Internal Calls fail to call PRI/ISDN route 1

[shelton2]

At this time it appears that all internal calls that originate internally and are dialing x7799 receive dialtone, dial one more digit (any number) and the call is completed to the PRI/ISDN route. All external calls via the PSTN or across a tie route to x7799 appear to be working just fine. After creating an internal call to the x7799 with a call trace, the PBX has a main progress mark that states that one or more digits have been dialed and the system requires more digits. The PRI/ISDN call route has an acod of 20228 and we are using 7799 with ACD and ncfw to 20228.
Any thoughts, ideas or has anyone seen this problem???
.trac 0 8524

ACTIVE TN 144 0 02 10 V PHYSICAL TN 000
ORIG 144 0 02 10 V PHYSICAL TN 000 0 SCR MARP 0 8524 I2004
TERM NONE
TDTN 64 SLOT 0 1 PTY SLOT 0 1
DIAL DN 20228
MAIN_PM DIAL AUX_PM
TALKSLOT NONE
QUEU 128
CALL ID 230 8716

-----------------------------------------------------------
-----------------------------------------------------------

.trac 0 8524

ACTIVE TN 144 0 02 10 V PHYSICAL TN 024 0 15 05
ORIG 144 0 02 10 V PHYSICAL TN 000 0 SCR MARP 0 8524 I2004
TERM 008 23 TIE RMBR 28 23
DIAL DN 202289
MAIN_PM ESTD
TALKSLOT ORIG 39 TERM 7 JUNCTOR ORIG0 TERM0
QUEU NONE
CALL ID 230 8716


---- ISDN PRA CALL (TERM) ----
CALL REF # = 23
BEARER CAP = VOICE
HLC =
CALL STATE = 10 ACTIVE
CALLING NO = 8524 NUM_PLAN:E163 TON:NATIONAL ESN:UNKNOWN
CALLED NO = 9 NUM_PLAN:E163 TON:NATIONAL ESN:UNKNOWN
PDCA 1 PAD 0 6 PCML MU MU

 

[johnpoole]

7799 with ACD and ncfw to 20228.


make 7799 a dsc, that maxp 1 acd is translating 7799 to the acod but a ncfw acd does not pass the original dialed dn to the tie..

out the acd
the go to 86 and add a rlb

REQ  prt

CUST 0

FEAT rlb

RLI  13


RLI  13
ENTR 0
LTER NO
ROUT 100
TOD  0 ON  1 ON  2 ON  3 ON
     4 ON  5 ON  6 ON  7 ON
VNS  NO
CNV  NO
EXP  NO
FRL  0
DMI  0
FCI  0
FSNI 0
SBOC NRR
IDBB DBA
IOHQ NO
OHQ  NO
CBQ  NO

frl 0 give any ncos access, the route would be the same one your using now with acod 20228.,. then go to 87 and add one more line

REQ  new
CUST 0
FEAT cdp
TYPE dsc
DSC  7799
FLEN 4
DSP
RLI  13
NPA
NXX
DSC

that sends the digits to the correct route, not i need to remove that before some tries to call me...

john poole
bellsouth business
columbia,sc

 

[shelton2]

I am receiving an esn0126 error, the CDP data block(cdp-list) does not exist.

 

[shelton2]

John I was able to enable cdp in ld 86 and everything else worked out just as you explained. Thanks again.