I just did an install yesterday and

[j.flanagan]

I just did an install yesterday and the Office uses an after hours answering service to handle calls. Previously they would just seize line 1 and dial *72 XXX-XXXX to forward their main number to the answering service. I was hoping to IPO forwarding functions to accomplish that but ran into some DTMF issue once the calls were forwarded to the answering service. So, temporarily I was going to set them up with a button that would grab line 1 and dial that number to forward.

I created a button that uses the "Dial" function to dial *97.
I created a short code *97 that Dials 9*72XXX-XXXX but when you press that button you get a busy tone back... so I tried all these combos
9D*72Dxxx-xxxx
9*72Dxxx-xxxx
9D*72xxx-xxxx
9,,*72,,xxx-xxxx
but ever time I just get that busy tone. However, if I manually give a phone an appearance for line 1, I can select line 1 and dial 9*72xxx-xxxx

What am I missing? one of the selling points of this was to streamline their forwarding process.

 

[j.flanagan]

FYI, there is no *72 short code on the system

 

[Westi]

line appearance for Line 1
then pick it up and dial *72xxxxx

Joe
FHandw, ACSS (SME)

Remembering intrigrant 2019

 

[budbyrd]

9Y*72Yxxx-xxxx might work. Y waits for progress tone. D waits for an actual connect. I have done this before but I would have to look up the config to verify what I did.

Dermis and feline can be divorced by manifold methods.*
*(Disclaimer for all advise given)--'Version Dependent'

 

[Billxx]

You said:
I created a button that uses the "Dial" function to dial *97.
I created a short code *97 that Dials 9*72XXX-XXXX but when you press that button you get a busy tone back...

I have not worked on this system for awhile, but this may be the answer.

You are trying to grab CO Line 1 to use the Call Forwarding from the Telco Provider.
But, in each case you are dialing 9 and that selects the last CO Line, not the first.

You could try reversing the physical connection of CO Lines from 1, 2, 3,4 in the KSU to be 4,3,2,1.

Or whatever your CO Line range is.

 

[icet500]

In you short code *97 that you have created. Is it using Ars or outgoing grp id? make sure you include *72 on your ars.
otherwise, you can set a line appearnce button, push it and dial *72 XXXXXXX.

 

[TouchToneTommy]

ARS table picks the most idle line, NOT the first nor the last on the system, unless it also happens to be the one that was idle the longest.

Put Line 1 in its own Outgoing Line Group. Copy and paste the Main ARS, change the Line Group number to the new one for Line 1, and make this new ARS the Alternate Route for the Main ARS

Make your short code *97 / Dial / *72,,XXX-XXXX / Outgoing Line Group for Line 1

 

[j.flanagan]

I have line 1's outgoing group ID set to 1 and the short code is set to use group ID 1. So, it should be grabbing that 1st line for the call.

icet500, can you explain why/how to put *72 in the ars? 9N > N is in the ars. I assume that means that when 9,*72,xxx-xxxx is dialed it strips the 9 and sends the rest. Do i need to set an ars line to dial 9*72N>*72N ?

Westi, I can do it manually. However, I'm hoping to simplify the process for them.

I'll try using the Y character in my short code.

 

[j.flanagan]

Tried the 9Y*72Yxxx-xxxx but had no luck. I'll post a trace of what happens. just to clarify. I have shortcode *97 set up as a dial function using line group 1 or ARS Route :50( I think) which includes line group 1. Here's the trace.

UNICODE-UTF8
enu

********** Warning: Logging to Screen Started **********
09:20:27 1013551mS CMExtnEvt: v=(null) State, new=Idle old=Idle,0,0,139: Digit Key Pressed *
09:20:27 1013552mS CMCallEvt: 0000000000000000 0.1070.0 -1 BaseEP: NEW CMEndpoint f5b79fac TOTAL NOW=1 CALL_LIST=0
09:20:27 1013552mS CMCallEvt: 0000000000000000 0.1070.0 -1 Carolyn.-1: NEW CMExtnEndpoint f5b79fac, Name=Carolyn, Extn=139, Phys Extn=139
09:20:27 1013552mS CMCallEvt: CREATE CALL:15 (f18101fc)
09:20:27 1013553mS CMCallEvt: 0000000000000000 0.1071.0 -1 BaseEP: NEW CMEndpoint f180e5bc TOTAL NOW=2 CALL_LIST=0
09:20:27 1013555mS CMExtnEvt: Carolyn: CMExtnHandler::SetCurrent( id: 0->1070 )
09:20:27 1013555mS CMExtnRx: v=139, p1=0
CMSetup
Line: type=DigitalExtn 4 Call: lid=0 id=1070 in=0
Called[] Type=Default (100) Reason=CMDRdirect Calling[139] Type=Internal Plan=Default
BC: CMTC=Speech CMTM=CallIndSigCon CMTR=64 CMST=Default CMU1=ULaw
IE CMIECallingPartyName (110)(Type=CMNameInternalUser) name=Carolyn
IE CMIECallingPartyKName (226)(Type=CMNameDefault) name=Carolyn
09:20:27 1013555mS CMExtnRxC: v=139
CMSetup
Line: type=DigitalExtn 4 Call: lid=0 id=1070 in=0
Called[] Type=Default (100) Reason=CMDRdirect Calling[139] Type=Internal Plan=Default
BC: CMTC=Speech CMTM=CallIndSigCon CMTR=64 CMST=Default CMU1=ULaw
BChan: slot=20 chan=8
IE CMIECallingPartyName (110)(Type=CMNameInternalUser) name=Carolyn
IE CMIECallingPartyKName (226)(Type=CMNameDefault) name=Carolyn
IE CMIERespondingPartyName (228)(Type=CMNameInternalUser) name=Carolyn
IE CMIERespondingPartyKName (229)(Type=CMNameDefault) name=Carolyn
IE CMIERespondingPartyNumber (230)(P:100 S:100 T:101 N:100 R:4) number=139
IE CMIEDeviceDetail (231) ac14017a0000042e LOCALE=enu HW=15 VER=11 class=CMDeviceStdPhone type=78 number=24 channel=0 features=0x10000400 rx_gain=32 tx_gain=32
ep_callid=1070 ipaddr=172.20.1.122 apps=0 loc=0 em_a_loc=1 em_d_loc=0 features2=0x20 is_spcall=0 ignores_dtmf=0 avgsid=
09:20:27 1013556mS CMCallEvt: ac14017a0000042e 0.1070.0 15 Carolyn.0: StateChange: END=A CMCSIdle->CMCSDialInitiated
09:20:27 1013556mS CMExtnEvt: v=8 State, new=Dialling old=Idle,0,0,Carolyn
09:20:27 1013556mS CMTARGET: ac14017a0000042e 0.1070.0 15 Carolyn.0: LOOKUP CALL ROUTE: GID=0 type=100 called_party= sub= calling=139 calling_sub= dir=out complete=0 ses=0
09:20:27 1013557mS CMTARGET: ac14017a0000042e 0.1070.0 15 Carolyn.0: ADD TARGET (N): number= type=100 depth=1 nobar=1 setorig=1 ses=0
09:20:27 1013557mS CMCallEvt: ac14017a0000042e 0.1070.0 15 Carolyn.0: StateChange: END=A CMCSDialInitiated->CMCSDialling
09:20:27 1013557mS CMExtnTxC: v=139
CMSetupAck
Line: type=NoLine 0 Call: lid=0 id=1070 in=0
09:20:27 1013558mS CMExtnTx: v=139, p1=0
CMSetupAck
Line: type=DigitalExtn 4 Call: lid=0 id=1070 in=0
BChan: slot=20 chan=8
Timed: 06/07/20 09:20
09:20:27 1013558mS CMExtnRx: v=139, p1=0
CMInformation
Line: type=DigitalExtn 4 Call: lid=0 id=1070 in=0
Called[*] Type=Default (100) Reason=CMDRdirect Keypad[*]
09:20:27 1013558mS CMExtnRxC: v=139
CMInformation
Line: type=DigitalExtn 4 Call: lid=0 id=1070 in=0
Called[*] Type=Default (100) Reason=CMDRdirect Keypad[*]
BChan: slot=20 chan=8
IE CMIERespondingPartyName (228)(Type=CMNameInternalUser) name=Carolyn
IE CMIERespondingPartyKName (229)(Type=CMNameDefault) name=Carolyn
IE CMIERespondingPartyNumber (230)(P:100 S:100 T:101 N:100 R:4) number=139
IE CMIEDeviceDetail (231) ac14017a0000042e LOCALE=enu HW=15 VER=11 class=CMDeviceStdPhone type=78 number=24 channel=0 features=0x10000420 rx_gain=32 tx_gain=32
ep_callid=1070 ipaddr=172.20.1.122 apps=0 loc=0 em_a_loc=1 em_d_loc=0 features2=0x20 is_spcall=0 ignores_dtmf=0 avgsid=
09:20:27 1013558mS CMTARGET: ac14017a0000042e 0.1070.0 15 Carolyn.0: Setting Hard Timer 4000
09:20:27 1013559mS CMTARGET: ac14017a0000042e 0.1070.0 15 Carolyn.0: LOOKUP CALL ROUTE: GID=0 type=100 called_party=* sub= calling=139 calling_sub= dir=out complete=0 ses=0
09:20:27 1013559mS CMTARGET: ac14017a0000042e 0.1070.0 15 Carolyn.0: ADD TARGET (N): number=* type=100 depth=1 nobar=1 setorig=1 ses=0
09:20:28 1014069mS CMExtnEvt: v=(null) State, new=Idle old=Idle,0,0,139: Digit Key Pressed 9
09:20:28 1014069mS CMExtnRx: v=139, p1=0
CMInformation
Line: type=DigitalExtn 4 Call: lid=0 id=1070 in=0
Called[9] Type=Default (100) Reason=CMDRdirect Keypad[9]
09:20:28 1014069mS CMExtnRxC: v=139
CMInformation
Line: type=DigitalExtn 4 Call: lid=0 id=1070 in=0
Called[9] Type=Default (100) Reason=CMDRdirect Keypad[9]
BChan: slot=20 chan=8
IE CMIERespondingPartyName (228)(Type=CMNameInternalUser) name=Carolyn
IE CMIERespondingPartyKName (229)(Type=CMNameDefault) name=Carolyn
IE CMIERespondingPartyNumber (230)(P:100 S:100 T:101 N:100 R:4) number=139
IE CMIEDeviceDetail (231) ac14017a0000042e LOCALE=enu HW=15 VER=11 class=CMDeviceStdPhone type=78 number=24 channel=0 features=0x10000420 rx_gain=32 tx_gain=32
ep_callid=1070 ipaddr=172.20.1.122 apps=0 loc=0 em_a_loc=1 em_d_loc=0 features2=0x20 is_spcall=0 ignores_dtmf=0 avgsid=
09:20:28 1014070mS CMTARGET: ac14017a0000042e 0.1070.0 15 Carolyn.0: Setting Hard Timer 4000
09:20:28 1014070mS CMTARGET: ac14017a0000042e 0.1070.0 15 Carolyn.0: LOOKUP CALL ROUTE: GID=0 type=100 called_party=*9 sub= calling=139 calling_sub= dir=out complete=0 ses=0
09:20:28 1014070mS CMTARGET: ac14017a0000042e 0.1070.0 15 Carolyn.0: ADD TARGET (N): number=*9 type=100 depth=1 nobar=1 setorig=1 ses=0
09:20:28 1014494mS CMExtnEvt: v=(null) State, new=Idle old=Idle,0,0,139: Digit Key Pressed 7
09:20:28 1014494mS CMExtnRx: v=139, p1=0
CMInformation
Line: type=DigitalExtn 4 Call: lid=0 id=1070 in=0
Called[7] Type=Default (100) Reason=CMDRdirect Keypad[7]
09:20:28 1014495mS CMExtnRxC: v=139
CMInformation
Line: type=DigitalExtn 4 Call: lid=0 id=1070 in=0
Called[7] Type=Default (100) Reason=CMDRdirect Keypad[7]
BChan: slot=20 chan=8
IE CMIERespondingPartyName (228)(Type=CMNameInternalUser) name=Carolyn
IE CMIERespondingPartyKName (229)(Type=CMNameDefault) name=Carolyn
IE CMIERespondingPartyNumber (230)(P:100 S:100 T:101 N:100 R:4) number=139
IE CMIEDeviceDetail (231) ac14017a0000042e LOCALE=enu HW=15 VER=11 class=CMDeviceStdPhone type=78 number=24 channel=0 features=0x10000420 rx_gain=32 tx_gain=32
ep_callid=1070 ipaddr=172.20.1.122 apps=0 loc=0 em_a_loc=1 em_d_loc=0 features2=0x20 is_spcall=0 ignores_dtmf=0 avgsid=
09:20:28 1014495mS CMTARGET: ac14017a0000042e 0.1070.0 15 Carolyn.0: Setting Hard Timer 4000
09:20:28 1014495mS CMTARGET: ac14017a0000042e 0.1070.0 15 Carolyn.0: LOOKUP CALL ROUTE: GID=0 type=100 called_party=*97 sub= calling=139 calling_sub= dir=out complete=0 ses=0
09:20:28 1014495mS CMTARGET: ac14017a0000042e 0.1070.0 15 Carolyn.0: ADD TARGET (N): number=*97 type=100 depth=1 nobar=1 setorig=1 ses=0
09:20:28 1014496mS CMTARGET: ac14017a0000042e 0.1070.0 15 Carolyn.0: SYS SC: *97 3 sc=type=Dial code=*97, num=9Y*72Y7275626705 callinfop->sending_complete=0 secondary_dialtone=
09:20:28 1014496mS CMARS: FindActiveARSByGroupID GroupID=51 - Found
09:20:28 1014496mS CMARS: MakeCallTarget - Called Number: 9
09:20:28 1014497mS CMCallEvt: 0000000000000000 0.1072.0 -1 BaseEP: NEW CMEndpoint f17b9ec8 TOTAL NOW=3 CALL_LIST=1
09:20:28 1014497mS CMTARGET: ac14017a0000042e 0.1070.0 15 Carolyn.0: CancelTimer CMTCDelayedProcessing
09:20:28 1014498mS CMTARGET: ac14017a0000042e 0.1070.0 15 Carolyn.0: INITIAL TARGETING SUCCEEDED
09:20:28 1014498mS CMTARGET: ac14017a0000042e 0.1070.0 15 Carolyn.0: GetNoAnswerTimer:15
09:20:28 1014498mS CMCallEvt: 0000000000000000 0.1071.0 15 TargetingEP: StateChange: END=B CMCSIdle->CMCSOffering
09:20:28 1014499mS CMCallEvt: 0000000000000000 0.1072.0 15 ARS for Backup: StateChange: END=T CMCSIdle->CMCSOffering
09:20:28 1014499mS CMCallEvt: 0000000000000000 0.1071.0 15 TargetingEP: RequestEnd 0000000000000000 0.1072.0 15 ARS for Backup
09:20:28 1014499mS CMTARGET: ac14017a0000042e 0.1070.0 15 Carolyn.0: CancelTimer CMTCNoAnswerTimeout
09:20:28 1014500mS CMCallEvt: 0000000000000000 0.1072.0 15 ARS for Backup: StateChange: END=B CMCSOffering->CMCSOverlapRecv
09:20:28 1014501mS CMARS: FORM: Backup - Received Number: 9
09:20:28 1014501mS CMARS: CMARSTargetingPending
09:20:28 1014501mS CMCallEvt: 0000000000000000 0.1071.0 -1 TargetingEP: StateChange: END=X CMCSOffering->CMCSDelete
09:20:28 1014501mS CMCallEvt: 0000000000000000 0.1071.0 -1 BaseEP: DELETE CMEndpoint f180e5bc TOTAL NOW=2 CALL_LIST=1

********** SysMonitor v11.0.4.0.0 build 74 [connected to 192.168.43.1 (Dr Orlick)] **********
09:20:32 1018497mS CMARS: Case 1 - dial_delay_time: 4000 has expired - Resolve what we might have - Called Number: 9 Addr: f17b9ec8
09:20:32 1018497mS CMARS: FORM: Backup - Received Number: 9
09:20:32 1018497mS CMARS: FOUND A SHORT CODE - short_code: XN; - Tel: N - Called_Party: 9 - Line Group Id: 1
09:20:32 1018497mS CMARS: SetCurrentTarget: Short_Code: XN; - Line_Group_ID: 1
09:20:32 1018497mS CMARS: FindActiveARSByGroupID GroupID=1 - Not Found
09:20:32 1018497mS CMLRQ: FindActiveLRQByGroupID GroupID=1 - Not Found
09:20:32 1018498mS ATMCMLine: [1] MakeTarget() line_group_id=1
09:20:32 1018498mS ATMCMLine: [1] ReleaseCompleteTimer(OK)
09:20:32 1018498mS CMCallEvt: 0000000000000000 0.1073.0 -1 BaseEP: NEW CMEndpoint f17e0e24 TOTAL NOW=3 CALL_LIST=1
09:20:32 1018499mS ATMCMLine: [1] MakeTarget() returned: ac14017a00000431 0.1073.0 15 Alog Trunk:1
09:20:32 1018500mS CMARS: ModifyCMARSTarget: Short_Code: XN; - Line_Group_ID: 1 set line status to CMARS_TRYING
09:20:32 1018500mS CMARS: FOUND LINE - Line Id: 1 - using line group id: 1 (code XN;, line 1) - Called Number: 9 - Calling Number: 139
09:20:32 1018500mS CMARS: SEND Setup TO LINE
09:20:32 1018500mS CMCallEvt: ac14017a00000431 0.1073.0 15 Alog Trunk:1: StateChange: END=child CMCSIdle->CMCSOffering
09:20:32 1018500mS ATMCMLine: [1] ControlEchoCancellation ON
09:20:32 1018500mS ATMCMLine: [1] CMLinkLayer Tx: 'EchoControl'
09:20:32 1018501mS CMLineTx: v=1
CMSetup
Line: type=AnalogueLine 1 Call: lid=0 id=1073 in=0
Called[9] Type=Default (100) Reason=CMDRdirect SndComp Calling[139] Type=Internal Plan=Default
BC: CMTC=3K1Audio CMTM=CallIndSigCon CMTR=64 CMST=Default CMU1=ULaw
IE CMIECallingPartyName (110)(Type=CMNameInternalUser) name=Carolyn
IE CMIECallingPartyKName (226)(Type=CMNameDefault) name=Carolyn
IE CMIERespondingPartyName (228)(Type=CMNameInternalUser) name=Carolyn
IE CMIERespondingPartyKName (229)(Type=CMNameDefault) name=Carolyn
IE CMIERespondingPartyNumber (230)(P:100 S:100 T:101 N:100 R:4) number=139
IE CMIEDeviceDetail (231) ac14017a0000042e LOCALE=enu HW=15 VER=11 class=CMDeviceStdPhone type=78 number=24 channel=0 features=0x10000420 rx_gain=32 tx_gain=32
ep_callid=1070 ipaddr=172.20.1.122 apps=0 loc=0 em_a_loc=1 em_d_loc=0 features2=0x20 is_spcall=0 ignores_dtmf=0 avgsid=
IE CMIEMohSourceId (247) MOH Source = 255
Locale: enu
09:20:32 1018501mS ATMCMLine: [1] line_group_id=1, CMLinkLayer=CmLlIdle, direction ok
09:20:32 1018501mS ATMCMLine: [1] bearer(2) compatibility ok - can make call
09:20:32 1018501mS ATMCMLine: [1] StateChange Idle->Initiated
09:20:32 1018501mS ATMCMLine: [1] CMLinkLayer Tx: 'SendingCompleteSeize'
09:20:32 1018503mS ATMChannel: [1] CMLinkLayer Rx: 'EchoControl' (ls)
09:20:32 1018503mS ATMIO: [1] ECHO CANCELLATION ON
09:20:32 1018503mS ATMChannel: [1] CMLinkLayer Rx: 'SendingCompleteSeize' (ls)
09:20:32 1018503mS ATMIO: [1] BLOCK FORWARDING ON
09:20:32 1018503mS ATMIO: [1] TRUNK SEIZE
09:20:32 1018503mS ATMChannel: [1] StateChange Idle->Seizing
09:20:32 1018546mS ATMChannel: [1] External Rx: 'Seized' (ls)
09:20:32 1018546mS ATMChannel: [1] CMLinkLayer Tx: 'SetupAck'
09:20:32 1018546mS ATMChannel: [1] CMLinkLayer Tx: 'Proceeding'
09:20:32 1018546mS ATMIO: [1] CLI DETECTION OFF, EQUALISER OFF
09:20:32 1018546mS ATMChannel: [1] StateChange Seizing->AwaitDialTone
09:20:32 1018547mS CMCallPkt: v=0
CMInformation
Line: type=AnalogueLine 1 Call: lid=0 id=1073 in=1
Tag type=Binary flags=0x1 [.$.p.!<......+.........<...../?......b.......+...!<..] [0x01 0x24 0x00 0x70 0xf5 0x21 0x3c 0xa8 0xf5 0x83 0xf8 0xa8 0xf0 0x2b 0xa0 0x84 0x00 0x00 0x00 0x03 0xf5 0xb6 0xf9 0x3c 0xf5 0x83 0xf8 0xb8 0xf0 0x]
09:20:32 1018547mS ATMCMLine: [1] CMLinkLayer Rx: 'SetupAck' callid=(lid=0, id=1073, in=1)
09:20:32 1018548mS ATMCMLine: [1] CM Tx: 'CMSetupAck' callid=(lid=0, id=1073, in=0)
09:20:32 1018548mS CMLineRx: v=1
CMSetupAck
Line: type=AnalogueLine 1 Call: lid=0 id=1073 in=0
BChan: slot=1 chan=1
IE CMIERespondingPartyNumber (230)(P:100 S:100 T:0 N:100 R:4) number=*97
IE CMIEDeviceDetail (231) ac14017a00000431 LOCALE=enu HW=15 VER=11 class=CMDeviceAlogTrunk type=0 number=1 channel=0 features=0x1 rx_gain=32 tx_gain=32
ep_callid=1073 ipaddr=172.20.1.122 apps=0 loc=0 em_a_loc=0 em_d_loc=0 features2=0x0 is_spcall=1 ignores_dtmf=0 avgsid=
09:20:32 1018548mS CMARS: LINE ep Received: CMSetupAck - child->state = CMCSOffering - ARS Call State = CMCSOverlapRecv
09:20:32 1018548mS CMARS: LINE IS NOW THE B END OF THE CALL - CMARSEndpoint::RequestEnd()
09:20:32 1018548mS CMARS: CMARSEndpoint::CallLost(cause=124) - Address: ac14017a0000042e 0.1072.0 15 ARS for Backup - Call State: CMCSOverlapRecv
09:20:32 1018548mS CMCallEvt: ac14017a0000042e 0.1072.0 -1 ARS for Backup: StateChange: END=X CMCSOverlapRecv->CMCSDelete
09:20:32 1018550mS CMCallEvt: ac14017a00000431 0.1073.0 15 Alog Trunk:1: StateChange: END=B CMCSOffering->CMCSOverlapRecv
09:20:32 1018550mS CMCallEvt: ac14017a0000042e 0.1072.0 -1 BaseEP: DELETE CMEndpoint f17b9ec8 TOTAL NOW=2 CALL_LIST=1
09:20:32 1018550mS CMCallPkt: v=0
CMInformation
Line: type=AnalogueLine 1 Call: lid=0 id=1073 in=1
Tag type=Binary flags=0x1 [.%.p.!<......+.........<...../?......b.......+...!<..] [0x01 0x25 0x00 0x70 0xf5 0x21 0x3c 0xa8 0xf5 0x83 0xf8 0xa8 0xf0 0x2b 0xa0 0x84 0x00 0x00 0x00 0x03 0xf5 0xb6 0xf9 0x3c 0xf5 0x83 0xf8 0xb8 0xf0 0x]
09:20:32 1018551mS ATMCMLine: [1] CMLinkLayer Rx: 'Proceeding' callid=(lid=0, id=1073, in=1)
09:20:32 1018551mS ATMCMLine: [1] CM Tx: 'CMProceeding' callid=(lid=0, id=1073, in=0)
09:20:32 1018551mS CMLineRx: v=1
CMProceeding
Line: type=AnalogueLine 1 Call: lid=0 id=1073 in=0
BChan: slot=1 chan=1
IE CMIEProgressIndicator (30) cs=CMCSITUT (0), loc=CMLUser (0), pd=CMPDNotISDN (1)
IE CMIERespondingPartyNumber (230)(P:100 S:100 T:0 N:100 R:4) number=*97
IE CMIEDeviceDetail (231) ac14017a00000431 LOCALE=enu HW=15 VER=11 class=CMDeviceAlogTrunk type=0 number=1 channel=0 features=0x0 rx_gain=32 tx_gain=32
ep_callid=1073 ipaddr=172.20.1.122 apps=0 loc=0 em_a_loc=0 em_d_loc=0 features2=0x0 is_spcall=1 ignores_dtmf=0 avgsid=
09:20:32 1018551mS CMCallEvt: ac14017a00000431 0.1073.0 15 Alog Trunk:1: StateChange: END=B CMCSOverlapRecv->CMCSAccept
09:20:32 1018552mS CMCallEvt: ac14017a0000042e 0.1070.0 15 Carolyn.0: StateChange: END=A CMCSDialling->CMCSDialled
09:20:32 1018552mS CMExtnEvt: v=8 State, new=Proceeding old=Dialling,0,0,Carolyn
09:20:32 1018552mS CMExtnTxC: v=139
CMProceeding
Line: type=NoLine 0 Call: lid=0 id=1070 in=0
IE CMIEProgressIndicator (30) cs=CMCSITUT (0), loc=CMLUser (0), pd=CMPDNotISDN (1)
IE CMIEProgressIndicator (30) cs=CMCSITUT (0), loc=CMLUser (0), pd=CMPDInbandPattern (8)
IE CMIERespondingPartyNumber (230)(P:100 S:100 T:0 N:100 R:4) number=*97
IE CMIEDeviceDetail (231) ac14017a00000431 LOCALE=enu HW=15 VER=11 class=CMDeviceAlogTrunk type=0 number=1 channel=0 features=0x0 rx_gain=32 tx_gain=32
ep_callid=1073 ipaddr=172.20.1.122 apps=0 loc=0 em_a_loc=0 em_d_loc=0 features2=0x0 is_spcall=1 ignores_dtmf=0 avgsid=
09:20:32 1018552mS CMExtnTx: v=139, p1=0
CMProceeding
Line: type=DigitalExtn 4 Call: lid=0 id=1070 in=0
IE CMIEProgressIndicator (30) cs=CMCSITUT (0), loc=CMLUser (0), pd=CMPDNotISDN (1)
IE CMIEProgressIndicator (30) cs=CMCSITUT (0), loc=CMLUser (0), pd=CMPDInbandPattern (8)
IE CMIERespondingPartyNumber (230)(P:100 S:100 T:0 N:100 R:4) number=*97
IE CMIEDeviceDetail (231) ac14017a00000431 LOCALE=enu HW=15 VER=11 class=CMDeviceAlogTrunk type=0 number=1 channel=0 features=0x0 rx_gain=32 tx_gain=32
ep_callid=1073 ipaddr=172.20.1.122 apps=0 loc=0 em_a_loc=0 em_d_loc=0 features2=0x0 is_spcall=1 ignores_dtmf=0 avgsid=
Timed: 06/07/20 09:20
09:20:33 1019501mS ATMCMLine: ac14017a00000431 0.1073.0 15 Alog Trunk:1 ReportTargetTimer
09:20:35 1021548mS ATMChannel: [1] Sloppy timeout(3000ms)
09:20:35 1021548mS ATMChannel: [1] StateChange AwaitDialTone->Connected
09:20:35 1021548mS ATMIO: [1] CLI DETECTION OFF, EQUALISER OFF
09:20:35 1021548mS ATMChannel: [1] CMLinkLayer Tx: 'StartDial'
09:20:35 1021549mS CMCallPkt: v=0
CMInformation
Line: type=AnalogueLine 1 Call: lid=0 id=1073 in=1
Tag type=Binary flags=0x1 [...................<.-......./.H./B../Al.!L8.........] [0x01 0x10 0x00 0x00 0x00 0x00 0x00 0x00 0xf0 0x2e 0xde 0xcc 0xf0 0x2e 0xde 0xcc 0xf5 0xb6 0xf9 0x3c 0xf0 0x2d 0x06 0x94 0xf5 0x83 0xf8 0xa8 0xf0 0x]
09:20:35 1021549mS ATMCMLine: [1] CMLinkLayer Rx: 'StartDial' callid=(lid=0, id=1073, in=1)
09:20:35 1021550mS ATMCMLine: [1] StateChange Initiated->OverlapSend
09:20:35 1021550mS ATMCMLine: [1] CMLinkLayer Tx: 'DialDigits'
09:20:35 1021551mS ATMChannel: [1] CMLinkLayer Rx: 'DialDigits' (ls)
09:20:35 1021551mS ATMIO: [1] TONE DIAL (1 digits)
09:20:35 1021551mS ATMChannel: [1] StateChange Connected->ToneDialing
09:20:35 1021728mS ATMChannel: [1] Sloppy timeout(175ms)
09:20:35 1021728mS ATMIO: [1] BLOCK FORWARDING OFF
09:20:35 1021728mS ATMChannel: [1] StateChange ToneDialing->Connected
09:20:35 1021728mS ATMIO: [1] CLI DETECTION OFF, EQUALISER OFF
09:20:35 1021728mS ATMChannel: [1] CMLinkLayer Tx: 'DigitsDone'
09:20:35 1021729mS CMCallPkt: v=0
CMInformation
Line: type=AnalogueLine 1 Call: lid=0 id=1073 in=1
Tag type=Binary flags=0x1 [...................<.-......./.H./A../Al.............] [0x01 0x19 0x00 0x00 0x00 0x00 0x00 0x00 0xf0 0x2e 0xde 0xcc 0xf0 0x2e 0xde 0xcc 0xf5 0xb6 0xf9 0x3c 0xf0 0x2d 0x06 0x94 0xf5 0x83 0xf8 0xa8 0xf0 0x]
09:20:35 1021729mS ATMCMLine: [1] CMLinkLayer Rx: 'DigitsDone' callid=(lid=0, id=1073, in=1)
09:20:35 1021729mS ATMCMLine: [1] StateChange OverlapSend->Active
09:20:35 1021730mS ATMCMLine: [1] CM Tx: 'CMProgress' callid=(lid=0, id=1073, in=0)
09:20:35 1021730mS CMLineRx: v=1
CMProgress
Line: type=AnalogueLine 1 Call: lid=0 id=1073 in=0
BChan: slot=1 chan=1
IE CMIEProgressIndicator (30) cs=CMCSITUT (0), loc=CMLUser (0), pd=CMPDNotISDN (1)
IE CMIERespondingPartyNumber (230)(P:100 S:100 T:0 N:100 R:4) number=*97
IE CMIEDeviceDetail (231) ac14017a00000431 LOCALE=enu HW=15 VER=11 class=CMDeviceAlogTrunk type=0 number=1 channel=0 features=0x0 rx_gain=32 tx_gain=32
ep_callid=1073 ipaddr=172.20.1.122 apps=0 loc=0 em_a_loc=0 em_d_loc=0 features2=0x0 is_spcall=1 ignores_dtmf=0 avgsid=
09:20:35 1021730mS CMCallEvt: ac14017a00000431 0.1073.0 15 Alog Trunk:1: StateChange: END=B CMCSAccept->CMCSRinging
09:20:35 1021730mS CMCallEvt: ac14017a0000042e 0.1070.0 15 Carolyn.0: StateChange: END=A CMCSDialled->CMCSRingBack
09:20:35 1021731mS CMExtnEvt: v=8 State, new=Alerting old=Proceeding,0,0,Carolyn
09:20:35 1021731mS CMExtnTxC: v=139
CMProgress
Line: type=NoLine 0 Call: lid=0 id=1070 in=0
IE CMIEProgressIndicator (30) cs=CMCSITUT (0), loc=CMLUser (0), pd=CMPDNotISDN (1)
IE CMIEProgressIndicator (30) cs=CMCSITUT (0), loc=CMLUser (0), pd=CMPDInbandPattern (8)
IE CMIERespondingPartyNumber (230)(P:100 S:100 T:0 N:100 R:4) number=*97
IE CMIEDeviceDetail (231) ac14017a00000431 LOCALE=enu HW=15 VER=11 class=CMDeviceAlogTrunk type=0 number=1 channel=0 features=0x0 rx_gain=32 tx_gain=32
ep_callid=1073 ipaddr=172.20.1.122 apps=0 loc=0 em_a_loc=0 em_d_loc=0 features2=0x0 is_spcall=1 ignores_dtmf=0 avgsid=
09:20:35 1021732mS CMExtnTx: v=139, p1=0
CMProgress
Line: type=DigitalExtn 4 Call: lid=0 id=1070 in=0
IE CMIEProgressIndicator (30) cs=CMCSITUT (0), loc=CMLUser (0), pd=CMPDNotISDN (1)
IE CMIEProgressIndicator (30) cs=CMCSITUT (0), loc=CMLUser (0), pd=CMPDInbandPattern (8)
IE CMIERespondingPartyNumber (230)(P:100 S:100 T:0 N:100 R:4) number=*97
IE CMIEDeviceDetail (231) ac14017a00000431 LOCALE=enu HW=15 VER=11 class=CMDeviceAlogTrunk type=0 number=1 channel=0 features=0x0 rx_gain=32 tx_gain=32
ep_callid=1073 ipaddr=172.20.1.122 apps=0 loc=0 em_a_loc=0 em_d_loc=0 features2=0x0 is_spcall=1 ignores_dtmf=0 avgsid=
Timed: 06/07/20 09:20
09:20:35 1021732mS ATMCMLine: [1] CM Tx: 'CMAlerting' callid=(lid=0, id=1073, in=0)
09:20:35 1021732mS CMLineRx: v=1
CMAlerting
Line: type=AnalogueLine 1 Call: lid=0 id=1073 in=0
BChan: slot=1 chan=1
IE CMIERespondingPartyNumber (230)(P:100 S:100 T:0 N:100 R:4) number=*97
IE CMIEDeviceDetail (231) ac14017a00000431 LOCALE=enu HW=15 VER=11 class=CMDeviceAlogTrunk type=0 number=1 channel=0 features=0x0 rx_gain=32 tx_gain=32
ep_callid=1073 ipaddr=172.20.1.122 apps=0 loc=0 em_a_loc=0 em_d_loc=0 features2=0x0 is_spcall=1 ignores_dtmf=0 avgsid=
09:20:36 1022501mS ATMCMLine: ac14017a00000431 0.1073.0 15 Alog Trunk:1 ReportTargetTimer
09:20:39 1026412mS CMExtnEvt: Jessica:143: No user activity

********** SysMonitor v11.0.4.0.0 build 74 [connected to 192.168.43.1 (Dr Orlick)] **********

********** SysMonitor v11.0.4.0.0 build 74 [connected to 192.168.43.1 (Dr Orlick)] **********
09:20:55 1041216mS CMExtnEvt: Kelly:132: No user activity
09:20:55 1041218mS CMExtnEvt: Trish:142: No user activity

********** SysMonitor v11.0.4.0.0 build 74 [connected to 192.168.43.1 (Dr Orlick)] **********
09:21:06 1053489mS ATMChannel: [1] SIT Detect Rx: 0xe000
09:21:08 1055884mS ATMChannel: [1] VoiceDetect Rx: 0xa000

********** SysMonitor v11.0.4.0.0 build 74 [connected to 192.168.43.1 (Dr Orlick)] **********

********** Warning: Logging to Screen Stopped **********