How to route "733" calls to a specific tie trunk loop? 2

[richb808]

Hi guys,

I would like to allow user to dial "733" and then have it route the call to a specific PRI tie trunk loop.
How would I go about doing that please?

Here's my system info:
>LD 22
REQ ISS
VERSION 2921
RELEASE 4
ISSUE 00 T +
IDLE_SET_DISPLAY NORTEL

Thanks!
Rich

 

[janaya]

What route is that PRI?

login as: admin
SSH server: User Authentication
Using keyboard-interactive authentication.
admin, welcome to Avaya CS1K Call Server
Password:
SSH server: Login Success!
Using keyboard-interactive authentication.


The software and data stored on this system are the property of,
or licensed to, Avaya Inc. and are lawfully available only to
authorized users for approved purposes. Unauthorized access to
any software or data on this system is strictly prohibited and
punishable under appropriate laws. If you are not an authorized
user then logout immediately. This system may be monitored for
operational purposes at any time.

.
TTY #15 LOGGED IN ADMIN 14:48 8/4/2016

>ld 86
ESN000

MEM AVAIL: (U/P): 87578336 USED U P: 14214960 1859053 TOT: 103652349
DISK SPACE NEEDED: 3401 KBYTES
REQ new <-- you type this
CUST 0 <-- you type this
FEAT rlb <-- you type this
RLI 555 <-- you put your new RLI number here.
ELC
ENTR 0 <-- you type this
LTER
ROUT 10 <-- this is the route for your PRI.
FRL <-- put the Minimum NCOS to access the route here. If you want to allow all just enter through here
MFRL
OVLL

***NOTE*** I just entered through the prompts that I don't think you will need. Pay attention to the ones where I commented


MEM AVAIL: (U/P): 87578087 USED U P: 14215184 1859078 TOT: 103652349
DISK SPACE NEEDED: 3401 KBYTES
REQ

Now the rest has more to do with how you are dialing. Do you want the calls to route 9+773, or just when they dial 773. One way is done through LD 90 (9+ dialing), the other is done via LD 87 (DSC,TSC dialing)

Let me know how you want this done and I will let you know how to program.



John Anaya
Amdocs Inc.
ACSS/ACIS - CS1000 Rls 7.5/Call Pilot 5
ACSS/ACIS - SME - IP Office 8.0
APSS/APDS - Avaya UC Services

Public Profile

http://www.linkedin.com/pub/john-anaya/25/1b9/a9b/

 

[richb808]

Hi John,

The PRI is route 9

TYPE TLST
TKTP TIE
ROUT 9
DES TEST
TN 027 01 MBER 1 TEST
TN 027 02 MBER 2 TEST
...
TN 027 23 MBER 23 TEST

I would like them to just dial only "733" no 9 prefix please.

Thanks!
Rich

 

[KCFLHRC]

If you dont want them to dial the "9" prefix then you will have to set it up as a CDP entry.

 

[richb808]

Hi KCFLHRC,
What are the steps for setting that up?
Thanks,
Rich

 

[richb808]

Hi John/KCFLHRC,

I was able to figure it out!

REQ new
CUST 0
FEAT cdp
TYPE dsc
DSC 733
FLEN 3
DSP LSC
RLI 3
NPA
NXX
DSC

RLI 3 points to ROUTE 9 and it works great!

Thanks much for all super helpful advice!
Rich

 

[KCFLHRC]

Wonderful