How to linking 2 System NEC SV9100 With ISDN Card GCD PRI 1

[Sinjisn]

Dear all,
We have
Site A: EXT 1XX, 2XX + GCD PRI
Site B: EXT 3XX, 4XX + GCD PRI
How to linking 2 System NEC SV9100 With ISDN Card GCD PRI, and EXT site A can access CO trunk site B?
Thank all!

 

[CoralTech]

Set PRI trunk type to TIE. Adjust numbering plan and F-Route tables accordingly.

 

[Sinjisn]

Thank Coral Tech!
Please help me in case 2 sysem SL2100 + PRTA card, don't like SV9100.
I appreciate your support!

 

[CoralTech]

Same.

 

[Sinjisn]

Site A: EXT 1XX, 2XX + PRTA (Trunk Group 7)
Site B: EXT 3XX, 4XX + PRTA (Trunk Group 7)
---------------------------------------------------------------
Set up for site A
10-03-01: Select T-Point
11-01: Adjust numbering plan (1XX, 2XX type Extension Access, 3XX, 4XX type F-route Access)
11-02: Extension Number
14-05: Adjust Trunk group for PRI card (Ex TrG 7)
21-13: ISDN Calling Party Number Setup for Extension
22-02: Set PRI trunk type to TIE line
22-09-01: Dial-In Receive Digit set 3 (for TrG 7)
22-11-01 and 22-11-02: Ex Receive number 100 then Target 100
44-02: F-route Dial Analysis table, Table Entry = 1,2, when dial 3,4 then service type is F-route table, additonal data set 1
44-05-01: F-route table 1, 2. Trunk Group priority Number 1 set 7
----------------------------------------------------------------
Set up for site B
10-03-01: Select T-Point
11-01: Adjust numbering plan (3XX, 4XX type Extension Access, 1XX, 2XX type F-route Access)
11-02: Extension Number
14-05: Adjust Trunk group for PRI card (Ex TrG 7)
21-13: ISDN Calling Party Number Setup for Extension
22-02: Set PRI trunk type to TIE line
22-09-01: Dial-In Receive Digit set 3 (for TrG 7)
22-11-01 and 22-11-02: Ex Receive number 300 then Target 300
44-02: F-route Dial Analysis table, Table Entry = 1,2, when dial 1,2 then service type is F-route table, additonal data set 1
44-05-01: F-route table 1, 2. Trunk Group priority Number 1 set 7

----------------------------------------------------------------
Something was wrong with that programming, please show me know. Thanks

 

[CoralTech]

You don't need DID stuff using tie.

44-02 X@@ x being lead digit. Point to F-route table.

44-05 You need 01,09

You also will need a T-1 crossover cable.

 

[Sinjisn]

Site A is T-Point and Site B is T-Point, no call can making.
Site A is T-Point and Site B is S-Point, I can make a call from A to B, but can't make a call from B to A.

 

[CoralTech]

Clock sources must be master and slave.

 

[Sinjisn]

Nothing changes in case
Programing Manual: If set to Slave System, system is synchronized to network clock. If set to Master System, system is not synchronized to the network clock.

 

[CoralTech]

Ok, so you have no knowledge to what you are doing. Free lesson, every T1 (PRI) must have a master to a slave for clocking. Now for a stupid question, are these system next to each other on a bench or do you have a point to point T1 over the public network?

 

[Sinjisn]

Answer for a stupid question, these system connect directly point to point via T1 crossover cable.
Please giving clear instructions if you can. Thanks a lot for your help!