How to make name display from dial extension for cisco ip phone to simens hipath 4k v 6.0

[viswa1969]

Dear sir,

we have hipath 4k version 6 works with Cisco 3900 series call manager with sip trunking.
we are communicate well, for someone has dial from cisco ip phone to siemens opti 500 device,But our facing problem is end user dialling from caller
name not appear in opti 500 standrad caller id phone.

Please help me some one.

 

[sbcsu]

Name transfer is limited.
There is a pdf but it is for earlier versions but should give some assistance

https://hipath.tonidoid.com

Click on Guest Login
Username:hipath4000
Password:hipath4000

Docs/Cisco

 

[viswa1969]

Dear Sbcsu,
I have send our system board module details ,B channel details,line status details given below;
so again I would like to ask our hipath 4k version v6 to cisco3900 series, receiving call name appear how to make display end user phone(optiset E Standard)hicom4k side.please give me a related command parameter,which parameter i should chenge - please give me a solution, i am patient now, help me dear sbcsu.
<dis-bcsu
TYPE = tbl
LTG = 1
LTU = 4
SLOT = 61;
DIS-BCSU:TBL,1,4,61;
H500: AMO BCSU STARTED

LTG 1 LTU 4 SRCGRP 1 ALARMNO-LTU 0
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
| | | |S|H|AL-| | | |
| ASSIGNED | MODULE |FCT|E|W|ARM| | INSERTED | HW- | MODULE
PEN | MODULE | TYPE |ID |C|Y|NO | | MODULE |STATE INFO | STATUS
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
61 | Q2226-X200 DIUT2-E1 1 A 0| | Q2226-X200 | 1 -06 - | READY

dis-tdcsu
PEN1 = 1-4-61-0;
DIS-TDCSU:1-4-61-0;
H500: AMO TDCSU STARTED
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2CONN PEN = 1-04-061-0 TGRP = 40 |
|---------------------------------------------------------------------------|
| PROTVAR = ECMAV2 INS = Y SRCHMODE = ASC |
| COTNO = 20 COPNO = 20 DPLN = 0 |
| ITR = 0 COS = 44 LCOSV = 32 |
| LCOSD = 1 CCT = DESTNO = 2 |
| SEGMENT = 8 DEDSCC = DEDSVC = NONE |
| FACILITY = DITIDX = SRTIDX = |
| TRTBL = GDTR SIDANI = N ATNTYP = TIE |
| CBMATTR = NONE NWMUXTIM = 10 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNIP = ISDNNP = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 10 SATCOUNT = MANY NNO = 1 -1 -400 |
| ALARMNO = 0 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 20 FWDX = 5 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = CCHDL = |
| UUSCCX = 16 UUSCCY = 8 FNIDX = 1 |
| CLASSMRK = EC & G711 & G729AOPT SRCGRP = ( ) |
| TCCID = SECLEVEL = TRADITIO |
| HMUSIC = 0 |
|---------------------------------------------------------------------------|
| BCNEG = Y BCGR = 1 LWPAR = 1 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| DMCALLWD = VNNO = |
| SVCDOM = |
| BCHAN = 1 && 30 |
| |
+---------------------------------------------------------------------------+
AMOUNT OF B-CHANNELS IN THIS DISPLAY-OUTPUT: 30

AMO-TDCSU-111 DIGITAL TRUNKS
DISPLAY COMPLETED;
<DIS-TDCSU:1-4-61-1;
DIS-TDCSU:1-4-61-1;
H500: AMO TDCSU STARTED
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2CONN PEN = 1-04-061-1 TGRP = 41 |
|---------------------------------------------------------------------------|
| PROTVAR = ECMAV2 INS = N SRCHMODE = ASC |
| COTNO = 20 COPNO = 20 DPLN = 0 |
| ITR = 0 COS = 44 LCOSV = 32 |
| LCOSD = 1 CCT = DESTNO = 2 |
| SEGMENT = 8 DEDSCC = DEDSVC = NONE |
| FACILITY = DITIDX = SRTIDX = |
| TRTBL = GDTR SIDANI = N ATNTYP = TIE |
| CBMATTR = NONE NWMUXTIM = 10 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNIP = ISDNNP = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 10 SATCOUNT = MANY NNO = 1 -1 -400 |
| ALARMNO = 0 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 20 FWDX = 5 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = CCHDL = |
| UUSCCX = 16 UUSCCY = 8 FNIDX = 1 |
| CLASSMRK = EC & G711 & G729AOPT SRCGRP = ( ) |
| TCCID = SECLEVEL = TRADITIO |
| HMUSIC = 0 |
|---------------------------------------------------------------------------|
| BCNEG = Y BCGR = 1 LWPAR = 1 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| DMCALLWD = VNNO = |
| SVCDOM = |
| BCHAN = 1 && 2 |
| |
+---------------------------------------------------------------------------+
AMOUNT OF B-CHANNELS IN THIS DISPLAY-OUTPUT: 2

AMO-TDCSU-111 DIGITAL TRUNKS
DISPLAY COMPLETED;
<DIS-SDSU:ALL,,PEN,PER3,1,1,67;
DIS-SDSU:ALL,,PEN,PER3,1,1,67;
H500: AMO SDSU STARTED

LTG1 (PERIPHERY)
------
MOUNTING LOCATION MODULE NAME BDL BD(#=ACT) STATUS
------------------- LTG 1 --------------------- READY
-LTUW---------SG 1 LTU 1 --------------------- READY
** .LTG 1.LTU 1.067 SLMA24 A Q2246-X READY
CCT LINE STNO SI BUS TYPE
000 1622 6666 VCE READY
ELEM DEV. . . . . . ANALOG TERM READY
(ALT_ROUT: N) (ANATE )
CCT LINE STNO SI BUS TYPE
001 1623 6667 VCE READY
ELEM DEV. . . . . . ANALOG TERM READY
(ALT_ROUT: N) (ANATE )
CCT LINE STNO SI BUS TYPE
002 1624 6668 VCE READY
ELEM DEV. . . . . . ANALOG TERM READY
(ALT_ROUT: N) (ANATE )
CCT LINE STNO SI BUS TYPE
003 1625 6669 VCE READY
ELEM DEV. . . . . . ANALOG TERM READY
(ALT_ROUT: N) (ANATE )
CCT LINE STNO SI BUS TYPE
004 1626 6670 VCE READY
ELEM DEV. . . . . . ANALOG TERM READY
(ALT_ROUT: N) (ANATE )
CCT LINE STNO SI BUS TYPE
005 1627 6671 VCE READY
ELEM DEV. . . . . . ANALOG TERM READY
(ALT_ROUT: N) (ANATE )
CCT LINE STNO SI BUS TYPE
006 1628 6672 VCE READY
ELEM DEV. . . . . . ANALOG TERM READY
(ALT_ROUT: N) (ANATE )
CCT LINE STNO SI BUS TYPE
007 1629 6673 VCE READY
ELEM DEV. . . . . . ANALOG TERM READY
(ALT_ROUT: N) (ANATE )
CCT LINE STNO SI BUS TYPE
008 1630 6674 VCE READY
ELEM DEV. . . . . . ANALOG TERM READY
(ALT_ROUT: N) (ANATE )
CCT LINE STNO SI BUS TYPE
009 1631 6675 VCE READY
ELEM DEV. . . . . . ANALOG TERM READY
(ALT_ROUT: N) (ANATE )
CCT LINE STNO SI BUS TYPE
010 1632 6676 VCE READY
ELEM DEV. . . . . . ANALOG TERM READY
(ALT_ROUT: N) (ANATE )
CCT LINE STNO SI BUS TYPE
011 1633 NOGEN
012 1634 7901 VCE READY
ELEM DEV. . . . . . ANALOG TERM READY
(ALT_ROUT: N) (ANATE )
CCT LINE STNO SI BUS TYPE
013 1635 7097 VCE READY
ELEM DEV. . . . . . ANALOG TERM READY
(ALT_ROUT: N) (ANATE )
CCT LINE STNO SI BUS TYPE
014 1636 2222 VCE READY
ELEM DEV. . . . . . ANALOG TERM READY
(ALT_ROUT: N) (ANATE )
CCT LINE STNO SI BUS TYPE
015 1637 NOGEN
016 1638 4444 VCE READY
ELEM DEV. . . . . . ANALOG TERM READY
(ALT_ROUT: N) (ANATE )
CCT LINE STNO SI BUS TYPE
017 1639 5555 VCE READY
ELEM DEV. . . . . . ANALOG TERM READY
(ALT_ROUT: N) (ANATE )
CCT LINE STNO SI BUS TYPE
018 1640 7032 VCE READY
ELEM DEV. . . . . . ANALOG TERM READY
(ALT_ROUT: N) (ANATE )
CCT LINE STNO SI BUS TYPE
019 1641 NOGEN
020 1642 7227 VCE READY
ELEM DEV. . . . . . ANALOG TERM READY
(ALT_ROUT: N) (ANATE )
CCT LINE STNO SI BUS TYPE
021 1643 7008 VCE READY
ELEM DEV. . . . . . ANALOG TERM READY
(ALT_ROUT: N) (ANATE )
CCT LINE STNO SI BUS TYPE
022 1644 2000 VCE READY
ELEM DEV. . . . . . ANALOG TERM READY
(ALT_ROUT: N) (ANATE )
CCT LINE STNO SI BUS TYPE
023 1645 1900 VCE READY
ELEM DEV. . . . . . ANALOG TERM READY
(ALT_ROUT: N) (ANATE )

AMO-SDSU -111 STATUS DISPLAY IN SWITCHING UNIT
DISPLAY COMPLETED;

 

[sbcsu]

REG-COT:20;
REG-COP:20;

 

[viswa1969]

Dear Sir,

Thanks for your support and I have to this command and successful, result feed back give to you.

Best regards.

 

[viswa1969]

Dear sir,

we have to follow the your commands reg-cot, reg- cop already available. still the same problem going on the hipath 4k v.6.0
so I have given the details for parameter below check and for your review:

dis-tdcsu
PEN1 = 1-4-61-0;
DIS-TDCSU:1-4-61-0;
H500: AMO TDCSU STARTED
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2CONN PEN = 1-04-061-0 TGRP = 40 |
|---------------------------------------------------------------------------|
| PROTVAR = ECMAV2 INS = Y SRCHMODE = ASC |
| COTN O = 20 COPNO = 20 DPLN = 0 |
| ITR = 0 COS = 44 LCOSV = 32 |
| LCOSD = 1 CCT = DESTNO = 2 |
| SEGMENT = 8 DEDSCC = DEDSVC = NONE |
| FACILITY = DITIDX = SRTIDX = |
| TRTBL = GDTR SIDANI = N ATNTYP = TIE |
| CBMATTR = NONE NWMUXTIM = 10 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNIP = ISDNNP = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 10 SATCOUNT = MANY NNO = 1 -1 -400 |
| ALARMNO = 0 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 20 FWDX = 5 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = CCHDL = |
| UUSCCX = 16 UUSCCY = 8 FNIDX = 1 |
| CLASSMRK = EC & G711 & G729AOPT SRCGRP = ( ) |
| TCCID = SECLEVEL = TRADITIO |
| HMUSIC = 0 |
|---------------------------------------------------------------------------|
| BCNEG = Y BCGR = 1 LWPAR = 1 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| DMCALLWD = VNNO = |
| SVCDOM = |
| BCHAN = 1 && 30 |
| |
+---------------------------------------------------------------------------+
AMOUNT OF B-CHANNELS IN THIS DISPLAY-OUTPUT: 30

dis-cossu
TYPE = cos
COS = 44;
DIS-COSSU:COS,44;
H500: AMO COSSU STARTED
+------+-----------------+---------------+-----------------+
| COS | VOICE | FAX | DTE |
+------+-----------------+---------------+-----------------+
| 44 |>COSFORNORMALUSERS |
| | TA | NOCO | NOCO |
| | TSUID
| | TNOTCR | FAX | |
| | CDRSTN | | |
| | CDRC | | |
| | CDRIND | | |
| | CDRINT | | |
| | COSXCD | | |
| | MB | | |
| | OFHKRC | | |
| | CFNR | | |
| | MSN | | |
| | OVCAT | | |
| | CFB | | |
| | FWDBAS | | |
| | FWDECA | | |
| | FWDEXT | | |
| | CW | | |
| | SUTVA | | |
| | ACTMAN | | |
+------+-----------------+---------------+-----------------+

AMO-COSSU-111 CLASSES OF SERVICE
DISPLAY COMPLETED;
For example our system internal extension change some parameter but haven't display for siemens opti 500 caller id phone external call from cisco 3900 series.
cha-sbcsu
STNO = 1995
NEWNO =
COS1 =
COS2 =
LCOSV1 =
LCOSV2 =
LCOSD1 =
LCOSD2 =
DPLN =
ITR =
SSTNO =
COSX =
SPDI =
SPDC1 =
SPDC2 =
TRACE =
ALARMNO =
RCBKB =
RCBKNA =
CBKBMAX =
HMUSIC =
OFFTYPE =
BASICSVC =
OPT = opti
IDCR =
REP =
SECR =
SPROT =
FPROT =
DPROT =
DSSTNA =
DSSTNB =
DIGNODIS =
SOPTIDX =
FOPTIDX =
DOPTIDX =
OPTICA =
OPTIDA =
ASYNCT =
OPTICOM =
PATTERN =
VPI =
VCI =
HEADSET =
HSKEY =
DFSVCANA =
CBKNAMB =
TEXTSEL =
CALLOG =
PMIDX =
COMGRP =
APICLASS =
SECAPPL =
DNIDSP = yes;
CHA-SBCSU:1995,,,,,,,,,,,,,,,,,,,,,,,OPTI,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,YES;
H500: AMO SBCSU STARTED
H07: 1995 STATION DATA CHANGED

AMO-SBCSU-111 STATION AND S0-BUS CONFIGURATION OF SWITCHING UNIT
CHANGE COMPLETED;
What's my side problem in our system from cisco ip phone ?
so could you bring some an example commands.

Thanks.

 

[sbcsu]

REG-COT:20;
REG-COP:20;
Does not do anything - it only shows you the COT and COP 20

Please paste the results here...

 

[viswa1969]

Dear Sir,

I have read with your mail and find given below the details for REG-COT:20;
REG-COP:20;REG-COS:44;

<reg-cot
COTNO = 20;
REG-COT:20;
H500: AMO COT STARTED
ADD-COT: 20,XFER&ANS&MFC&KNOR&CEBC&COTN&BSHT&DPRE&
LWNC&ICZL&ICZO&CDRD&NTON;

AMO-COT -111 CLASS OF TRUNK FOR CALL PROCESSING
REGENERATE COMPLETED;
<reg-cop
COPNO = 20;
REG-COP:20;
H500: AMO COP STARTED
ADD-COP:20,,TA,TA;

AMO-COP -111 CLASS OF PARAMETER FOR DEVICE HANDLER
REGENERATE COMPLETED;
<reg-cossu
TYPE = cos
COS = 44;
REG-COSSU:COS,44;
H500: AMO COSSU STARTED
ADD-COSSU:,44,,,,,,,,"COSFORNORMALUSERS";
CHA-COSSU:COS,44,TA&TSUID&TNOTCR&CDRSTN&CDRC&CDRIND&CDRINT&COSXCD;
CHA-COSSU:COS,44,MB&OFHKRC&CFNR&MSN&OVCAT&CFB&FWDBAS&FWDECA;
CHA-COSSU:COS,44,FWDEXT&CW&SUTVA&ACTMAN;
CHA-COSSU:COS,44,,NOCO&NOTIE&FAX;
CHA-COSSU:COS,44,,,NOCO&NOTIE;

AMO-COSSU-111 CLASSES OF SERVICE
REGENERATE COMPLETED;

Could you please check the parameter and give the result.

Thanks.

 

[sbcsu]

ADD-COT:21,PRI&RCL&XFER&ANS&CHRT&KNOR&CEBC&CBBN&CBFN&BSHT&ROPT&TSCS&ICZL&AOCC&LINO&AMFC&CTLS&DFNN&NTON;
CHANGE-COT:21,COTADD,,INDEP,"CISCO LINK";

ADD-COP:21,EOF&SFRM&CCR&L3AR&RMSG&RRST&DTM1,TA,TA;
CHANGE-COP:21,COPADD,,,,INDEP,"CISCO LINK";

CHANGE-TDCSUEN=1-4-61-0,COTNO=21,COPNO=21,COTX=21;

Re Test

 

[viswa1969]

Dear Sir,

First of all thank your support,

And i have change parameter follow above and retest then reply for you.

Best regards.

 

[viswa1969]

Dear Sir,

I have to follow your step the command to execute,still not yet showing name from receiving call.
And I have given the details,could you please check what's a problem our side.

ADD-COP:21,EOD&SFRM&CCR&L3AR&RMSG&RRST&DTM1,TA,TA;
ADD-COP:21,EOD&SFRM&CCR&L3AR&RMSG&RRST&DTM1,TA,TA;
H500: AMO COP STARTED
H01: COP 21 ASSIGNED

AMO-COP -111 CLASS OF PARAMETER FOR DEVICE HANDLER
ADD COMPLETED;
<CHANGE-COP:21,COPADD,,,,INDEP,"CISCO LINK";
CHANGE-COP:21,COPADD,,,,INDEP,"CISCO LINK";
H500: AMO COP STARTED
H06: COP 21 CHANGED

AMO-COP -111 CLASS OF PARAMETER FOR DEVICE HANDLER
CHANGE COMPLETED;
<cha-tdcsu
PEN = 1-4-61-0
COTNO = 21
COPNO = 21;
CHA-TDCSU:1-4-61-0,21,21;
H500: AMO TDCSU STARTED
H03: BCGR 1 AT PEN 1-04-061-0 CHANGED

AMO-TDCSU-111 DIGITAL TRUNKS
CHANGE COMPLETED;
<rest-bssu
ADDRTYPE = pen
LTG = 1
LTU = 4
SLOT = 61
WTIME =
REFOFF = ;
REST-BSSUEN,1,4,61,,;
H500: AMO BSSU STARTED
H23: MODULE 1-4-61 DEACTIVATED, ACTIVATION STARTED
H02: MODULE 1-4-61 ACTIVATED

AMO-BSSU -111 BOARD SWITCH, SWITCHING UNIT
RESTART COMPLETED;

Thanks.

 

[viswa1969]

Dear sbcsu,

I have send all are excuete commands(parameter) details above,could you please check and for your review.

I will wait for your support,

Thank you sir.

 

[sbcsu]

CHANGE-TDCSUEN=1-4-61-0,COTNO=21,COPNO=21,COTX=21;

You can download the PDF in the Tonido site
That's all the info I have.
If it is not working then it is back to tracing and working with Cisco persons.

 

[viswa1969]

Dear Sir,
I have already tried to CHANGE-TDCSUEN=1-4-61-0,COTNO=21,COPNO=21,COTX=21; and resart the pen.
And I have been check to java-(REAL TIME DIAGNOSTIC SYSTEM) put in ISDN PEN and start trace and give attach file .
Could you please check and for your review tell me which side problem in that tracer file.
I would you appreciate your help very much.

Thank you sir.

 

[viswa1969]

Dear sbcsu

could you please check above the attach file for tracer details.

Thanks once again for your help to me.

 

[viswa1969]

Dear sbcsu

Kindly need for your help and your technical support.

Thanks...

 

[sbcsu]

Hi,
It looks to me that the Cisco is getting the name EPABX Room, however the cisco is not sending any name ?
Can you do more test calls and explain what is happening again.
Thank you