francescod
Technical User
Good morning everyone,
one of our MD110 exchanges was connected to 3 ISDN NT1 studs with six lines in direct dialing with a range of 100 numbers.
The studs have been replaced by a router with 3 BRI ports. After this step we had problems with incoming calls.
Initially the user number did not exist. After an intervention by the manager, the calls reach their destination, but the direct dialing does not work.
All incoming calls to the control panel, destined for the various extensions, arrive only at the operator station.
Any suggestions? Below is an extract of the control panel configuration.
Thank you all.
<RODAP:ROU=2;ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
2 SL60 H'00000304 H'04080000 H'26410000 NO
END
<ROCAP:ROU=2;ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
2 511000010000001 5 3100000001 0 30 128 00101011 111100000030 101100
END
<SCEXP; EXTERNAL SYNC RECEIVING LINES DATA
MASTER LIM STATUS [MASTER SCOPE]
FIRST CHOICE 1-0-50-0 SYNC RECEIVING
SECOND CHOICE NOT PRESENT
THIRD CHOICE NOT PRESENT
END
<OPCGPIR=98990; OPERATOR CALL ORIGIN GROUP DATA
DIR
9
8
9
9
0
CORG -
1 0
2 2
3 2
5 1
6 1
7 2
8 1
END
<RODNP:ROU=ALL;ROUTE DAY AND NIGHT NUMBER DATA
ROU TRU DAY NIG
1 99 75521
END
<NUTRP;NUMBER CONVERSION DATA
ENTRY CNVTYP NUMTYP ROU PRE TRC NEWTYP CONT BCAP HLC
8845445 0 2 755 7 0
755 1 10 3 0
98990 1 10 00 5 0
98990 1 11 75500 5 0
3 2 0 0 0
1 2 1 000 0
2 2 1 00 0
3 2 1 00 0
4 2 1 00 0
5 2 1 00 0
6 2 1 00 0
7 2 1 00 0
8 2 1 00 0
9 2 1 00 0
1 2 2 00 0
2 2 2 0 0
3 2 2 00 0
4 2 2 0 0
5 2 2 0 0
6 2 2 0 0
7 2 2 0 0
8 2 2 0 0
9 2 2 0 0
END
one of our MD110 exchanges was connected to 3 ISDN NT1 studs with six lines in direct dialing with a range of 100 numbers.
The studs have been replaced by a router with 3 BRI ports. After this step we had problems with incoming calls.
Initially the user number did not exist. After an intervention by the manager, the calls reach their destination, but the direct dialing does not work.
All incoming calls to the control panel, destined for the various extensions, arrive only at the operator station.
Any suggestions? Below is an extract of the control panel configuration.
Thank you all.
<RODAP:ROU=2;ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
2 SL60 H'00000304 H'04080000 H'26410000 NO
END
<ROCAP:ROU=2;ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
2 511000010000001 5 3100000001 0 30 128 00101011 111100000030 101100
END
<SCEXP; EXTERNAL SYNC RECEIVING LINES DATA
MASTER LIM STATUS [MASTER SCOPE]
FIRST CHOICE 1-0-50-0 SYNC RECEIVING
SECOND CHOICE NOT PRESENT
THIRD CHOICE NOT PRESENT
END
<OPCGPIR=98990; OPERATOR CALL ORIGIN GROUP DATA
DIR
9
8
9
9
0
CORG -
1 0
2 2
3 2
5 1
6 1
7 2
8 1
END
<RODNP:ROU=ALL;ROUTE DAY AND NIGHT NUMBER DATA
ROU TRU DAY NIG
1 99 75521
END
<NUTRP;NUMBER CONVERSION DATA
ENTRY CNVTYP NUMTYP ROU PRE TRC NEWTYP CONT BCAP HLC
8845445 0 2 755 7 0
755 1 10 3 0
98990 1 10 00 5 0
98990 1 11 75500 5 0
3 2 0 0 0
1 2 1 000 0
2 2 1 00 0
3 2 1 00 0
4 2 1 00 0
5 2 1 00 0
6 2 1 00 0
7 2 1 00 0
8 2 1 00 0
9 2 1 00 0
1 2 2 00 0
2 2 2 0 0
3 2 2 00 0
4 2 2 0 0
5 2 2 0 0
6 2 2 0 0
7 2 2 0 0
8 2 2 0 0
9 2 2 0 0
END