Interconnect hipath 4000 and omnipcx entreprise

[illios]

We have a hipath 4000 V1 with a DUIN2
Board we want trunking with alcatel omnipcx entreprise T2 interface
Witch protocol must be used and help me Who config diun2 card step by step
Thanks

 

[thepfy]

These may help

http://www.alcatelunleashed.com/viewtopic.php?t=20666

https://www.tek-tips.com/viewthread.cfm?qid=1807525

https://www.tek-tips.com/viewthread.cfm?qid=1791767

https://www.alcatelunleashed.com/viewtopic.php?t=14635

https://www.alcatelunleashed.com/viewtopic.php?t=5103

 

[illios]

this is the config of diun2 what we done

ADD-BCSUIU,1,1,25,"Q2196-X ",0,,,,,1,,,,,A;


DISPLAY-COT:COTNO=120;
H500: AMO COT STARTED

COT: 120 INFO: COT FOR E1
DEVICE: INDEP SOURCE: DB
PARAMETER:
RECALL IF USER HANGS UP IN CONSULTATION CALL RCL
TRUNK CALL TRANSFER XFER
TRUNK SIGNALING ANSWER ANS
CALL EXTEND FOR BUSY, RING OR CALL STATE CEBC
TIE LINES TIE
NETWORKWIDE AUTOMATIC CALLBACK ON BUSY CBBN
NETWORKWIDE AUTOMATIC CALLBACK ON FREE CBFN
END-OF-DIAL FOR BLOCK IS SET BLOC
SEND NO NODE NUMBER TO PARTNER LWNC
INCOMING CIRCUIT FROM SYSTEM WITHOUT LCR NLCR
TSC-SIGNALING FOR NETWORKWIDE FEATURES (MANDATORY) TSCS
USE DEFAULT NODE NUMBER OF LINE DFNN
CALL FORWARDING VALIDATION PROCEDURES POSSIBLE CFVA
NO TONE NTON

AMO-COT -111 CLASS OF TRUNK FOR CALL PROCESSING
DISPLAY COMPLETED;

DISPLAY-COP:COPNO=120;
H500: AMO COP STARTED

COP: 120 INFO: COP FOR E1
DEVICE: INDEP SOURCE: DB
PARAMETER:
REGISTRATION OF LAYER 3 ADVISORIES L3AR

AMO-COP -111 CLASS OF PARAMETER FOR DEVICE HANDLER
DISPLAY COMPLETED;
<


DISPLAY-COSSU:TYPE=COS,COS=120;
H500: AMO COSSU STARTED
+------+-----------------+---------------+-----------------+
| COS | VOICE | FAX | DTE |
+------+-----------------+---------------+-----------------+
| 120 |>COS FOR E1 |
| | TA | NOCO | TA |
| | TNOTCR | NOTIE | TNOTCR |
| | CDRC | | |
| | MB | | |
| | COSXCD | | |
| | VCE | | |
| | SPKR | | |
| | FWDNWK | | |
| | OVCAT | | |
| | FWDECA | | |
| | FWDDIR | | |
| | CFB | | |
| | CFNR | | |
| | CFSWF | | |
| | CW | | |
| | FWDEXT | | |
| | TTT | | |
| | | | |
+------+-----------------+---------------+-----------------+
AMO-COSSU-111 CLASSES OF SERVICE
DISPLAY COMPLETED;


DISPLAY-BUEND:TGRP=120;
H500: AMO BUEND STARTED

+------------------------------- FORMAT = L -----------------------------------+
| TGRP NUMBER : 120 TGRP NAME : OSO NETWORK MAXIMUM NO. : 30 |
| CHARCON : NEUTRAL |
| SUBGROUP NO.: 18 DEVICE TYPE : S2CONN TRACENO : 0 |
| RESERVED : N SEARCH MODE : CIRCULAR ACD THRESHOLD : * |
| NUMBER OF ASSOCIATED ROUTES : 1 PRIORITY : 2 |
| TDDRFLAG : ON TDDRTHRESHOLD: 3 SOURCEGROUPIDX : 1 |
| GDTRRULE : 0 ACDPMGRP : 0 |
| THE FOLLOWING TRUNKS (LTG-LTU-SLOT-CCT) HAVE BEEN ALLOCATED: |
+------------------------------------------------------------------------------+
| 1- 1- 25-0 1 | 1- 1- 25-0 2 | 1- 1- 25-0 3 |
| 1- 1- 25-0 4 | 1- 1- 25-0 5 | 1- 1- 25-0 6 |
| 1- 1- 25-0 7 | 1- 1- 25-0 8 | 1- 1- 25-0 9 |
| 1- 1- 25-0 10 | 1- 1- 25-0 11 | 1- 1- 25-0 12 |
| 1- 1- 25-0 13 | 1- 1- 25-0 14 | 1- 1- 25-0 15 |
| 1- 1- 25-0 16 | 1- 1- 25-0 17 | 1- 1- 25-0 18 |
| 1- 1- 25-0 19 | 1- 1- 25-0 20 | 1- 1- 25-0 21 |
| 1- 1- 25-0 22 | 1- 1- 25-0 23 | 1- 1- 25-0 24 |
| 1- 1- 25-0 25 | 1- 1- 25-0 26 | 1- 1- 25-0 27 |
| 1- 1- 25-0 28 | 1- 1- 25-0 29 | 1- 1- 25-0 30 |
+------------------------------------------------------------------------------+

AMO-BUEND-111 TRUNK GROUP
DISPLAY COMPLETED;

REGENERATE-TDCSUEN1=1-1-25-0;
H500: AMO TDCSU STARTED
ADD-TDCSU:NEW ,1-01-025-0,120,120,0,0,120,1,1,"OSO ",0
,ECMAV2,8,,NONE,,,,GDTR,N,TIE,NONE,N,0,
,,,,,
,31,MANY,1-1-101,0,1,1,EMPTY,100,1,N,
,,,,,16,8,1,10,,EC&G711&G729OPT
,"",120,CIR,Y,S2CONN,
1&&30
,N,1,1,0,0,0,0,0
;

DISPLAY-TDCSUEN1=1-1-25-0;
H500: AMO TDCSU STARTED
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2CONN PEN = 1-01-025-0 TGRP = 120 |
|---------------------------------------------------------------------------|
| PROTVAR = ECMAV2 INS = N SRCHMODE = CIR |
| COTNO = 120 COPNO = 120 DPLN = 0 |
| ITR = 0 COS = 120 LCOSV = 1 |
| LCOSD = 1 CCT = OSO DESTNO = 0 |
| SEGMENT = 8 DEDSCC = DEDSVC = NONE |
| FACILITY = DITIDX = SRTIDX = |
| TRTBL = GDTR SIDANI = N ATNTYP = TIE |
| CBMATTR = NONE NWMUXTIM = 10 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNIP = ISDNNP = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 1 -1 -101 |
| ALARMNO = 0 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 100 FWDX = 1 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = CCHDL = |
| UUSCCX = 16 UUSCCY = 8 FNIDX = 1 |
| CLASSMRK = EC & G711 & G729OPT SRCGRP = |
| TCCID = |
|---------------------------------------------------------------------------|
| BCNEG = N BCGR = 1 LWPAR = 1 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| SVCDOM = |
| BCHAN = 1 && 30 |
| |
+---------------------------------------------------------------------------+
AMOUNT OF B-CHANNELS IN THIS DISPLAY-OUTPUT: 30

AMO-TDCSU-111 DIGITAL TRUNKS
DISPLAY COMPLETED;


ADD-LODR:120,,,,ECHO,1;
ADD-LODR:120,,,,ECHO,2;
ADD-LODR:120,,,,END;
ADD-LODR:120,,,"LODR FOR E1";




DISPLAY-RICHT:MODE=LRTE,LRTE=120;
H500: AMO RICHT STARTED
+-----------------------------------------------------------------+
| LRTE = 120 NAME = E1-OSO (NEUTRAL) LSVC = VCE |
| DNNO =1 -10 -101 PDNNO = 0 |
| ROUTOPT = YES REROUT = YES PLB = NO FWDBL = NO |
| DTMFCNV = FIX DTMFDSP = WITHOUT DTMFTEXT = |
| DTMFPULS = PP300 BUGS = LIN ROUTATT = NO MAINGRP = 15 |
| EMCYRTT = NO CONFTONE = NO RERINGRP = NO RTENO = 15 |
| INFO = |
| NOPRCFWD = NO |
+-----------------------------------------------------------------+
| TGRP = 120 LDAT OSO NETWORK (NEUTRAL) SUBGROUP = 18 |
+-----------------------------------------------------------------+

AMO-RICHT-111 TRUNK ROUTING
DISPLAY COMPLETED;


REGENERATE-LDAT:LROUTE=120;
H500: AMO LDAT STARTED
ADD-LDAT:120,VCE,1,,120,120,64
,
,1,EMPTY,
NONE,
1-10-101,4,,,,
,,;

AMO-LDAT -111 LCR-DIRECTIONS



DISPLAY-LDAT:LROUTE=120;
H500: AMO LDAT STARTED
+--------------------------------------------------------------------------+
| LROUTE = 120 NAME = E1-OSO SERVICE = VCE |
| TYPE = LCR DNNO OF ROUTE = 1 -10 -101 |
| SERVICE INFO = |
+-------+-----+-----+-----+------+----------+------------+----------+------+
| | | | | | SCHEDULE | CARRIER | | |
| LRTEL | LVAL| TGRP| ODR| LAUTH| ABCDEFGH | ZONE | LATTR | LDSRT|
+-------+-----+-----+-----+------+----------+------------+----------+------+
| 1 | 1| 120| 120| 64 | ******** | 1 EMPTY | NONE | |
| | DNNO = 1 -10 -101 |
+-------+-----+-----+-----+------+----------+------------+----------+------+

AMO-LDAT -111 LCR-DIRECTIONS
DISPLAY COMPLETED;

DISPLAY-REFTA:TYPE=CIRCUIT,PEN=1-1-25;
H500: AMO REFTA STARTED
+-------------------------------------------------------------------------+
| R E F E R E N C E C L O C K C I R C U I T S |
+--------------+---------+----------+---+------+------+------+-----+------+
| PEN | MODULE | DEVICE |PRI|ERROR |BLOCK |SUPP. |READY|SRCGRP|
| | | | | | | |BUT | |
| | | | | | | |ASYN.| |
+--------------+---------+----------+---+------+------+------+-----+------+
| 1- 1- 25- 0 | DIU-N2 | S2CONN | 0| 2047| N | | N | 1|
+--------------+---------+----------+---+------+------+------+-----+------+

AMO-REFTA-111 REFERENCE CLOCK TABLE
DISPLAY COMPLETED;


DISPLAY-SDSU:TYPE=PEN,LEVEL=PER3,LTG=1,LTU=1,SLOT=25;
H500: AMO SDSU STARTED

LTG1 (PERIPHERY)
------
MOUNTING LOCATION MODULE NAME BDL BD(#=ACT) STATUS
P202.UPR 1.LTU 1.025 DIU-N2 A Q2196-X
CCT LINE STNO SI BUS TYPE
000 3238 PP NW DEPLOCK/NPR
MULTLINE 30 . . . . . . . . . . . . . .UNACH
001 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
002 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
003 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
004 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
005 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
006 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
007 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
008 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
009 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
010 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
011 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
012 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
013 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
014 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
015 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
016 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
017 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
018 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
019 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
020 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
021 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
022 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
023 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
024 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
025 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
026 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
027 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
028 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
029 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
030 NETWORK SUBUNIT . TMD CONN ISDN UNACH/CP
(S2CONN )
LINE: 3238 STNO: SI:
001 . . . . . . . . TMD CONN ISDN UNACH/CP
CCT LINE STNO SI BUS TYPE
001 3239 NOGEN

AMO-SDSU -111 STATUS DISPLAY IN SWITCHING UNIT
DISPLAY COMPLETED;


on dssu display 30 bchannel seems to bee not ready or blocket
the link between hipath and omnipcx is not established
is there any error in config please ??

 

[masviss]

One side must be a Master the other a Slave.
Parity control CRC4 is enabled or disabled?
This is seen by Hipath4000 in AMO LWPAR.
DIS-LWPAR:,,,DIUS2,1;
And
DIS-REFTA; for MASTER PRI=0, for SLAVE PRI=89 or less

 

[illios]

Crc4 is set to N
Hipath is slave and omnipcx is master
The PRA T2 CARD in alcatel show LOS and
RAI error the 30 Chanels indicate HS state
Dis-bssu show activated but not ready

 

[masviss]

Please show us
DIS-REFTA;
DIS-LWPAR:,,,DIUS2,1;

 

[Moriendi]

CRC4 is controlled by the QUAL parameter in the LWPAR and it usually doesn’t matter if it’s Y or N, as long as it matches the partner device. So find out if CRC4 is off/on for the other side and adjust accordingly.

You should be checking HISTA to see if you get L1 OK..L2 errors etc.

 

[illios]

DISPLAY-REFTA:;
H500: AMO REFTA STARTED
+-------------------------------------------------------------------------+
| R E F E R E N C E C L O C K C I R C U I T S |
+--------------+---------+----------+---+------+------+------+-----+------+
| PEN | MODULE | DEVICE |PRI|ERROR |BLOCK |SUPP. |READY|SRCGRP|
| | | | | | | |BUT | |
| | | | | | | |ASYN.| |
+--------------+---------+----------+---+------+------+------+-----+------+
| 1- 2- 61- 0 | STMD | S0CONN | 0| 65535| N | | N | 1|
| 1- 2- 61- 1 | STMD | S0COD | 60| 46106| N | | N | 1|
| 1- 1- 25- 0 | DIU-N2 | S2CONN | 89| 16383| N | X| N | 1|
+--------------+---------+----------+---+------+------+------+-----+------+


DISPLAY-LWPAR:TYPE=DIUS2,BLNO=1;
H500: AMO LWPAR STARTED

+-----------------------------------------------------------------------+
| LOADWARE PARAMETERS CIRCUIT TYPE: DIUS2 SOURCEB BLOCK: 1 |
+-----------------------------------------------------------------------+
| LNTYPE = COPPER VERSION = S2 QUAL = ON |
| MASTER = N DCHAN1 = 16 DCHAN2 = 0 |
| PATTERN = D5H QUAL1 = 10 SEC. QUAL2 = 10 MIN. |
| SMD = N PERMACT = Y FCBAB = DFH |
| CDG = N FIXEDTEI = 0 CNTRNR = 255 |
| TEIVERIF = N CRC4REP = N |
| DEV = INDEP |
| INFO = |
+-----------------------------------------------------------------------+

 

[masviss]

Everything is right. The physical connection is established. You need to choose the right protocol. What protocol is used on the alcatel side?
I think that on the HiPath side you need to install the ETSI protocol.
Show
REG-PRODE;

 

[illios]

thinks for your help
the Protocol we use is ECMVA2
IN ALCATEL the Protocol is QSIG-gf
after many attemps the PRA T2 CARD is ok
the probleme is that i have permute pins in the subb 15
of the diun2 card of port 1
now the connection is established but rest the route off calls
how to update WABE and LDPLN for ougoing and incoming calls in hipath 4000 ????
the range of call number is from 55000 to 57099 in hipath
in alcatel it begean from 57100

 

[masviss]

I'm sorry, but within the framework of this forum, I cannot conduct a training course on HP4000 programming.