How to Setup Paging

[waynehamm]

I have setup the Route and Trunk port using COT, PAG, and WAT and each time I dial the number I get a fast busy tone. Here is the config for WAT

TYPE RDB
CUST 00
DMOD
ROUT 45
DES PAGING
TKTP WAT
SAT NO
RCLS EXT
DTRK NO
ISDN NO
PTYP ACO
AUTO NO
DNIS NO
ICOG OGT
SRCH LIN
STEP
ACOD 699
CPP NO
TARG 01
OABS
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
TFD 0
LEXT 100
SST 3 0
NEDC ETH
FEDC ORG
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
CDR NO
MUS NO
MANO NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
TTBL 0
OHTD NO
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO
**************************************************************
TN 003 0 00 06
TYPE WAT
CDEN 8D
CUST 0
XTRK XUT
TIMP 600
BIMP 3COM
NCOS 0
RTMB 45 1
NITE
SIGL LOP
SUPN YES
STYP PIP
CLS UNR DIP WTA LPR APN THFD
P10 NTC
TKID

 

[lmman]

Check the TGAR on the phone your testing from. If its set to 1 you will get a busy. If thats the case I would remove the TARG 1 in the RDB.

 

[GHTROUT]

Your Route has a TARG=1 so if your phone has a TGAR=1, then you will not be able to dial the Access Code.

If you solve that and still have trouble dialing subsequent digits, do this: Change "MANO" to "No" in the Route. Only do this if the first trick does not work.

~~~
[small] [©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators [/small]

 

[GHTROUT]

Ooops, definitely do what lmman said. But I posted wrong about MANO... I said Mano=No but should have said Mano=Yes. Don't change MANO unless you cannot dial zone numbers.

~~~
[small] [©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators [/small]

 

[waynehamm]

I removed the TGAR so it now looks like this. I didn't change the "MANO" since there are no Zones. Connected straight to Paging AMP that requires 600ohm connection. Still getting the fast Busy tone.

removed TGAR by LD 16
at TGAR typed x01

TYPE RDB
CUST 00
DMOD
ROUT 45
DES PAGING
TKTP WAT
SAT NO
RCLS EXT
DTRK NO
ISDN NO
PTYP ACO
AUTO NO
DNIS NO
ICOG OGT
SRCH LIN
STEP
ACOD 699
CPP NO
TARG
OABS
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
TFD 0
LEXT 100
SST 3 0
NEDC ETH
FEDC ORG
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
CDR NO
MUS NO
MANO NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
TTBL 0
OHTD NO
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO

 

[GHTROUT]

In that case, it's one of two things:

TN 3-6 (3-0-0-6) is disabled.

or

The direct connection to the paging amp is holding the line "busy". You may need a matching transformer - most applications do.

http://www.google.com/products?q=600+ohm+paging+matching+transformer

~~~
[small] [©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators [/small]

 

[SpelingChampeon]

You could try changing the TN of your trunk to DTN in the CLS. Other than that, I would suggest changing your ACOD to something other than 699, in case there is a conflict in your DN range.

 

[telebub]

What are you connecting to? A zone control unit, an amplifier, or directly to self amplified horns/speakers?

To keep you from building different types of routes over and over again for testing: if you are connecting directly to self amplified speakers or to an amplifier, then you would use a PAG route and trunk. If you are connecting to a zone control unit then you would use the WAT route and trunk.

War Eagle!
Lions Baseball '09!

 

[waynehamm]

Thank you for your posts so far.

I verified the TN is not disabled.
REQ: stat 3 6
IDLE

I Changed the CLS to DTN with no luck
I Changed ACOD to 78 and 2 with no luck

I will try a matching transformer. If I disconnect the line to the AMP should it then ring? becuase I get the same issue with the connection on the AMP or off.

 

[GHTROUT]

If you remove the TN wiring from the amp, you should get dead silence after dialing the ACCD.

The on/off status of the amp won't stop it from holding the line.

~~~
[small] [©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators [/small]

 

[waynehamm]

telebub - I'm connecting straight to a Amplifier.

GHTROUT - I have tried both with the port connected to the AMP and without it connected to anything and I'm still getting a fast busy tone.

 

[telebub]

Disable and re-enable that TN.

War Eagle!
Lions Baseball '09!

 

[telebub]

Or disable, reseat the card, then re-enable if that card doesn't have anythong else on it that is important.

War Eagle!
Lions Baseball '09!

 

[GHTROUT]

Just to make sure, you're simply dialing 699 and getting fast busy.

Are there any other trunks in that route? LD21 REQ LTM ROUT 45

Checked the CLS is the phone you're using? Any/all phones?

Try a new TN?

~~~
[small] [©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators [/small]

 

[waynehamm]

telebub - I disabled and renable the TN and Im still getting the fast busy tone. Currently unable to reseat card.


GHTROUT - I'm just dialing 699 nothing after or before. I have tried 78 and 2 as well. All of these were listed as unused. I have also tried 3 5.

Print out of route
REQ: ltm
CUST 0
ROUT 45

TYPE TLS
TKTP WAT
ROUT 45
DES PAGING
TN 003 0 00 06 MBER 1 PAGING
************************************************
Print out of Set CLS

CLS CTD FBD WTA LPR PUA MTD FNA HTA ADD HFA
MWA AAD IMD XHD IRD NID OLD VCE DRG1
POD DSX VMD CMSD CCSD SWD LNA CNDA
CFTD SFD MRD DDV CNID
ICDD CDMD MCTD CLBD AUTU
GPUD DPUD DNDD CFXD ARHD FITD CLTD ASCD
CPFA CPTA ABDD CFHD FICD NAID
DDGA NAMA
USRD ULAD RTDD OCBD FLXD

Here is another Route and Trunk Created using different TN
TYPE RDB
CUST 00
DMOD
ROUT 44
DES PAGING
TKTP WAT
SAT NO
RCLS EXT
DTRK NO
ISDN NO
PTYP ACO
AUTO NO
DNIS NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 78
CPP NO
TARG
BILN NO
OABS
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
TFD 0
LEXT 100
SST 3 0
NEDC ETH
FEDC ORG
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
DRNG NO
CDR NO
MUS NO
MANO NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
TTBL 0
OHTD NO
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO
************************
TN 003 0 00 05
TYPE WAT
CDEN 8D
CUST 0
XTRK XUT
TIMP 600
BIMP 3COM
NCOS 0
RTMB 44 1
NITE
SIGL LOP
SUPN NO
CLS UNR DTN WTA LPR APN THFD
P10 NTC
TKID

And route 44 member check
TYPE TLS
TKTP WAT
ROUT 44
DES PAGING
TN 003 0 00 05 MBER 1 PAGING

 

[telebub]

Here is your original post of the TN. Is it still this way? If so, change SUPN to NO and CLS to DTN.


TN 003 0 00 06
TYPE WAT
CDEN 8D
CUST 0
XTRK XUT
TIMP 600
BIMP 3COM
NCOS 0
RTMB 45 1
NITE
SIGL LOP
SUPN YES <---Change to NO
STYP PIP
CLS UNR DIP WTA LPR APN THFD <---Change to DTN
P10 NTC
TKID


War Eagle!
Lions Baseball '09!

 

[tnphoneman]

Also uf there are no zones in this paging scenario then create the trunk as a PAG not a WAT.

Signature===========================================

http://www.greatwhitetechnologies.com

Aastra Authorized Reseller

 

[GHTROUT]

I would be interested in knowing if you can dial _any_ Route Access Codes.

~~~
[small] [&copy;] GHTROUT.com [&hArr;] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators [/small]

 

[tnphoneman]

What is the CLS on the set? UNR/CTD/SRE etc?

Signature===========================================

http://www.greatwhitetechnologies.com

Aastra Authorized Reseller

 

[telebub]

He posted above a CLS of CTD for the set. He should change it to UNR and try it.

War Eagle!
Lions Baseball '09!