Hunt Group command 1

[quocvietvn]

Dear all,
I have MD110 that its version is "LZYR2010072/3/V99/980121/P1A".
I want to set all of extentions to Hunt Group.
Could anybody help me?

 

[cfrei]

Why?

 

[quocvietvn]

Dear cfrei,
There are 08 extensions at ELU11 Board.
I set up the NUMSE=020&&027.
I am intending to set up the incoming call to 020 if it is busy the call can re-route to 021&&&027 in turn.
Somebody told me that i have to initiate the hunt group for all extensions.Unfortunately,I did not know the command that initiate the hunt group.
Please give me your advice on this case.
Thank you so much for your helps.

 

[gcdhnjgfhfgsxh]

GHGRI :GRP=[,LIM=], SERV=, TRAF=, SEL=, QUE=[,CUST=][,RLTC=];

GRP = Group number. Directory number of internal group hunting group.
For value, consult parameter description for internal group hunting.

LIM = LIM number. The number of the LIM in which the group's data is to be placed.
If the parameter is omitted the data of the group will be placed in the LIM with the minimum number of internal group hunting group numbers.
For value, consult parameter description for internal group hunting.

SERV = Service category.
For value, consult parameter description for internal group hunting.

TRAF = Traffic category.
Traffic category of the internal group hunting group.
For value, consult parameter description for internal group hunting.

SEL = Selection category.
For value, consult parameter description for internal group hunting.

QUE = Queue length. Queue length states maximum number of queuing calls towards the group.
For value, consult parameter description for internal group hunting.

CUST = Customer number.
If the parameter is omitted the group will not be assigned to a customer number.
For value, consult parameter description for internal group hunting.

RLTC = Release link trunk category.
Category that states whether the group is assigned for Release Link Trunk functions or not.
If the parameter is omitted the group will not be assigned for Release Link Trunk functions.
For value, consult parameter description for internal group hunting

hope this helps

http://davidgarner.co.nz

 

[rfpui]

1
What means LZYR2010072/3/V99/980121/P1A ?
How to translate it to BC release?
I'm looking to my library and I can't translate LZYR.. to BC release.
At thread806-585752 is a full list of software revisions but all started from LZY 203…..


2 To quocvietv
Generally affy was send gut answer but
a. first command is GHGRI to create Hunt Group
b. second command(s) is (are) GHGMI to add extension(s) to the group.
See thread806-1200194
If You have more that 1 LIM as parameter LIM use this LIM where this ELU 11 board is placed.

3
If You want use Hunt Group You must have 9 numbers (not 8) NUMSE=020&&028
Num=020 is a Group number (Pilot number) and in command GHGMI:GRP=020…..;
Extensions have numbers 021&&028,
Now command GHGMI:GRP=020,DIR=021&&028; add' all 8 extensions to the group.

4
Some times GH is a good solution but
for example: somebody call to group 020 call is diverted to extension 021; if nobody answer telephone (021) it is ringing and at the end RELEASE.
GH have not function to rerouting to another free group member



----------------------------------
If anything can go wrong, it will.
(Murphy's Law)

 

[tczmbara]

HI
if u want to use this Group Hounting after work ours (like for production are for problems) u can use CDINI - foward calls to the external number for example for mobile. Please check commands bellow

ADCOI:ABB=xxxx,TRA=zzzzzzzzz,CLASS=0;
GHGRI:GRP=yyyy,SERV=0000,TRAF=15,SEL=11001,QUE=10,LIM=2;
GHGMI:GRP=yyyy,DIR=aaaa;
CDINIIR=yyyy,DIV=xxxx;

I hope u will understand me
sorry for my english



Best Regards

Michal

 

[tczmbara]

check too formu about: How to create an ADC group

http://www.tek-tips.com/viewthread.cfm?qid=1200194&page=1

Best Regards

Michal

 

[quocvietvn]

Dear affy1977, rfpui and tczmbaza,
Firstly, thank you so much for your guides.
Secondly, I answer your question:
When using the CADAP command,I get the information:
<CADAP;
CALENDAR DATA
IDENTITY=2-LIM-VIETNAM
VERSION=LZYR2010072/3/V99/980121/P1A
CALENDAR TIME VALID
09:32:50
12 MAR 2006
END
Does it the version of my MD110 PBX?
Thirstly, I would like to ask you some questions:
1. I only config total 08 extensions for ELU11 Board. They are:
<EXDDPIR=ALL;
EXTENSION DIRECTORY DATA
DIR CSI EQU EQUB CAT TYPE AUX EXTYPE CNUM
020 0000 002-0-40-00 - 0 EL6
021 0000 002-0-40-01 - 0 EL6 - - 0403
022 0000 002-0-40-02 - 0 EL6
023 0000 002-0-40-03 - 0 EL6
024 0000 002-0-40-04 - 0 EL6
025 0000 002-0-40-05 - 0 EL6
026 0000 002-0-40-06 - 0 EL6
027 0000 002-0-40-07 - 0 EL6

END
Could I initiate hunt group for them?
3. I always get the bellow errors:
<GHGRI:GRP=020,LIM=2,SERV=0000,TRAF=15,SEL=11001,QUE=10;
NOT ACCEPTED
SEL
UNREASONABLE VALUE
<
Perhap, I put wrong the SEL parameter.Do you guide me how I can get some parameters as SERV, TRAF, SEL? Are they the EXCCP and ROU command? If it is true please read bellow contents:
<ROCAP:ROU=ALL;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG
7 1110000 4 201000100 0 30 128 1515155 0111000100
20 0110020 4 211000000 0 5 128 1515155 1111101000
21 0110020 4 211000000 0 5 128 1515155 1111101000
70 0130020 4 211000000 0 5 128 1515155 0111100200

END
<
<EXCCP:CAT=0;
EXTENSION CATEGORY CODE
CAT TRAF SERV CDIV
0 03151515 00021200 0015
END
<
Thank you so much for your advice.
Vu Quoc Viet

 

[rfpui]

Hi
Your BC version is enigmatic for me
In My opinion it is very old system and market specific

Try to set SEL as 3 digit parameter. For example SEL=000

After send command
GHGRI:GRP=020,LIM=2,SERV=0000,TRAF=15,SEL=000,QUE=10;
Answer from system will be that grp number is not OK


----------------------------------
If anything can go wrong, it will.
(Murphy's Law)

 

[mundus]

Hi, you can't assign the group with number 020, this number is occupied by the extension 020, you must rename this number and then assign the group 020. I agree with rfpui -Your BC version is enigmatic for me !

 

[rfpui]

mundus
You have right but the first problem is BC version

----------------------------------
If anything can go wrong, it will.
(Murphy's Law)

 

[whosrdaddy]

rfpui, I think it is an older BCS system. will have to look into some books to find the version (if I still have them)

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[quocvietvn]

Dear rfui,
I agree with you about this MD110.
It is old version.But I can not change it to anther one at this moment.
However,I've done some commands as your guide.
These are the results:
<GHGRI:GRP=020,LIM=2,SERV=0000,TRAF=15,SEL=000,QUE=10;
NOT ACCEPTED
GRP
ALREADY ASSIGNED
<
<GHDAP:GRP=020;
NOT ACCEPTED
GRP
NOT ASSIGNED
<
Are there any command that helps me to do my purpose?
Thank you so much for your guide.
Vu Quoc Viet

 

[quocvietvn]

Dear rfpui,
I agree with you about this MD110.
It is old version.But I can not change it to anther one at this moment.
However,I've done some commands as your guide.
These are the results:
<GHGRI:GRP=020,LIM=2,SERV=0000,TRAF=15,SEL=000,QUE=10;
NOT ACCEPTED
GRP
ALREADY ASSIGNED
<
<GHDAP:GRP=020;
NOT ACCEPTED
GRP
NOT ASSIGNED
<
Are there any command that helps me to do my purpose?
Thank you so much for your guide.
Vu Quoc Viet

 

[gcdhnjgfhfgsxh]

Hi

Please attach the following print

GHDAP:GRP=ALL;

If the group already exists then all you will need to do is add members into the groups with the GHGMI command...

GHGMIIR=xxxx,GRP=zzzz;

Regards

Dave

http://davidgarner.co.nz/dg.aspx

 

[quocvietvn]

Dear Alls,
As malisha's guide,I renamed 020( Old DIR) to 028 then using GHGRI command.
I successfully setup a hunt group.
Unfortunately, I initiate 08 extentions to a group.
Could you guide me how I end this group to divide them to 02 groups?
I've also tried to do some commands as bellow:
- GHGME:GRP=020,DIR=021&&028;
It was executed.
- GHGRE:GRP=020;
It was responsed the "Command Unknown".
Perhap, I used the wrong command.
Please give me your advice.
Best regards
Vu Quoc Viet

 

[whosrdaddy]

in your version, deleting the last member of the group will also delete the group itself, GHGRE command doesn't exist in your version.

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[quocvietvn]

Dear all MD110 experts,
I have divided them to 02 groups.
They are running well,now.
Thank you so much for your supports.
Best regards.
Vu Quoc Viet