I was wondering if someone can help. The issue I have is that I have 3 sites Sydney Main site NR1, Melbourne NR 2 and New Zealand NR 8.
When somebody calls from New Zealand (NR 8) to Melbourne (NR 2) they have been configured to call via Sydney (Main Site NR 1). I have set this up using intervening regions i.e. NR8 to call NR 2 has to go via NR1. This works up until the point the call connects then the call goes from NR 8 to NR 2. Please see below. The site uses a Hub and Spoke Technology as opposed to Mesh.
The example below shows a user in New Zealand calling a Melbourne Number and as you can see the call starts off using Sydney, however, the call then binds between NR 8 and NR 2, bypassing NR 1.
list trace previous Page 1
LIST TRACE
time data
10:23:43 active station 5095 cid 0x938
10:23:43 G729A ss
ff ps:20
rgn:8 [10.100.64.95]:2096
rgn:1 [10.2.1.49]:2060
10:23:43 dial 00396850 route:ARS
10:23:43 term trunk-group 20 cid 0x938
10:23:43 dial 00396850222 route:ARS
10:23:43 route-pattern 21 preference 1 cid 0x938
10:23:43 seize trunk-group 20 member 8 cid 0x938
10:23:43 Setup digits 0396850222
10:23:43 Calling Number & Name 5095 Robert-Cotter
10:23:43 G729A ssff ps:20
rgn:8 [10.100.64.95]:2096
rgn:2 [10.2.31.6]:2080
10:23:43 Proceed trunk-group 20 member 8 cid 0x938
10:23:45 active trunk-group 20 member 8 cid 0x938
VOIP data from: [10.2.31.6]:2080
10:23:54 Jitter:0 0 0 0 0 0 0 0 0 0: Buff:11 WC:0 Avg:0
10:23:54 Pkloss:0 0 0 0 0 0 0 0 0 0: Oofo:0 WC:0 Avg:0
10:23:57 idle station 5095 cid 0x938
10:29:55 TRACE COMPLETE station 5095 cid 0x0
display ip-network-region 8 Page 3 of 19
Source Region: 8 Inter Network Region Connection Management I M
G A t
dst codec direct WAN-BW-limits Video Intervening Dyn A G c
rgn set WAN Units Total Norm Prio Shr Regions CAC R L e
1 3 y Calls 3 n t
2 3 n 1: : : n t
3
4
5
6
7
8 1 all
9
10
Anybody know how I can ensure calls when connected go through Sydney and not directly between sites.
Regards
Naz
When somebody calls from New Zealand (NR 8) to Melbourne (NR 2) they have been configured to call via Sydney (Main Site NR 1). I have set this up using intervening regions i.e. NR8 to call NR 2 has to go via NR1. This works up until the point the call connects then the call goes from NR 8 to NR 2. Please see below. The site uses a Hub and Spoke Technology as opposed to Mesh.
The example below shows a user in New Zealand calling a Melbourne Number and as you can see the call starts off using Sydney, however, the call then binds between NR 8 and NR 2, bypassing NR 1.
list trace previous Page 1
LIST TRACE
time data
10:23:43 active station 5095 cid 0x938
10:23:43 G729A ss
ff ps:20rgn:8 [10.100.64.95]:2096
rgn:1 [10.2.1.49]:2060
10:23:43 dial 00396850 route:ARS
10:23:43 term trunk-group 20 cid 0x938
10:23:43 dial 00396850222 route:ARS
10:23:43 route-pattern 21 preference 1 cid 0x938
10:23:43 seize trunk-group 20 member 8 cid 0x938
10:23:43 Setup digits 0396850222
10:23:43 Calling Number & Name 5095 Robert-Cotter
10:23:43 G729A ss
ff ps:20rgn:8 [10.100.64.95]:2096
rgn:2 [10.2.31.6]:2080
10:23:43 Proceed trunk-group 20 member 8 cid 0x938
10:23:45 active trunk-group 20 member 8 cid 0x938
VOIP data from: [10.2.31.6]:2080
10:23:54 Jitter:0 0 0 0 0 0 0 0 0 0: Buff:11 WC:0 Avg:0
10:23:54 Pkloss:0 0 0 0 0 0 0 0 0 0: Oofo:0 WC:0 Avg:0
10:23:57 idle station 5095 cid 0x938
10:29:55 TRACE COMPLETE station 5095 cid 0x0
display ip-network-region 8 Page 3 of 19
Source Region: 8 Inter Network Region Connection Management I M
G A t
dst codec direct WAN-BW-limits Video Intervening Dyn A G c
rgn set WAN Units Total Norm Prio Shr Regions CAC R L e
1 3 y Calls 3 n t
2 3 n 1: : : n t
3
4
5
6
7
8 1 all
9
10
Anybody know how I can ensure calls when connected go through Sydney and not directly between sites.
Regards
Naz