how to change all analogue ext numbers 2

[MahbubR]

Hi,
we have ext like 60101, 60102, 60103 .. 60901, 60902 ext
i want to change all ext to be like 70101, 70102, 70103 .. 70901, 70902
basically change the 6 to 7 with all existing settings as it is.

which command does the job if someone can let me know?

 

[inlsp05]

which type of sw or hw? tsw-tse ? which type of extention ats-dts-generic?

PG4E

 

[MahbubR]

Below information about our ext


MDSH> sudip:dir=60101;
DIRECTORY INFORMATION AT 12:38 08APR19
DIRECTORY NUMBER : 60101
TYPE OF DIRECTORY NUMBER : ATS
NAME :
ADDITIONAL NUMBER :

EXTENSION TERMINAL DATA
EQU TERMD ADN
0020000

EXTENSION DIRECTORY CATEGORIES
CAT TRAF SERV CDIV ROC TRM
1 00010115 0200020700000 01115111131 000001 1

ADC CUST LANG BSEC MCOST OFTIME FDTIME
000000001 - - 0 - 0 0

 

[inlsp05]

ats
exdnc:dirold=60101,dir=70101;
check 7xxxx is in ex series with nadap

PG4E

 

[MahbubR]

I have more than 1000 ext
Please advise what can be the easy way to do it.

 

[inlsp05]

consult the parameter description for analogue extension.
& is permitted for this parameter.

PG4E

 

[parnum]

Create a script file in excel and save as .txt

Run in the changes

EXDNCIROLD=60101,DIR=70101:
EXDNCIROLD=60102,DIR=70102;

Etc

This is how PCREGEN works...

Best parnum

 

[ceejay55]

how much data corruption do you think will happen ?

if it was me i would make up regen script files

EXTEE ,then EXTEI

might save a lot of grief

Or if V5 or V6 i would rebuild it off siteat V7 with new SSD

 

[MahbubR]

hi
i know that its a bit late but i tried the command and its not recognized:
MDSH> Exdnc:dirold=61590,dir=71590;
Unconfigured command (Exdnc:dirold=61590,dir=71590) -- cannot execute

 

[inlsp05]

hi
first off all run this:
ts_about


PG4E

 

[ceejay55]

exdnc ,exeqc ksdnc ksexc etc commands were all removed for good reason -they caused corruption !
extee ,then extei
make up a file using regen or rebuild it from scratch

 

[MahbubR]

MDSH> ts_about
====== MX-ONE Telephony System ======
Version: 5.0 SP5 Hotfix2 build10

RPM Packages
============
Telephony Server 14.170.16 :
eri_sn-14.170.16-MR

Media Gateway File system 2.0 :
egx_rfs-2.0-1

Media Gateway 10.21 :
egx_sw-10.21-1

Media Gateway Classic 1.5.4 :
lsue_sw-1.5.4-1

Manager 9.316.7 :
eri_om-9.316.7-201411281529

 

[inlsp05]

4. Enter the command EXEQC to move extension A to a free position.(tse v5.1)
do you set 70101 &x... to ext series?
number_initiate -numbertype EX -number 70101


PG4E

 

[MahbubR]

thanks for your reply

my issue is :
we have ext like 60101, 60102, 60103 .. 60901, 60902 ext
i want to change all ext to be like 70101, 70102, 70103 .. 70901, 70902

and i have over 1000 ext to change.
is there no way to do it like old ext =x, new ext=y then i can make a excel script for all numbers and just run it.

 

[doktor]

I agrre with ceejay55

Swapping numbers and EQU positions should be avoided.

"how much data corruption do you think will happen ?"

Print all (EXDDP/EXCAP) --> change transmit file with regards to the new numbers --> make a test (delete/change/initiate).
--> Use TextPad or Excel to buold the "delete/EXTEE" file and the EXTEI/initiate file. --> Run the delete file (remember Y; to accept deletion of EXTEE) ->
Check for busy extensions - they cannot be deleted. ( run a logfile, while transmitting the "delete file") --> run the initiate file (EXTEI) and make a backup afterwards.

1000 numbers will be done in 2 hours.





///doktor
____________________________________

http://www.kandu.dk/spg153996.aspx

 

[MahbubR]

thank you inlsp05, parnum, ceejay55, doktor for your suggestions and time.