Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Intuity Audix Mode Codes
- Thread starter agpham
- Start date
The mode codes are whatever u have in the system connected to it. They have to agree in the telephone system and the audix to work properly.
Da-vi'do
P.S. For the best response to a question, read FAQ222-2244. Also give the type & version of your voice mail & pbx & preview your post to make sure it is complete & understandable. Please answer all questions so that I may have the info to assist you. Leaving a post on how you fixed the problem will also be appreciated.
Da-vi'do
P.S. For the best response to a question, read FAQ222-2244. Also give the type & version of your voice mail & pbx & preview your post to make sure it is complete & understandable. Please answer all questions so that I may have the info to assist you. Leaving a post on how you fixed the problem will also be appreciated.
- Thread starter
- #3
odes Sent FROM the Phone system
#00#EEE## Intercom from extension EEE (used to log in)
#01#LLL## Incoming call from CO line number LLL.
#02#FFF#EEE# Unanswered Intercom call From extention FFF to extention EEE
#03##EEE# Unanwsered Outside call At ext EEE
#10### Night Service Off
#11### Night Service On
Codes sent FROM the voice mail system
#53EEE Message light ON EEE = Extention
#*53EEE Message light Off EEE = Extention
I'm not sure if these actually get used but they are in my notes so here they are
other codes sent FROM the phone system
#06### test code sent to the voicemail after a powerfail to see if ports are connected.
#07### test code sent to the voicemail via a different port every 30 minutes to see if the ports are still connected.
#08##PPP# re-activation code sent to the Voicemail to report that port PPP has been tested and found restored after a previous disconnect.
This Link might help
~Don~
#00#EEE## Intercom from extension EEE (used to log in)
#01#LLL## Incoming call from CO line number LLL.
#02#FFF#EEE# Unanswered Intercom call From extention FFF to extention EEE
#03##EEE# Unanwsered Outside call At ext EEE
#10### Night Service Off
#11### Night Service On
Codes sent FROM the voice mail system
#53EEE Message light ON EEE = Extention
#*53EEE Message light Off EEE = Extention
I'm not sure if these actually get used but they are in my notes so here they are
other codes sent FROM the phone system
#06### test code sent to the voicemail after a powerfail to see if ports are connected.
#07### test code sent to the voicemail via a different port every 30 minutes to see if the ports are still connected.
#08##PPP# re-activation code sent to the Voicemail to report that port PPP has been tested and found restored after a previous disconnect.
This Link might help
~Don~
There are books at support.avaya.com that address how to integrate particular pbx es with the Intuity. Use google advanced to look for the book. Some pbx es can be integrated using digital terminal emulation that usually works better than mode codes. The particular pbx determines what can be used as mode codes. The dial plan usually determines that. The Intuity also must have the modes codes integration loaded on it if u go the 'mode codes' direction.
What kind of pbx do u have?
What kind of pbx do u have?
- Thread starter
- #6
I'm trying to integrate this to an Asterisk VOIP PBX softswitch. There are means and flexibility to customize outpulse digits and such. People appear to be more emotionally attached to their voicemail system than their telephone set. Thanks for the info.
---
Andy Pham, ACS/FS-IT
Honeywell International, Inc.
andy.pham@honeywell.com
---
Andy Pham, ACS/FS-IT
Honeywell International, Inc.
andy.pham@honeywell.com
Switch Interface Administration
Call Data Interface Administration
MWI Administration
Device Assignment
is where the mode codes are listed in the INtuity if the INtuity already has the mode code integration loaded. If it is not loaded, then u have to get the appropriate disk or tape and load it.
Call Data Interface Administration
MWI Administration
Device Assignment
is where the mode codes are listed in the INtuity if the INtuity already has the mode code integration loaded. If it is not loaded, then u have to get the appropriate disk or tape and load it.
- Status
Similar threads
- Locked
- Question
- Locked
- Question
- Locked
- Question
- Locked
- Question