Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

IA770 on S8400

Status
Not open for further replies.

GuzaPasha

Technical User
May 15, 2003
311
FR
Hi all,

have there been any problems seen with the installation of IA770 on S8400/G650, CM3.1.2?

Does anyone has step by step documentation for installing IA770 on S8400 (CM3.1.2)? I have tried everything and messaging service are always down!

Does it matter to which interface is assigned Processor Ethernet (Control Network A or Enterprise LAN)? Do I need to add IP-interface procr? Also, in AIW I don't have field for messaging IP address, I must fill it thru Maintenance Web Interface/Configure Server, is this normal?

Thanks in advance,

Bst Rgds
 
If you powered down without having the proper patches applied, you probably corrupted the database, thus it will never start.

Unless you've got a backup from before the corruption, you'll need to call Avaya to get the database rebuilt.

I did this like 5 times before I made a backup of a blank IA770 to keep on hand for stuff like this...

P.S. It's more of an IA770 running on CM3.1.2 vs. running on the S8400....
 
thanx sjforcum

but this is initial installation of IA770??!! Do you told me to do backup of IA770 immediately after installation?
 
You bet.

If you did NOT patch the IA770 before a reboot (even a graceful one), you're hosed.

SJF
 
BTW This is a known problem with CM3.1.2....
 
OK, thanx again sjforcum

I tried to run installation from the beginning, and put patch A6086rf+b, but still no progress!!! Is this good way?
Can I try to install CM3.1.1 and solve this problem?

Bst Rgds

GP


 
YOu need the Audix patch AND the cornerstone patch....
 
thanx sjforcum,

your tips was very helpful! thanx a lot!!!!!
Yesterday afternoon service was up, but when I came this morning at the work messaging service was down and I can't make it to work!???
Did you have similar experience? what can I do? Maybe to try with CM3.1.1, this is happening on CM3.1.2


 
when I try to start messaging software I get this message:

Begin: start_vs Tue Feb 13 10:11:35 CET 2007
H323Card process already enabled.
H323fax process already enabled.
aspfs process already disabled.
spip process already disabled.
cioX process already disabled.
vrop process already disabled.
ehs process already disabled.
startup process already disabled.
vaa process already disabled.
vlip process already disabled.
Executing: /vs/bin/util/startup.d/audit_smdb
Using /mtce/db for dbd path instead of /vs/data/swin/db
Using /mtce/db for dbf path instead of /vs/data/swin/db
Auditing Database /vs/data/swin/db/sm_db ...
Database /vs/data/swin/db/sm_db is good.
Executing: /vs/bin/util/startup.d/chk4express
Executing: /vs/bin/util/startup.d/chk_restore
Executing: /vs/bin/util/startup.d/clrmach
End: start_vs Tue Feb 13 10:11:39 CET 2007
Tue Feb 13 10:11:39 CET 2007
 
Telnet into the S8400 and type "start -s Audix". Then type "statapp -U". See if the Messaging Service comes on-line.

I would also try re-booting to start fresh...I don't know how many IA770's you've worked on but they take a LONG time (like litterally 5-10 minutes) to come on-line. Once the server powers on, telnet in and run STATAPP -U. It will refresh continually until ALL services come on-line.
 
Thanx sjforcum , you helped me to resolve this issue! without you I couldn't make it!
thanx again

Bst Rgds
 
can you shed some light on the reinstall. I have the same exact problem with a 4.0 install. the only difference with my issue is that the start -s audix command tells me that audix is already running.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top