HOW TO REPLACE THE 4 DIGIT TO 5 DIGIT & DEST FROM 0 TO 9?

[ALTAMIMI]

I HAVE 1000 ANALOG EXTENITON AND 900 DIGITAL EXTENITON EVRY EXTENITON HAVE 4 DIGIT TO 5 DIGIT AND ALL THESE EXTENITON MAKE E1 TLU76\3?
HOW THE ESYE WAY TO CHANGE ALL EXTENITONS AND THE DIGITAL EXTENITON HAVE FUNCTION KEY'S

 

[doktor]

You can use the NUTRI command to convert from 4 to 5 digits, or end all numbers (EXTEE/KSEXE) and initiate them al again by EXTEI/KSEXI.

///doktor

 

[ALTAMIMI]

thanks Mr. doktor

how abut PC-REGEN i take from MD110(TSWSP4).
i thenk i can replace from some command but i do not know wich file i have to change?

 

[doktor]

Hi ALTAMIMI

We use a very good text editor called TextPad.
You can take you re-generated INI files, like e.g. EXTEI, and add the 5 digit by marking it in TextPad "block mode".
The marked area can be changed, deleted or digigts could be added.
E.g.
EXTEI;DIR=5644,CAT=15,EQU=1-1-22-11,TYPE=EL6;
If 7 should be added "75644", the area in the text file just before the digit 5 is marked - top to buttom of the file - and the digit 7 is added to all lines.
Easy and fast!

///doktor

 

[DUFQI]

If you are using a new numberrange just use KSDNC and EXDNC

 

[doktor]

Take care using " KSDNC and EXDNC ". You MD may reload if you have high traffic.

///doktor

 

[ALTAMIMI]

THANKS FOR ALL

ABUT "EXDNC" AND "KSDNC" I CAN NOT USE IF THE EXTENTION HAVE PARALLEL RINGING.
I MAKE RE-GENERATED FORM PC-REGEN I WILL TRAY FROM THERE

I CHANG IN "KSEXI" AND "EXTEI"BUT WICH COMMAND I HAVE TO CHANGE ELSE

 

[doktor]

You need to change also your groups GHDAP:GRP=ALL; and ACD groups.
If you check your number analysis (NADAP you will see all active (existing) numbers.

///doktor

 

[whosrdaddy]

Altmamimi,

first of all don't use CAPS in your post, it is considered as shouting. About your question: yes it's best to use PC-REGEN to create a new system.

so steps to be taken:

1) take a full PC-REGEN printout from your PBX (this file can be generated from PC-REGEN) and must be sent with winfiol. Regenerate initiate commands from printout files using PC-REGEN.
2) edit all files, changing all the required extension numbers
3) start a new system from INL, load license and send LIM disposition file.
4) send initiate command files to PBX with winfiol

If you have not fully understood what I'm trying to explain here, then don't do it, you must have full knowledge of the MD110 to achieve this task. Do you have a local service provider? They should be able to do this work for you.

Cheers,
Daddy

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[ALTAMIMI]

thanks to all

i chang all extentions from file "KS" and "EX"
this is "NADAP" for my system

<NADAP;
NUMBER ANALYSIS DATA
TYPE OF SERIES NUMBER SERIES
EXTENSION NUMBER SERIES 1000 - 1030
1032 - 1050
2000 - 2887
28889
2889 - 3832
3900 - 3910
3999
4400 - 4900
6666
EXTERNAL DESTINATION CODE 0
60 - 63
700 - 709
8
OPERATOR INDIV. NUMBER SERIES 5001 - 5007
OPERATOR COMMON NUMBER SERIES 9
OPERATOR COM. DID. NUM. SERIES 9
ABBREVIATED COMMON NUMBER SERIES 4000 - 4398
COMMON PUBLIC DIRECTORY NUMBER 28888
DIRECT INWARD SERVICE ACCESS 1031
TYPE OF SERVICE CODE SERVICE CODE
ANSWER ON CALL TO COMMON BELL 55
EXTERNAL NUMBER LENGTH DATA
EXTERNAL NUMBER NUMBER LENGTH
019 4 - 9
02 4 - 8
04 4 - 8
63 9 - 20
PROCEED TO SEND SIGNAL DATA
EXTERNAL NUMBER POS. TYPE
CALL DISCRIMINATION DATA
EXTERNAL/INTERNAL NUMBER CAT
011 8 5 3
01700 5 3
019 8 5 3
02 10 9 8 6 5 3 2
03 5 3
04 10 9 8 6 5 3 2
08 10 9 6 5 3 2
0902 10 9 8 5 3 2
0903 10 9 5 3 2
0904 10 9 8 5 3 2
0905 10 9 8 5 3 2
0906 10 9 5 3 2
0907 10 9 8 5 3 2
0908 10 9 5 3 2
0909 10 9 8 5 3
0919 5 3
0920 10 9 6 5 3 2
0930 5 3
0939 8 6 5 4 3 2
0940 10 9 8 6 5 3 2
0961 8 5 3 2
0963 5 3
0992 10 9 8 6 5 4 3 2
0993 10 9 5 3 2
0996 10 9 5 3 2
0997 10 9 5 3 2
0998 10 9 5 3 2
0999 10 9 5 3 2
1 10 9 8 6 5 4 3 2
1
2 10 9 8 6 5 4 3 2
1
3 10 9 8 6 5 4 3 2
1
4 10 9 8 6 5 4 3 2
1
60 8 5
61 9
62 10
63 9 8 7 6 5 4 3 2
6666 10 9 8 7 6 5 4 3
2 1 0
701 5
705 11
706 10 4 3 2 1
8 10 9 8 6 5
9 10 9 8 6 5 3 2 1
0
END

how to change "0" to "9" for all system frme PC-REGEN?

aftare i change evry thing i will make REL for system

 

[whosrdaddy]

you need to change the number for your operator.

as you can see in nadap, operater nr is now 9 (OC and OD).

so assign it another nr, then you can put 9 in ED range and program RODDI.

/Daddy

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[ALTAMIMI]

HI EVRY BODY
THIS COMMAND I TAKE IT FROM PC-REGEN
WICH COMAND FROM THIS I HAVE TO CHANG THE DEST FROM 0 TO 9?
GSMULT
CNBOI
CNBRI
IOBPI
IONPC
IOEQI
IOIFC
IOFDC
ALEOI
ALDAS
ALULS
IOCAC
SYDAS
SYTDS
ASPAC
TCMAS
NUMANAL
NUTRI
OPERI
OPISS
EXCCS
GESPI
ADCOI
ROCAI
RODAI
RODDI
GEDII
IPBOI
IPEXI
IPGKC
EXTEI
KSEXI
KSANI
KSMDI
KSFKC
GHGRI
GHGMI
ACPAC
ROEQI
OPCTS
OPCGS
OPADC
OPRSC
OPDNC
CPDNI
RODNI
LCTDI
CLCCC
AUCOI
KSTSC
KSCHC
GETSC
CXSYC
SPEXI
CDINI
CASII
CHCMI
GEFKI

 

[Monrovia]

Note: If you dont have some expertise in reading & executing commands, dont try these steps. These steps will make your operator & outgoing calls Dead.

Using WINFIOL

NANSE:NUMSE=9,NUMTYP=OC;
NANSE:NUMSE=9,NUMTYP=OI;
you end the Operator Common no & Operator Individual no.

NANSI:NUMSE=5000,NUMTYP=OC;
NANSI:NUMSE=5000,NUMTYP=OI;
You initiate OC & OI as 5000, which is free in your number series.(1,2,3,4,5XXX,6,7,8&9 already in use)Once you converted your Dest 0 to 9, you may make operator as 0 which may be free to use at that time.(for the time being there will be no calls to operator) So take care, your Operator parameters has to be set accordingly.

NANSI:NUMSE=9,NUMTYP=ED;
you initiate ED in number series

now initiate the route parameters, for which need your RO details, roodp, rocap, roeqp, rodap, rodnp, etc

 

[ALTAMIMI]

THAKS ALL
I WILL TRY IT AND TELL YOU WHAT HAPEN.