IP Trunks Help Required

[Gigaic]

I set up IP trunks (MC32) on option 11c to link to two BCM50s (the BCM50s are already connected). When I try to dial, this is what I get (44 is LSC on option 11C, 55 and 66 are DSCs to BCM50s):
*******************************************************************
VDCH 11 OMSG SETUP REF 00000190 CH 5 0 0 15 TOD 16:19:20
FEAT :NCID
PROGRESS: ORIG ADDR IS NOT ISDN
CALLING #:1090 NUM PLAN: PRIVATE/ABBREVIATED (CDP)
CALLED #:662225 NUM PLAN: PRIVATE/ABBREVIATED (CDP)
DCH 11 IMSG CALLPROC REF 00000190 CH 5 0 0 15 TOD 16:19:20
DCH 11 IMSG DISC REF 00000190 CH 5 0 0 15 TOD 16:19:20
CAUSE :SWED EQIP CONGESTION
DCH 11 OMSG RELEASE REF 00000190 CH 5 0 0 15 TOD 16:19:20
DCH 11 IMSG REL COMP REF 00000190 CH 5 0 0 15 TOD 16:19:20
DCH 11 OMSG SETUP REF 00000190 CH 5 0 0 15 TOD 16:19:34
FEAT :NCID
PROGRESS: ORIG ADDR IS NOT ISDN
CALLING #:1090 NUM PLAN: PRIVATE/ABBREVIATED (CDP)
CALLED #:552222 NUM PLAN: PRIVATE/ABBREVIATED (CDP)
DCH 11 IMSG CALLPROC REF 00000190 CH 5 0 0 15 TOD 16:19:34
DCH 11 IMSG DISC REF 00000190 CH 5 0 0 15 TOD 16:19:34
CAUSE :SWED EQIP CONGESTION
DCH 11 OMSG RELEASE REF 00000190 CH 5 0 0 15 TOD 16:19:34
DCH 11 IMSG REL COMP REF 00000190 CH 5 0 0 15 TOD 16:19:34
******************************************************************
I am not sure if my CDP is alright. Post below:

>ld 87
ESN000
MEM AVAIL: (U/P): 2659305 USED U P: 263174 124944 TOT: 3047423
DISK RECS AVAIL: 384
REQ prt
CUST 0
FEAT cdp
TYPE all
LSC 44
DEL 2
DSC 55
FLEN 6
DSP LSC
RRPA NO
RLI 1
NPA
NXX
DSC 66
FLEN 6
DSP LSC
RRPA NO
RLI 1
NPA
NXX

BCM 50 extensions are 2221 to 2225.

Please help.

Thanks. GEORGE

 

[biv343]

If you run the BCM monitor app, what do you see for incoming digits on the BCM on the line monitor? Also, the UIP tab on BCM monitor should give you a good idea of what is happening on that end from an IP/MCDN perspective.

Do you have the target lines built on the BCMs to receive the appropriate digits, and have the lines assigned to the sets? You'd need to build your target lines to receive 55+ext and 66+ext respectively. If you don't have the MCDN keycode in the BCM, assign those received digits in the 'public' field in the target line. If you have MCDN you can assign them in the
private' field.

Can you call from the BCM to the M1 OK?

 

[Engine1]

Are these calls NRS routed?

 

[Gigaic]

These calls are not NRS routed. There is no signalling server in the configuration. Just using an MC32 for IP trunks.

BIV343, I cannot call from the BCM to the M1. 44 is M1 code, 55 is BCM1 code and 66 is BCM2 code. Under destination digits (Resources/Telephony Resources/Internal IP Trunks/ Remote Gateways) on the BCMs, for BCM1 we have destination digits set for 55 222 (plus IP address of BCM2). If I try to enter details for M1 (55 222 plus IP address of M1) it gets rejected with error "digits overlap". Digits dialed from M1 to reach BCM1 numbers are also in the range 55 2221 - 55 2225. How can I put in an entry for the M1? I will check the monitor when I get to the BCM site and let you know.

Thanks for your help.
George

 

[Gigaic]

BCMs are able to call M1 alright at all times, however M1 is only able to call BCMs immediatelly after MC32 reset. A short while after reset no calls are possible from the M1 to the BCMs. Here is DCH info for a successful and failed call:

Successful Call
****************
DCH 11 OMSG SETUP REF 00000190 CH 5 0 0 15 TOD 11:15:02
FEAT :NCID
PROGRESS: ORIG ADDR IS NOT ISDN
CALLING #:1090 NUM PLAN: PRIVATE/ABBREVIATED (CDP)
CALLED #:552221 NUM PLAN: PRIVATE/ABBREVIATED (CDP)

DCH 11 IMSG CALLPROC REF 00000190 CH 5 0 0 15 TOD 11:15:02

DCH 11 IMSG ALERT REF 00000190 CH 5 0 0 15 TOD 11:15:02

DCH 11 IMSG CONNECT REF 00000190 CH 5 0 0 15 TOD 11:15:06

DCH 11 OMSG CONN ACK REF 00000190 CH 5 0 0 15 TOD 11:15:06

DCH 11 OMSG DISC REF 00000190 CH 5 0 0 15 TOD 11:16:00
CAUSE :NORMAL CALL CLEARING

DCH 11 IMSG RELEASE REF 00000190 CH 5 0 0 15 TOD 11:16:00
CAUSE :NORMAL CALL CLEARING

DCH 11 OMSG REL COMP REF 00000190 CH 5 0 0 15 TOD 11:16:00
************************************************************


Failed Call
************
DCH 11 IMSG CALLPROC REF 00000190 CH 5 0 0 15 TOD 11:18:48

DCH 11 IMSG DISC REF 00000190 CH 5 0 0 15 TOD 11:18:48
CAUSE :SWED EQIP CONGESTION

DCH 11 OMSG RELEASE REF 00000190 CH 5 0 0 15 TOD 11:18:48

DCH 11 IMSG REL COMP REF 00000190 CH 5 0 0 15 TOD 11:18:48
***********************************************************


Here is activity info in the MC32 (Telnet session):
***************************************************
ITG> routeShow

ROUTE NET TABLE
destination gateway flags Refcnt Use Interface
----------------------------------------------------------------------------
0.0.0.0 10.1.2.250 3 1 525 ixpMac0
10.1.0.0 10.1.2.177 101 0 0 ixpMac0
192.168.1.0 192.168.1.177 101 0 0 ixpMac1
10.1.0.0 10.1.2.177 101 0 0 ixpMac0
----------------------------------------------------------------------------

ROUTE HOST TABLE
destination gateway flags Refcnt Use Interface
----------------------------------------------------------------------------
127.0.0.1 127.0.0.1 5 0 0 lo0
----------------------------------------------------------------------------
value = 77 = 0x4d = 'M'
ITG> 2000 10 1 02:52:44 (MSM) :ITG0203 Node IP: 10.7.1.15
Codec: G711Alaw
Tx: 0.00 500093ms Poor Rx: 100.00 9ms Poor
Codec: G711Ulaw
Tx: 0.00 500093ms Poor Rx: 100.00 9ms Poor
Codec: G729A
Tx: 0.00 500093ms Poor Rx: 100.00 9ms Poor
Codec: G729AB
Tx: 0.00 500093ms Poor Rx: 100.00 9ms Poor

2000 10 1 02:52:44 (MSM) :ITG0203 Node IP: 10.3.1.15
Codec: G711Alaw
Tx: 0.00 500093ms Poor Rx: 100.00 5ms Poor
Codec: G711Ulaw
Tx: 0.00 500093ms Poor Rx: 100.00 5ms Poor
Codec: G729A
Tx: 0.00 500093ms Poor Rx: 100.00 5ms Poor
Codec: G729AB
Tx: 0.00 500093ms Poor Rx: 100.00 5ms Poor

2000 10 1 03:02:45 (SNMP) SP str is R8.01
2000 10 1 03:02:45 (SNMP) SP str is R8.01
2000 10 1 03:02:45 (SNMP) SP str is R8.01
2000 10 1 03:02:45 (SNMP) SP str is R8.01
2000 10 1 03:02:45 (SNMP) SP str is R8.01
2000 10 1 03:02:45 (SNMP) SP str is R8.01
2000 10 1 03:02:45 (SNMP) SP str is R8.01
2000 10 1 03:02:45 (SNMP) SP str is R8.01
2000 10 1 03:04:16 (A07) :Board Disabled - LED ON
2000 10 1 03:04:41 (SNMP) :services_set: Setting file Lock
2000 10 1 03:04:41 (NMM) :Module 2 setting file system lock
2000 10 1 03:04:41 (NMM) :itgFileXfer: transfer type: TYPE I
2000 10 1 03:04:41 (NMM) :itgFileXfer returning with status OK
2000 10 1 03:04:41 (NMM) :fileSize: 236
2000 10 1 03:04:41 (NMM) :hostFileGet exiting with status OK
2000 10 1 03:04:41 (NMM) :sending fileXferOk message to task 2
2000 10 1 03:04:41 (NMM) :hostFileGet returning with status 0
2000 10 1 03:04:41 (NMM) :NMM received file data OK message from RMM
2000 10 1 03:04:41 (SNMP) :services_set: Clear file Lock
2000 10 1 03:04:41 (SNMP) :services_set: Setting file Lock
2000 10 1 03:04:41 (NMM) :Module 4 setting file system lock
2000 10 1 03:04:41 (NMM) :itgFileXfer: transfer type: TYPE I
2000 10 1 03:04:41 (NMM) :itgFileXfer returning with status OK
2000 10 1 03:04:41 (NMM) :fileSize: 877
IP Address from NVRAM: 192.168.1.177
2000 10 1 03:04:41 (NMM) :hostFileGet exiting with status OK
2000 10 1 03:04:41 (NMM) :sending fileXferOk message to task 4
2000 10 1 03:04:41 (NMM) :hostFileGet returning with status 0
2000 10 1 03:04:41 (SNMP) :ContactSet: The SNMP Value is Invalid
2000 10 1 03:04:42 (NMM) :NMM received file data OK message from MAM
2000 10 1 03:04:42 (SNMP) :services_set: Clear file Lock
2000 10 1 03:04:42 (SNMP) :services_set: Setting file Lock
2000 10 1 03:04:42 (NMM) :Module 14 setting file system lock
2000 10 1 03:04:42 (NMM) :itgFileXfer: transfer type: TYPE I
2000 10 1 03:04:42 (NMM) :itgFileXfer returning with status OK
2000 10 1 03:04:42 (NMM) :fileSize: 174
2000 10 1 03:04:42 (NMM) :hostFileGet exiting with status OK
2000 10 1 03:04:42 (NMM) :sending fileXferOk message to task 14
2000 10 1 03:04:42 (NMM) :hostFileGet returning with status 0
2000 10 1 03:04:42 (NMM) :NMM received file data OK message from ATPM

Download codec image completed -DSP# 0, Image Id = 0
Download codec image completed -DSP# 1, Image Id = 02000 10 1 03:04:43 (SNMP) :s
ervices_set: Clear file Lock

Download codec image completed -DSP# 2, Image Id = 0
Download codec image completed -DSP# 3, Image Id = 0
Download codec image completed -DSP# 4, Image Id = 0
Download codec image completed -DSP# 5, Image Id = 0
Download codec image completed -DSP# 6, Image Id = 0
Download codec image completed -DSP# 7, Image Id = 02000 10 1 03:04:46 (NPM) :RA
DVision H.323 payload update complete.
2000 10 1 03:04:46 (COM) :Current ESN5 Prefix is set to |100|


Can anyone help me interpret this.

Thanks
George