dmb2002man
MIS
I need help asap since this router is going to california tommorow and i cant seem to get the upgrade working. I have installed the new rom boot chip and new flash. The router boots up to rommon prompt. I tried to xmodem a bin but it says not enough memory everytime. I have no idea what else to do. I have tried searching online too and called cisco and left a message but no call back yet as of tonight. I tried to do disaster recovery but im not sure how to communicate it with the tftp server since it doesnt have no ip address, i just made the one up below. Does anyone know what i could do, please help me out asap.
thanks
Josh
opyright (c) 1999 by cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info
C2600 platform with 65536 Kbytes of main memory
get_man_dev: Unknown device - probably NOT formatted.
unknown flash device - mandev code = 0xffff
cannot read flash info
getdevnum warning: device "flash" has size of zero
get_man_dev: Unknown device - probably NOT formatted.
unknown flash device - mandev code = 0xffff
cannot read flash info
getdevnum warning: device "flash" has size of zero
open: read error...requested 0x4 bytes, got 0x0
trouble reading device magic number
boot: cannot open "flash:"
boot: cannot determine first file name on device "flash:"
System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info
C2600 platform with 65536 Kbytes of main memory
rommon 1 >
rommon 2 >
rommon 2 >
rommon 2 > ?
alias set and display aliases command
boot boot up an external process
break set/show/clear the breakpoint
confreg configuration register utility
cont continue executing a downloaded image
context display the context of a loaded image
cookie display contents of cookie PROM in hex
dev list the device table
dir list files in file system
dis display instruction stream
dnld serial download a program module
frame print out a selected stack frame
help monitor builtin command help
history monitor command history
meminfo main memory information
repeat repeat a monitor command
reset system reset
set display the monitor variables
stack produce a stack trace
sync write monitor environment to NVRAM
sysret print out info from last system return
tftpdnld tftp image download
unalias unset an alias
unset unset a monitor variable
xmodem x/ymod
rommon 3 > xmodem -c c2600-j1s3-mz.123-22.bin
Do not start the sending program yet...
get_man_dev: Unknown device - probably NOT formatted.
unknown flash device - mandev code = 0xffff
cannot read flash info
getdevnum warning: device "flash" has size of zero
get_man_dev: Unknown device - probably NOT formatted.
unknown flash device - mandev code = 0xffff
cannot read flash info
getdevnum warning: device "flash" has size of zero
open: read error...requested 0x4 bytes, got 0x0
trouble reading device magic number
dir: cannot open device "flash:"
WARNING: All existing data in bootflash will be lost!
Invoke this application only for disaster recovery.
Do you wish to continue? y/n [n]: y
get_man_dev: Unknown device - probably NOT formatted.
unknown flash device - mandev code = 0xffff
cannot read flash info
ERR: Not enough memory to download image
rommon 4 > xmodem -c c2600-js-mz.121-27b.bin
Do not start the sending program yet...
get_man_dev: Unknown device - probably NOT formatted.
unknown flash device - mandev code = 0x
cannot read flash info
getdevnum warning: device "flash" has size of zero
get_man_dev: Unknown device - probably NOT formatted.
unknown flash device - mandev code = 0xffff
cannot read flash info
getdevnum warning: device "flash" has size of zero
open: read error...requested 0x4 bytes, got 0x0
trouble reading device magic number
dir: cannot open device "flash:"
WARNING: All existing data in bootflash will be lost!
Invoke this application only for disaster recovery.
Do you wish to continue? y/n [n]: y
get_man_dev: Unknown device - probably NOT formatted.
unknown flash device - mandev code = 0xffff
cannot read flash info
ERR: Not enough memory to download image
rommon 5 >
System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info
C2600 platform with 65536 Kbytes of main memory
program load complete, entry point: 0x80008000, size: 0x403b9c
Self decompressing the image : #################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################## [OK]
Restricted Rights Legend
Use, duplication, or disclosure
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.0(7)T, RELEASE SOFTWARE (fc2)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Tue 07-Dec-99 02:12 by phanguye
Image text-base: 0x80008088, data-base: 0x807AAF70
cisco 2610 (MPC860) processor (revision 0x300) with 53248K/12288K bytes of memor
y.
Processor board ID JAD05510D3M (1695631240)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]: n
Press RETURN to get started!
00:00:08: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed s
tate to down
00:00:26: %LINK-5-CHANGED: Interface Ethernet0/0, changed state to administrativ
ely down
00:00:28: %IP-5-WEBINST_KILL: Terminating DNS process
00:00:34: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.0(7)T, RELEASE SOFTWARE (fc2)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Tue 07-Dec-99 02:12 by phanguye
System Bootstrap, Version 12.2(10r)1, RELEASE SOFTWARE (fc1)
TAC Support: Copyright (c) 2002 by cisco Systems, Inc.
C2600 platform with 65536 Kbytes of main memory
getdevnum warning: device "flash" has size of zero
getdevnum warning: device "flash" has size of zero
open: read error...requested 0x4 bytes, got 0x0
trouble reading device magic number
boot: cannot open "flash:"
boot: cannot determine first file name on device "flash:"
System Bootstrap, Version 12.2(10r)1, RELEASE SOFTWARE (fc1)
TAC Support: Copyright (c) 2002 by cisco Systems, Inc.
C2600 platform with 65536 Kbytes of main memory
getdevnum warning: device "flash" has size of zero
getdevnum warning: device "flash" has size of zero
open: read error...requested 0x4 bytes, got 0x0
trouble reading device magic number
boot: cannot open "flash:"
boot: cannot determine first file name on device "flash:"
System Bootstrap, Version 12.2(10r)1, RELEASE SOFTWARE (fc1)
TAC Support: Copyright (c) 2002 by cisco Systems, Inc.
C2600 platform with 65536 Kbytes of main memory
rommon 1 > ip address 192.168.2.20
monitor: command "ip" not found
rommon 2 > ip_address=192.168.2.20
rommon 3 > ip_subnet_mask=255.255.255.0
rommon 4 > default_gateway=192.168.2.100
rommon 5 > tftp_server=1
rommon 6 > tftp_file=c2600-ik9o3s-mz.122-40a.bin
rommon 7 > tftpdnid
monitor: command "tftpdnid" not found
rommon 8 > tftpdnld
Missing or illegal ip address for variable IP_ADDRESS
Illegal IP address.
usage: tftpdnld [-r]
Use this command for disaster recovery only to recover an image via TFTP.
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
IP_ADDRESS: The IP address for this unit
IP_SUBNET_MASK: The subnet mask for this unit
DEFAULT_GATEWAY: The default gateway for this unit
TFTP_SERVER: The IP address of the server to fetch from
TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
TFTP_RETRY_COUNT: Retry count for ARP and TFTP (de
TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx, 4=Auto(deflt)
Command line options:
-r: do not write flash, load to DRAM only and launch image
rommon 9 > ip_address=192.168.2.1
rommon 10 > tftpdnld
Missing or illegal ip address for variable IP_ADDRESS
Illegal IP address.
usage: tftpdnld [-r]
Use this command for disaster recovery
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
IP_ADDRESS: The IP address for this unit
IP_SUBNET_MASK: The subnet mask for this unit
DEFAULT_GATEWAY: The default gateway for this unit
TFTP_SERVER: The IP address of the server to fetch from
TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=7)
TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx, 4=Auto(deflt)
Command line options:
-r: do not write flash, load to DRAM only and launch image
rommon 11 > ip_address=192.168.0.0
rommon 12 > tftpdnld
Missing or illegal ip address for variable IP_ADDRESS
Illegal IP address.
usage: tftpdnld [-r]
Use this command for disaster recovery only to recover an image via TFTP.
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
IP_ADDRESS: The IP address for this unit
IP_SUBNET_MASK: The subnet mask for this unit
DEFAULT_GATEWAY: The default gateway for this unit
TFTP_SERVER: The IP address of the server to fetch from
TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
TFTP_RETRY_COUNT: Retry count for ARP and TFTP (de
TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx, 4=Auto(deflt)
Command line options:
-r: do not write flash, load to DRAM only and launch image
rommon 13 > tftpdnld -r
Missing or illegal ip address for variable IP_ADDRESS
Illegal IP address.
usage: tftpdnld [-r]
Use this command for disaster recovery only to recover an image via T
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
IP_ADDRESS: The IP address for this unit
IP_SUBNET_MASK: The subnet mask for this unit
DEFAULT_GATEWAY: The default gateway for this unit
TFTP_SERVER: The IP address of the server to fetch from
TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=7)
TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx, 4=Auto(deflt)
Command line options:
-r: do not write flash, load to DRAM only and launch image
rommon 14 > ip_address=192.168.2.50
rommon 15 > tftpdnld
Missing or illegal ip address for variable IP_ADDRESS
Illegal IP address.
usage: tftpdnld [-r]
Use this command for disaster recovery only to recover an image via TFTP.
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
IP_ADDRESS: The IP address for this unit
IP_SUBNET_MASK: The subnet mask for this unit
DEFAULT_GATEWAY: The default gateway for this unit
TFTP_SERVER: The IP address of the server to fetch from
TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
TFTP_RETRY_COUNT: Retry count for ARP and TFTP (de
TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx, 4=Auto(deflt)
Command line options:
-r: do not write flash, load to DRAM only and launch image
rommon 16 >
System Bootstrap, Version 12.2(10r)1, RELEASE SOFTWARE (fc1)
TAC Support: Copyright (c) 2002 by cisco Systems, Inc.
C2600 platform with 65536 Kbytes of ma
getdevnum warning: device "flash" has size of zero
progr
getdevnum warning: device "flash" has size of zero403b9c
open: read error...requested 0x4 bytes, got 0x0: #############################################
trouble reading device magic number
boot: cannot open "flash:"##########################
boot: cannot determine first file name on device "flash:"
System Bootstrap, Version 12.2(10r)1, RELEASE SOFTWARE (fc1)#########################
TAC Support: #############################
Copyright (c) 2002 by cisco Systems, Inc.#########
C2600 platform with 65536 Kbytes of main memory
##############################################
getdevnum warning: device "flash" has size of zero
Restricted
boot: cannot open "flash:"
boot: cannot determine first file name on device "flash:"
subject to
System Bootstrap, Version 12.2(10r)1, RELEASE SOFTWARE (fc1)
(c) of the Commercial Compu
TAC Support: Copyright (c) 2002 by cisco Systems, Inc. subparagraph
C2600 platform with 65536 Kbytes of main memoryhts in Technical Data and Computer
rommon 1 > ip_address=192.168.2.0
Software clause at DFAR
rommon 2 > ip_subnet_mask=255.255.255.0
cis
rommon 3 > default_gateway=192.168
usage: tftpdnld [-r]
Use this command for disaster recovery only to recover an image via TFTP.
Compiled Tue 07-Dec-99 02:12 by phanguye
Monitor variables are used to set up parameters for the transfer.x807AAF70
cisco
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
M860 processor: part number 0, mask 4
System Bootstrap, Ver
TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:ems, Inc.
TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verboseC2600 platform with 65536 Kbytes of main memory
TFTP_RETRY_COUNT: Retry count for ARP and TFTP (deNOT form
cannot read flash info
ge
Command line options:flash" has size of zero
-r: do not write flash, load to DRAM only and launch imageerror...requested 0
PS1=rommon ! >
RET_2_RTS=
BSI=0
RET_2_RCALTS=
ip_address=192.168.2.0
ip_subnet_mask=255.255.255.0
default_gateway=192.168.2.100
tftp_server=192.168.2.28
tftp_file=c2600-ik9o3s-mz.122-40a.bin
?=1
rommon 9 > xmodem c2600-js-mz.121-27b.bin
Do not start the sending program yet...
getdevnum warning: device "flash" has size of zero
getdevnum warning: device "flash" has size of zero
open: read error...requested 0x4 bytes, got 0x0
trouble reading device magic number
dir: cannot open device "flash:"
WARNING: All existing data in bootflash will be lost!
Invoke this application only for disaster recovery.
Do you wish to continue? y/n [n]: y
ERR: Not enough memory to download image
rommon 10 >
thanks
Josh
opyright (c) 1999 by cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info
C2600 platform with 65536 Kbytes of main memory
get_man_dev: Unknown device - probably NOT formatted.
unknown flash device - mandev code = 0xffff
cannot read flash info
getdevnum warning: device "flash" has size of zero
get_man_dev: Unknown device - probably NOT formatted.
unknown flash device - mandev code = 0xffff
cannot read flash info
getdevnum warning: device "flash" has size of zero
open: read error...requested 0x4 bytes, got 0x0
trouble reading device magic number
boot: cannot open "flash:"
boot: cannot determine first file name on device "flash:"
System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info
C2600 platform with 65536 Kbytes of main memory
rommon 1 >
rommon 2 >
rommon 2 >
rommon 2 > ?
alias set and display aliases command
boot boot up an external process
break set/show/clear the breakpoint
confreg configuration register utility
cont continue executing a downloaded image
context display the context of a loaded image
cookie display contents of cookie PROM in hex
dev list the device table
dir list files in file system
dis display instruction stream
dnld serial download a program module
frame print out a selected stack frame
help monitor builtin command help
history monitor command history
meminfo main memory information
repeat repeat a monitor command
reset system reset
set display the monitor variables
stack produce a stack trace
sync write monitor environment to NVRAM
sysret print out info from last system return
tftpdnld tftp image download
unalias unset an alias
unset unset a monitor variable
xmodem x/ymod
rommon 3 > xmodem -c c2600-j1s3-mz.123-22.bin
Do not start the sending program yet...
get_man_dev: Unknown device - probably NOT formatted.
unknown flash device - mandev code = 0xffff
cannot read flash info
getdevnum warning: device "flash" has size of zero
get_man_dev: Unknown device - probably NOT formatted.
unknown flash device - mandev code = 0xffff
cannot read flash info
getdevnum warning: device "flash" has size of zero
open: read error...requested 0x4 bytes, got 0x0
trouble reading device magic number
dir: cannot open device "flash:"
WARNING: All existing data in bootflash will be lost!
Invoke this application only for disaster recovery.
Do you wish to continue? y/n [n]: y
get_man_dev: Unknown device - probably NOT formatted.
unknown flash device - mandev code = 0xffff
cannot read flash info
ERR: Not enough memory to download image
rommon 4 > xmodem -c c2600-js-mz.121-27b.bin
Do not start the sending program yet...
get_man_dev: Unknown device - probably NOT formatted.
unknown flash device - mandev code = 0x
cannot read flash info
getdevnum warning: device "flash" has size of zero
get_man_dev: Unknown device - probably NOT formatted.
unknown flash device - mandev code = 0xffff
cannot read flash info
getdevnum warning: device "flash" has size of zero
open: read error...requested 0x4 bytes, got 0x0
trouble reading device magic number
dir: cannot open device "flash:"
WARNING: All existing data in bootflash will be lost!
Invoke this application only for disaster recovery.
Do you wish to continue? y/n [n]: y
get_man_dev: Unknown device - probably NOT formatted.
unknown flash device - mandev code = 0xffff
cannot read flash info
ERR: Not enough memory to download image
rommon 5 >
System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info
C2600 platform with 65536 Kbytes of main memory
program load complete, entry point: 0x80008000, size: 0x403b9c
Self decompressing the image : #################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################## [OK]
Restricted Rights Legend
Use, duplication, or disclosure
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.0(7)T, RELEASE SOFTWARE (fc2)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Tue 07-Dec-99 02:12 by phanguye
Image text-base: 0x80008088, data-base: 0x807AAF70
cisco 2610 (MPC860) processor (revision 0x300) with 53248K/12288K bytes of memor
y.
Processor board ID JAD05510D3M (1695631240)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]: n
Press RETURN to get started!
00:00:08: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed s
tate to down
00:00:26: %LINK-5-CHANGED: Interface Ethernet0/0, changed state to administrativ
ely down
00:00:28: %IP-5-WEBINST_KILL: Terminating DNS process
00:00:34: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.0(7)T, RELEASE SOFTWARE (fc2)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Tue 07-Dec-99 02:12 by phanguye
System Bootstrap, Version 12.2(10r)1, RELEASE SOFTWARE (fc1)
TAC Support: Copyright (c) 2002 by cisco Systems, Inc.
C2600 platform with 65536 Kbytes of main memory
getdevnum warning: device "flash" has size of zero
getdevnum warning: device "flash" has size of zero
open: read error...requested 0x4 bytes, got 0x0
trouble reading device magic number
boot: cannot open "flash:"
boot: cannot determine first file name on device "flash:"
System Bootstrap, Version 12.2(10r)1, RELEASE SOFTWARE (fc1)
TAC Support: Copyright (c) 2002 by cisco Systems, Inc.
C2600 platform with 65536 Kbytes of main memory
getdevnum warning: device "flash" has size of zero
getdevnum warning: device "flash" has size of zero
open: read error...requested 0x4 bytes, got 0x0
trouble reading device magic number
boot: cannot open "flash:"
boot: cannot determine first file name on device "flash:"
System Bootstrap, Version 12.2(10r)1, RELEASE SOFTWARE (fc1)
TAC Support: Copyright (c) 2002 by cisco Systems, Inc.
C2600 platform with 65536 Kbytes of main memory
rommon 1 > ip address 192.168.2.20
monitor: command "ip" not found
rommon 2 > ip_address=192.168.2.20
rommon 3 > ip_subnet_mask=255.255.255.0
rommon 4 > default_gateway=192.168.2.100
rommon 5 > tftp_server=1
rommon 6 > tftp_file=c2600-ik9o3s-mz.122-40a.bin
rommon 7 > tftpdnid
monitor: command "tftpdnid" not found
rommon 8 > tftpdnld
Missing or illegal ip address for variable IP_ADDRESS
Illegal IP address.
usage: tftpdnld [-r]
Use this command for disaster recovery only to recover an image via TFTP.
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
IP_ADDRESS: The IP address for this unit
IP_SUBNET_MASK: The subnet mask for this unit
DEFAULT_GATEWAY: The default gateway for this unit
TFTP_SERVER: The IP address of the server to fetch from
TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
TFTP_RETRY_COUNT: Retry count for ARP and TFTP (de
TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx, 4=Auto(deflt)
Command line options:
-r: do not write flash, load to DRAM only and launch image
rommon 9 > ip_address=192.168.2.1
rommon 10 > tftpdnld
Missing or illegal ip address for variable IP_ADDRESS
Illegal IP address.
usage: tftpdnld [-r]
Use this command for disaster recovery
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
IP_ADDRESS: The IP address for this unit
IP_SUBNET_MASK: The subnet mask for this unit
DEFAULT_GATEWAY: The default gateway for this unit
TFTP_SERVER: The IP address of the server to fetch from
TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=7)
TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx, 4=Auto(deflt)
Command line options:
-r: do not write flash, load to DRAM only and launch image
rommon 11 > ip_address=192.168.0.0
rommon 12 > tftpdnld
Missing or illegal ip address for variable IP_ADDRESS
Illegal IP address.
usage: tftpdnld [-r]
Use this command for disaster recovery only to recover an image via TFTP.
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
IP_ADDRESS: The IP address for this unit
IP_SUBNET_MASK: The subnet mask for this unit
DEFAULT_GATEWAY: The default gateway for this unit
TFTP_SERVER: The IP address of the server to fetch from
TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
TFTP_RETRY_COUNT: Retry count for ARP and TFTP (de
TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx, 4=Auto(deflt)
Command line options:
-r: do not write flash, load to DRAM only and launch image
rommon 13 > tftpdnld -r
Missing or illegal ip address for variable IP_ADDRESS
Illegal IP address.
usage: tftpdnld [-r]
Use this command for disaster recovery only to recover an image via T
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
IP_ADDRESS: The IP address for this unit
IP_SUBNET_MASK: The subnet mask for this unit
DEFAULT_GATEWAY: The default gateway for this unit
TFTP_SERVER: The IP address of the server to fetch from
TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=7)
TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx, 4=Auto(deflt)
Command line options:
-r: do not write flash, load to DRAM only and launch image
rommon 14 > ip_address=192.168.2.50
rommon 15 > tftpdnld
Missing or illegal ip address for variable IP_ADDRESS
Illegal IP address.
usage: tftpdnld [-r]
Use this command for disaster recovery only to recover an image via TFTP.
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
IP_ADDRESS: The IP address for this unit
IP_SUBNET_MASK: The subnet mask for this unit
DEFAULT_GATEWAY: The default gateway for this unit
TFTP_SERVER: The IP address of the server to fetch from
TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
TFTP_RETRY_COUNT: Retry count for ARP and TFTP (de
TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx, 4=Auto(deflt)
Command line options:
-r: do not write flash, load to DRAM only and launch image
rommon 16 >
System Bootstrap, Version 12.2(10r)1, RELEASE SOFTWARE (fc1)
TAC Support: Copyright (c) 2002 by cisco Systems, Inc.
C2600 platform with 65536 Kbytes of ma
getdevnum warning: device "flash" has size of zero
progr
getdevnum warning: device "flash" has size of zero403b9c
open: read error...requested 0x4 bytes, got 0x0: #############################################
trouble reading device magic number
boot: cannot open "flash:"##########################
boot: cannot determine first file name on device "flash:"
System Bootstrap, Version 12.2(10r)1, RELEASE SOFTWARE (fc1)#########################
TAC Support: #############################
Copyright (c) 2002 by cisco Systems, Inc.#########
C2600 platform with 65536 Kbytes of main memory
##############################################
getdevnum warning: device "flash" has size of zero
Restricted
boot: cannot open "flash:"
boot: cannot determine first file name on device "flash:"
subject to
System Bootstrap, Version 12.2(10r)1, RELEASE SOFTWARE (fc1)
(c) of the Commercial Compu
TAC Support: Copyright (c) 2002 by cisco Systems, Inc. subparagraph
C2600 platform with 65536 Kbytes of main memoryhts in Technical Data and Computer
rommon 1 > ip_address=192.168.2.0
Software clause at DFAR
rommon 2 > ip_subnet_mask=255.255.255.0
cis
rommon 3 > default_gateway=192.168
usage: tftpdnld [-r]
Use this command for disaster recovery only to recover an image via TFTP.
Compiled Tue 07-Dec-99 02:12 by phanguye
Monitor variables are used to set up parameters for the transfer.x807AAF70
cisco
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
M860 processor: part number 0, mask 4
System Bootstrap, Ver
TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:ems, Inc.
TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verboseC2600 platform with 65536 Kbytes of main memory
TFTP_RETRY_COUNT: Retry count for ARP and TFTP (deNOT form
cannot read flash info
ge
Command line options:flash" has size of zero
-r: do not write flash, load to DRAM only and launch imageerror...requested 0
PS1=rommon ! >
RET_2_RTS=
BSI=0
RET_2_RCALTS=
ip_address=192.168.2.0
ip_subnet_mask=255.255.255.0
default_gateway=192.168.2.100
tftp_server=192.168.2.28
tftp_file=c2600-ik9o3s-mz.122-40a.bin
?=1
rommon 9 > xmodem c2600-js-mz.121-27b.bin
Do not start the sending program yet...
getdevnum warning: device "flash" has size of zero
getdevnum warning: device "flash" has size of zero
open: read error...requested 0x4 bytes, got 0x0
trouble reading device magic number
dir: cannot open device "flash:"
WARNING: All existing data in bootflash will be lost!
Invoke this application only for disaster recovery.
Do you wish to continue? y/n [n]: y
ERR: Not enough memory to download image
rommon 10 >
