
Are you sure you're doing it at a CMD prompt. If you run it from W7 search bar, it will flash for a second. If you type CMD in the search bar, then right click (run as administrator) on CMD, I don't see any reason why it shouldn't behave normally.

"Living tomorrow is everyone's sorrow.
Modern man's daydreams have turned into nightmares.
 
pechenegs said:
it flashes for a second and then it disappears.
Because that is what ALL command line calls do when invoked from the Run... dialogue.

The command runs, then closes if it doesn't need to wait for input.

Chris.

Indifference will be the downfall of mankind, but who cares?
Time flies like an arrow, however, fruit flies like a banana.
Webmaster Forum
 
Well, the OP didn't say how they were running the command but it SOUNDS like they were doing from the RUN or SEARCH box. I guess we have to wait for them to confirm.................

"Living tomorrow is everyone's sorrow.
Modern man's daydreams have turned into nightmares.
 
Hi guys, I'm running it from run!

Member of ASAP Alliance of Security Analysis Professionals

under the name khazars
 
cheers Goom, that worked! Star for ya!

Member of ASAP Alliance of Security Analysis Professionals

under the name khazars
 
but, running it from run, it just flashes for a second then disappears!

Member of ASAP Alliance of Security Analysis Professionals

under the name khazars
 
Are you opening a command prompt window with Start -> Run... -> cmd <return> THEN typing the command line in that window?

Chris.

Indifference will be the downfall of mankind, but who cares?
Time flies like an arrow, however, fruit flies like a banana.
Webmaster Forum
 
No chris, I'm clicking start/Run, then typing in ipconfig /all!

Member of ASAP Alliance of Security Analysis Professionals

under the name khazars
 
That is why it is closing as soon as the command completes.

Chris.

Indifference will be the downfall of mankind, but who cares?
Time flies like an arrow, however, fruit flies like a banana.
Webmaster Forum
 
You realize (ChrisHirst) that you have been about three steps behind in this thread the whole way.

"Living tomorrow is everyone's sorrow.
Modern man's daydreams have turned into nightmares.
 
I don't think so.

Post ONE. said:
Hi all, when I go to the cmd prompt in run, and type in ipconfig /all, it flashes for a second and then it disappears.

My FIRST post
chrishirst said:
Because that is what ALL command line calls do when invoked from the Run... dialogue.

The command runs, then closes if it doesn't need to wait for input.

A few posts later on
pechenegs said:
No chris, I'm clicking start/Run, then typing in ipconfig /all!

My first post in this thread says EXACTLY what you are doing and WHY you see what you do!

Chris.

Indifference will be the downfall of mankind, but who cares?
Time flies like an arrow, however, fruit flies like a banana.
Webmaster Forum
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top